Beta 1760 PA/AC Manuale utente

ENFRAIT

AMPEROMETRIC CLAMP

MOD. 1760 PA/AC

PINZAAMPEROMETRICA

MOD. 1760 PA/AC

PINCE AMPEREMETRIQUE

MOD. 1760 PA/AC

ZANGENSTROMMESSER

MOD. 1760 PA/AC

PINZAAMPERIMÉTRICA

MOD. 1760 PA/AC

ESDE

AMPEROMETRIC CLAMP

MOD. 1760 PA/AC

SAFETY NOTES

Do not exceed the maximum allowable input range of any function

Do not apply voltage to meter when resistance function is selected.

Set the function switch OFF when the meter is not in use.

WARNINGS

Set function switch to the appropriate position before measuring.

When measuring volts do not switch to current/resistance modes.

Do not measure current on a circuit whose voltage exceeds 240V.

•

This symbol, adjacent to another symbol or terminal, indicates the user must refer to this

manual for further information.

This symbol, adjacent to a terminal indicates that under normal use hazardous voltages

may be present

Double insulation

CAUTIONS

Improper use of this meter can cause damage, shock, injury or death. Read and understand this

user manual before operating the meter.

Always remove the test leads before replacing the battery.

Inspect the condition of the test leads and the meter itself for any damage before operating

the meter. Repair or replace any damage before use.

Use great care when making measurements if the voltages are greater than 25 V AC rms or

35 V DC. These voltages are considered a shock hazard.

Remove the battery if the meter is to be stored for long periods.

Always discharge capacitors and remove power from the device under test before

performing Diode, Resistance or Continuity tests.

Voltage checks on electrical outlets can be difcult and misleading because of the uncertainty

of connection to the recessed electrical contacts. Other means should be used to ensure that the

terminals are not “live”.

If the equipment is used in a manner not specied by the manufacturer, the protection provided

by the equipment may be impaired.

•

When changing ranges using the selector switch always disconnect the test leads from the circuit

under test.

Do not exceed the maximum rated input limits.

•

Inputs limits

Function Maximum input

A AC 1000 A

V DC, V AC 600 V DC/AC

Resistance, diode, continuity, Capacitance,

Frequency, Duty cycle, test 250 V DC/AC

Temperature 60 V DC/24 V AC

1. Current clamp

2. Clamp trigger

3. Data hold and backlight

button

4. Mode select button

5. LCD display

6. COM input jack

7. Rotary function switch

8. Range select button

9. Hz/% duty button

10. V- - °C/F jack

11. Battery cover

AC (alternating current) and DC (direct currrent)

Minus sign

4 digits (0 to 3999) measurement reading

Auto Range mode

Diode test mode

Audible Continuity

Data Hold mode

°C, °F, µm,V, A,K, M, - units of measure list

1

2

3

4

5

6

7

8

METER DESCRIPTION

4 5 6 7 8

Functions Range and resolution Accuracy (% of reading)

40.00 AAC ± (2,5% +10 digits)

AC Current 400.0 AAC ± (2,5% +5 digits)

1000 AAC ± (3.0% +4 digits)

400.0 mV DC ± (0.8% +3 digits)

4.000 V DC

DC Voltage 40.00 V DC ± (1.5% +3 digits)

400.0 V DC

600 V DC ± (2.0% +3 digits)

400.0 mV AC ± (0.8% +20 digits)

4.000 V AC

AC Voltage 40.00 V AC ± (1.8% +5 digits)

400.0 V AC

600.0 V AC ± (2.5% +5 digits)

400.0 ± (1.0% +4 digits)

4.000 K

Resistence 40.00 K ± (1.5% +2 digits)

400.0 K

4.000 M ± (2,5% +3 digits)

40.00 M ± (3,5% +5 digits)

SPECIFICATIONS

40.00 nF ± (5.0% reading +100 digits)

400.0 nF ± (3.0% reading +5 digits)

Capacitance 4.000 µF ± (3.5% reading +5 digits)

40.00 µF

100.0 µF ± (5.0% +5 digits)

5.000 Hz ± (1,5% +5 digits)

50.00 Hz

500.0 Hz ± (1,2% +2 digits)

Frequency 5.000 KHz Sensivity: 10mV rms min

50.00 KHz

500.0 KHz

5 MHz ± (1.5% reading +10 digits)

10.00 MHz

Duty Cycle 0.5 a 99.0% ± (1.2% reading + 2 digits)

Pulse width: 100us – 100ms

Temperature -50.0 to 400.0°C ± (3.0% reading +5°C)

(Type K probe) 400 to 1000°C

(probe accuracy -58.0 a 400.0°F ± (3.0% reading +7°F)

not included) 400 to 1832 °F

Note: no autoranging and 400mV AC Voltage range

Clamp size Opening 1.2” (30mm) approx

Diode Test Test current of 0.3 mA typical - Open circuit voltage 1.5V DC typical

Continuity Check Threshold <1000; Test current < 1mA

Low Battery Indication “ “ is displayed

Overrange Indication “OL” is displayed

Measurements Rate 2 per second, nominal

Input Impedance 7.8 Mohm (VDC and VAC)

Display LCD 4 digits backlighted

AC Current 50/60Hz (AAC)

AC Voltage bandwidth 50/60HZ (VAC)

Operating Temperature 14 to 122°F (-10 to 50°C))

Storage Temperature -14 to 140°F (-30 to 60°C))

Relative Humidity 90% (0°C to 30°C); 75% (30°C to 40°C); 45% (40°C to 50°C)

Altitude Operating: 3000 m; Storage 10.000 m

Over voltage Category III 600 V

Battery One “9V” battery

Auto OFF Approx. 30 minutes

Dimensions/Weight 229 x 80 x 49 mm / 303 g

Safety For indoor use and in accordance with Overvoltage Category II,

Pollution Degree 2 - Category II includes local level, appliance,

portable equipment, etc., with transient overvoltages less than

Overvoltage Cat. Ill

OPERATION

Notices: Read and understand all warning and precaution statements listed in the safety

section of this operation manual prior to using this meter. Set the function select switch to

the OFF position when the meter is not in use.

AC Current Measurements

Warning: Ensure that the test leads are disconnected from the meter before making current

clamp measurements.

Set the Function switch to the 1000A or 400A ‘or 40A range. If the range of the measured is

not known, select the higher range rst then move to the lower range if necessary.

Press the trigger to open jaw. Fully enclose one conductor to be measured

The clamp meter LCD will display the reading

DC/AC Voltage Measurements

Insert the black test lead into the negative COM terminal

and the red test lead into the positive V terminal.

Set the function switch to the V position.

Select AC or DC with the MODE button

Connect the test leads in parallel to the circuit under test.

Read the voltage measurement on the LCD display.

1

2

3

1

2

3

4

5

NO YES

Resistance and Continuity Measurements

Insert the black test lead into the negative COM terminal and the red test lead into the

positive terminal.

Set the function switch to the position.

Use the multifunction MODE button to select resistance.

Touch the test probe tips across the circuit or component under test. It is best to disconnect

one side of the device under test so the rest of the circuit will not interferewith the resistance

reading.

For Resistance tests, read the resistance on the LCD display.

For Continuity tests, if the resistance is < 100 , a tone will sound.

Diode Measurements

Insert the black test lead banana plug into the negative COM jack and the red test lead banana

plug into the positive diode jack.

Turn the rotary switch to the position.

Press the MODE button until appears in the display.

Touch the test probes to the diode under test. Forward voltage will indicate 0.4V to 0.7V.

Reverse voltage will indicate “OL”. Shorted devices will indicate near OmV and an open

device will indicate “OL” in both polarities.

1

2

3

4

5

6

1

2

3

4

Red probe Red probe

Black

probe

Black

probe

Indice

Lingue:

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente