Billion BiPAC 7300M Manuale utente
BiPAC 7300M
802.11g MIMO ADSL2+ Router
Quick Start Guide
Billion BiPAC 7300M 802.11g MIMO ADSL2+ Router
For more detailed instructions on configuring and using
the 802.11g MIMO ADSL2+ Router, please refer to the
on-line manual.
Package Contents
BiPAC 7300M 802.11g MIMO ADSL2+ Router
CD-ROM containing the on-line manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Warning
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as othe
r
equipment.
Do not open or repair the case yourself. If the router are too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this product and all accessories outdoors.
A
ttention
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
1
Quick Start Guide
The Front LEDs
BiPAC 7300M
LED Meaning
1 PPP : Lit steady when there is a PPPoA / PPPoE connection.
2 ADSL: Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port: Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4 WLAN : Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS : Lit when the system is ready.
6 PWR : Lit when power is ON.
2
Billion BiPAC 7300M 802.11g MIMO ADSL2+ Router
The Rear Ports
BiPAC 7300M
3
4 31
2
Port Meaning
1 DC 12V/1A Connect the supplied power adapter to this jack.
2 RESET
(Emergency/Fai
lure Recovery)
1.After the device is powered on, press it to perform Failure
recover for a dead routers:
Simply hold the Emergency/Failure Recovery Button” when power
on the routers and download the Application if necessary.
2.Perform the Emergency Recover for the missing Password
case:(Using LEDs indications)
Simply hold the Emergency/Failure Recovery Button, when router
can be accessed from GUI, until the LEDs all turn Off, turn On and
then Turn Off. Then, router will perform configuration factory reset
and router reboot.
3 LAN
(RJ-45
connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
4 ADSL Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
Quick Start Guide
Connecting BiPAC 7300M
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, and WLAN LEDs are lit steadily and that the relevant LAN LED is
lit.
4
Billion BiPAC 7300M 802.11g MIMO ADSL2+ Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
5
Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6
Billion BiPAC 7300M 802.11g MIMO ADSL2+ Router
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
7
Quick Start Guide
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Protocols tab.
2. Select TCP/IP Protocol and click
Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
8
Altri manuali per BiPAC 7300M
2
Indice
Altri manuali Billion Router di rete
Billion
Billion BiPAC 8900AX-1600 R2 Manuale utente
Billion
Billion BiPAC 711C2 Manuale utente
Billion
Billion Bipac 74 Series Manuale utente
Billion
Billion BiPAC VGL Manuale utente
Billion
Billion BiPAC 7300N Manuale utente
Billion
Billion BIPAC-7402 Manuale utente
Billion
Billion myGuard 7202 Manuale utente
Billion
Billion BiPAC 7402VGO Manuale utente
Billion
Billion 800VGT Manuale utente
Billion
Billion BiPAC 5100 Manuale utente
Billion
Billion BiPAC 8500 Manuale utente
Billion
Billion BiPAC 7402(G)(L) R3 Series Manuale utente
Billion
Billion BiPAC 7800(N) Manuale utente
Billion
Billion BiPAC 7800GZ Manuale utente
Billion
Billion BIPAC-645 Manuale utente
Billion
Billion BiPAC 7402NX Manuale utente
Billion
Billion BiPAC 8501 Manuale utente
Billion
Billion myGuard 7500GL Manuale utente
Billion
Billion BiPAC 6404VGP R3 Manuale utente
Billion
Billion myguard 6700G Manuale utente
