Billion myGuard 7202 Manuale utente
myGuard 7202 / 7202G
(802.11g) Security ADSL2+ Router
Quick Start Guide
myGuard 7202(G) ADSL2+ Modem/ Router
1
Package Contents
myGuard 7202(G) ADSL2+ Modem/Router
CD-ROM containing the on-line manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Do not use the myGuard 7202(G) in high humidity or high
temperatures.
Do not use the same power source for the myGuard 7202(G) as
other equipment.
Do not open or repair the case yourself. If the myGuard
7202(G) is too hot, turn off the power immediately and have it
repaired at a qualified service center.
Avoid using this product and all accessories outdoors.
Warning
Place the myGuard 7202(G) on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
A
ttention
For more detailed instructions on configuring and using
the (802.11g) ADSL Router, please refer to the on-line
manual.
Quick Start Guide
2
The Front LEDs
myGuard 7202
myGuard 7202G
LED Meaning
1 PPP : Lit steady when there is a PPPoA / PPPoE connection.
2 ADSL: Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port:
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4
WLAN :
(7202G
only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS : Lit when the system is ready.
6 PWR : Lit when power is ON.
myGuard 7202(G) ADSL2+ Modem/ Router
3
The Rear Ports
myGuard 7202
myGuard 7202G
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3
RESET
(Emergency/Fail
ure Recovery)
1. After the device is powered on, press it to perform Failure
recover for a dead routers:
Simply hold the Emergency/Failure Recovery Button” when power
on the routers and download the Application if necessary.
2. perform the Emergency Recover for the missing Password
case:(Using LEDs indications)
Simply hold the Emergency/Failure Recovery Button, when router
can be accessed from GUI, until the LEDs all turn Off, turn On and
then Turn Off. Then, router will perform configuration factory
reset and router reboot
4
LAN
(RJ-45
connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
5 LINE Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
2 5
4
2
3
45
1
3
Quick Start Guide
4
Connecting myGuard 7202
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
myGuard 7202(G) ADSL2+ Modem/ Router
5
Connecting myGuard 7202G
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, and WLAN LEDs are lit steadily and that the relevant LAN LED is
lit.
Quick Start Guide
6
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
myGuard 7202(G) ADSL2+ Modem/ Router
7
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
Quick Start Guide
8
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
Altri manuali per myGuard 7202
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Billion Router di rete
Billion
Billion BiPAC 5200G Series Manuale utente
Billion
Billion BiPAC 5200G Series Manuale utente
Billion
Billion BiPAC 5210S Manuale utente
Billion
Billion BiPAC 5200 Manuale utente
Billion
Billion myGuard 7500GL Manuale utente
Billion
Billion BIPAC-741 GE V2.0 Manuale utente
Billion
Billion BiPAC 7800GZ(L) Manuale utente
Billion
Billion BIPAC-7402 Manuale utente
Billion
Billion BiPAC 8900AX-1600 R2 Manuale utente
Billion
Billion BIPAC 7402W Manuale utente
Billion
Billion BiPAC 6300VNOZ Manuale utente
Billion
Billion BiPAC 7402R2 Manuale utente
Billion
Billion BiPAC 8501 R3 Manuale utente
Billion
Billion (802.11g) ADSL2+ Modem/Router BIPAC 5102G Manuale utente
Billion
Billion BiPAC 5100 Manuale utente
Billion
Billion BiPAC 2072 Manuale utente
Billion
Billion BiPAC 5100S Manuale utente
Billion
Billion BiPAC 5100S Manuale utente
Billion
Billion BiPAC 4700ZU Manuale utente
Billion
Billion BiPAC 7300 Manuale utente
