Blizzard Lighting ICE 30 Manuale utente

Blizzard Lighting, LLC

www.blizzardlighting.com

Wisconsin, USA

Page 2

TABLE OF CONTENTS

ICE 30™ 30W LED Moving Head Spot 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The ICE 30™ Spot 5

Features 5

DMX Quick Reference 5

The ICE 30 Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of ICE 30’s™ 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Fixture Linking (Master/Slave Mode) 9

Mounting/Rigging 9

 UsingthisxturewiththewiCICLE®WirelessDMXSystem 10

4. Operating Adjustments 12

The Control Panel 12

Control Panel Menu Structure & Adjustments 12

Setting the pan/tilt/Menu to inverting or non-inverting 12

 SettingtheDMXchannelconguration   12

Setting the maximum pan angle 12

Setting the maximum tilt angle 12

Additional User Adjustments 12

Service Functions 13

 Resettingthexture     13

Restoring Factory Defaults 13

Stand-Alone (“Auto”) Mode 13

Master/Slave (“Auto” or “Sound Active”) 13

DMX Mode 13

Gobo Replacement 13

DMX Channel Values In-Depth 14

Troubleshooting 16

5. Appendix 17

A Quick DMX Lesson 17

Keeping Your ICE 30 Spot As Good As New 18

Returns (Gasp!) 18

Shipping Issues 18

Tech Specs 19

Page 3

1. GETTING STARTED

What’s In The Box?

 •1xICE30™Spot

 •AnEver-So-HandyPowerCord

 •ASweetSafetyCable&setofMountingBrackets

 •ThisLovelyUserManual

Getting It Out Of The Box

You’reascooollldasice...butnotwillingtosacriceyourlove...fora

greatLEDmovingheadxture!Nowthatyou’vegotyourICE30,you

should carefully unpack the box and check the contents to ensure that

all parts are present and in good condition. If anything looks as if it

has been damaged in transit, notify the shipper immediately and keep

the packing material for inspection. Again, please save the carton and

allpackingmaterials.Ifaxturemustbereturnedtothefactory,itis

importantthatthexturebereturnedintheoriginalfactoryboxand

packing.

Powering Up!

Allxturesmustbepowereddirectlyoffaswitchedcircuitandcannot

be run off a rheostat (variable resistor) or dimmer circuit, even

if the rheostat or dimmer channel is used solely for a 0% to

100% switch.

AC Voltage Switch -Notallxtureshaveavoltageselectswitch,so

pleaseverifythatthextureyoureceiveissuitableforyourlocalpow-

ersupply.Seethelabelonthextureorrefertothexture’sspeci-

cationschartformoreinformation.Axture’slistedcurrentratingis

itsaveragecurrentdrawundernormalconditions.Checkthextureor

device carefully to make sure that if a voltage selection switch exists

that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit

matches the line voltage applied. Damage to your xture may

result if the line voltage applied does not match the voltage

indicated on the voltage selector switch. All xtures must be

connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email.

We’ll be happy to help, honest.

Blizzard Lighting

W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA

[email protected] | Phone: 866-493-6025

www.blizzardlighting.com

Page 4

SAFETY INSTRUCTIONS

•PleasekeepthisUserGuideforfutureuse.Ifyouselltheunittosomeone

else, be sure that they also receive this User Guide.

•ALWAYSmakesurethatyouareconnectingtothepropervoltage,andthat

the line voltage you are connecting to is not higher than that stated on the de-

calorrearpanelofthexture.

•Thisproductisintendedforindooruseonly.

•Topreventriskofreorshock,donotexposexturetorainormoisture.

•Makesuretherearenoammablematerialsclosetotheunitwhileoperating.

•Theunitmustbeinstalledinalocationwithadequateventilation,atleast

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

•ALWAYSdisconnectfromthepowersourcebeforeservicingorreplacingfuse

and be sure to replace with same fuse size and type.

•ALWAYSsecurextureusingasafetychain.NEVERcarrythexturebyits

head. Use its carrying handles.

•DONOToperateatambienttemperatureshigherthan104°F(40°C).

•Intheeventofaseriousoperatingproblem,stopusingtheunitimmediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

•NEVERconnectthedevicetoadimmerpack.

•Makesurethepowercordisnevercrimpedordamaged.

•Neverdisconnectthepowercordbypullingortuggingonthecord.

•Avoiddirecteyeexposuretothelightsourcewhileitison.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

yourunitmayrequireservice,pleasecontactBlizzardLightingatsup-

[email protected].

Page 5

2. MEET THE ICE 30™SPOT

CONTROL FEATURES

• 10 or 15-channel DMX LED moving yoke

• Pan: 540º/360º/180º Tilt: 270º/180º/90º

• Color wheel: 7 colors + white

• Rainbow color spin at variable speeds

• Rotating gobo wheel with gobo shake

• 6 interchangeable, rotating slot-n-lock gobos + open (1 glass installed)

• 8xedgobos

• Gobo wheel spin at variable speeds

• 3-facet rotating prism

• Variable electronic strobe

• Variable electronic dimmer (0 – 100%)

• RemotefocusviaDMX(2m~innity)

• Remotexturereset

• Multiple built-in automated & sound activated programs

ADDITIONAL FEATURES

• Lux: 5,300 @ 1m

• Gobo size: 27.9mm outside, 23mm image, 1.2mm max thickness

• Beam Angle: 14º

• Light source: 30W White LED, 50,000 hrs

DMX Quick Reference

Channel What It Does... (15 Chan-

nel)

(10 Channel Mode)

1Pan Pan

2 Tilt Tilt

3 Pan Fine (16-Bit) Color

4 Tilt Fine (16-Bit) Fixed Gobos

5 Motor Speed Rotating Gobos

6 Color Gobo Rotation

7 Fixed Gobos Strobe

8 Rotating Gobos Dimmer

9 Gobo Rotation Prism

10 Shutter/Strobe Focus

11 Dimmer

12 Functions

13 Movement Macros

14 Prism

15 Focus

Page 6

Figure 1: The ICE 30 Pin-Up Picture

Lens

Control Panel

LCD

Readout

Head

Figure 2: The Rear Connections

AC Power

Fuse Cover

DMX In DMX Out

Microphone

DMX Indicator

Fan Guard

Page 7

3. SETUP

Fuse Replacement

Withaatheadscrewdriver,wedgethe

fuse holder out of its housing. Remove the

damaged fuse from its holder and replace

with exact same type fuse. Insert the fuse

holder back in its place and reconnect

power.

Connecting A Bunch of ICE 30™eseses

You will need a serial data link to run light shows using a DMX-512

controllerortorunshowsontwoormorexturessettosyncinmas-

ter/slaveoperatingmode.Thecombinednumberofchannelsrequired

byallthexturesonaserialdatalinkdeterminesthenumberofx-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also,connectingmorethan32xturesononeserialdatalinkwithout

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal.

The maximum recommended cable-run distance is 500 meters (1640

ft).Themaximumrecommendednumberofxturesonaserialdata

linkis32xtures.

Data/DMX Cabling

Tolinkxturestogetheryou’llneeddatacables.Youshouldusedata-

gradecablesthatcancarryahighqualitysignalandarelessproneto

electromagnetic interference.

Forinstance,Belden©9841meetsthespecicationsforEIARS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR

connector on the other end. (Duh!)

CAUTION:Donotallowcontactbetweenthecommonandthex-

ture’s chassis ground. Grounding the common can cause a ground

loop,andyourxturemayperformerratically.Testcableswithan

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.

They are widely available over the internet and from specialty retailers If you’d like to build your own, the

chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male

(Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)

on the controller.

Step 2: Connect the female connector of the

DMXcabletotherstxture’smaleconnec-

tor (input). Note: It doesn’t matter which

xtureaddressistherstoneconnected.

Werecommendconnectingthexturesin

terms of their proximity to the controller,

ratherthanconnectingthelowestxture

numberrst,andsoon.

Step 3:Connectotherxturesinthechain

from output to input as above. Place a DMX

terminatorontheoutputofthenalxture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the

DMX cable to the output (female) 3 pin connector of

therstxture.

2. Connect the end of the cable coming from the

rstxturewhichwillhavea(female)3pinconnec-

tortotheinputconnectorofthenextxturecon-

sisting of a (male) 3 pin connector. Then, proceed

to connect from the output as stated above to the

inputofthefollowingxtureandsoon.

A quick note: Often,

the setup for Master-

Slave and Standalone

operationrequiresthat

therstxtureinthe

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.

Secondarily,thextures

that follow may also re-

quireaslavesetting.

Check the “Operating Adjustments” section in this manual for com-

pleteinstructionsforthistypeofsetupandconguration.

Mounting & Rigging

ThisxturemaybemountedinanySAFEpositionprovidedthereis

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

xtureusingasuitable“C”or“O”typeclamp.Theclampshouldbe

ratedtoholdatleast10xthexture’sweighttoensurestructuralsta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly“rated”riggingisusedwhenmountingxutresoverhead.

Adjusttheangleofthexturebylooseningbothknobsandtiltingthe

xture.Afterndingthedesiredposition,retightenbothknobs.

•Whenselectinginstallationlocation,takeintoconsiderationlamp

replacement access (if applicable) and routine maintenance.

•SafetycablesMUSTALWAYSbeused.

•Nevermountinplaceswherethexturewillbeexposedtorain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

USING THIS FIXTURE WITH THE wiCICLE® WIRELESS

DMX SYSTEM

In addition to the unbridled thrill you al-

readyreceivedthersttimeyouplugged

inyourxture,you’llbedelightedtoknow

thatThisxturealsoworksseamlesslywith

our wiCICLE®Wireless DMX system, without additional power.

•ONLYxturesbearingthislogoarecertiedforusewiththewiCI-

CLE®without external power.

• Unauthorized modication and/or using the wiCICLE®with

unapproved xtures may cause damage to the wiCICLE®or

xture. UNDER NO CIRCUMSTANCES IS BLIZZARD LIGHTING

RESPONSIBLE FOR ANY DAMAGE FROM SUCH OPERATION.

•FixturesbearingtheabovelogoMUST only use cable and connec-

tors which separate chassis/case ground from cable shielding. Cabling

with the shield connected to the connector’s case/chassis may cause

malfunction and damage to the wiCICLE®orxture.

•wiCICLE®transmittershaveadditionalpowerrequirements

andthereforecannotbepowereddirectlyfromthexture.You

will need to utilize the supplied AC/DC adaptor to drive wiCI-

CLE®transmitters in your system.

WE HAD THIS SPACE, SO WE FIGURED WE’D DRAW

YOU A PICTURE:

Antenna Housing & 1/2-wave

Antenna

Antenna ferrule & articulation

joint

Stainless Steel Housing

Recessed Selector Button

Status LED

3-Pin XLR Connector

(Male on transmitter, Female

on receiver model)

Indice

Altri manuali Blizzard Lighting Attrezzatura di illuminazione

Blizzard Lighting

Blizzard Lighting Flurry Spot Manuale utente

Blizzard Lighting

Blizzard Lighting Lo-Pro Flux Manuale utente

Blizzard Lighting

Blizzard Lighting HUSH PAR Theatrik Manuale utente

Blizzard Lighting

Blizzard Lighting HotStik 5 COB Mini Manuale utente

Blizzard Lighting

Blizzard Lighting RokBox Manuale utente

Blizzard Lighting

Blizzard Lighting ToughPar V12 Manuale utente

Blizzard Lighting

Blizzard Lighting G70 Manuale utente

Blizzard Lighting

Blizzard Lighting Tour QT Skywire Manuale utente

Blizzard Lighting

Blizzard Lighting SNAKE EYES Manuale utente

Blizzard Lighting

Blizzard Lighting Flurry EXA Manuale utente

Blizzard Lighting

Blizzard Lighting Pocket Rocket Manuale utente

Blizzard Lighting

Blizzard Lighting G-Max 150 Manuale utente

Blizzard Lighting

Blizzard Lighting Colorise Quadra Manuale utente

Blizzard Lighting

Blizzard Lighting Puck Pro Zoom EXA Manuale utente

Blizzard Lighting

Blizzard Lighting Stiletto Z7 Manuale utente

Blizzard Lighting

Blizzard Lighting mikrokassette Manuale utente

Blizzard Lighting

Blizzard Lighting KAYO.MORPH Manuale utente

Blizzard Lighting

Blizzard Lighting Flurry TRI Manuale utente

Blizzard Lighting

Blizzard Lighting Kontrol 5 Manuale utente

Blizzard Lighting

Blizzard Lighting The Puck RGB Unplugged Manuale utente

Blizzard Lighting

Blizzard Lighting Pocket Nebula Manuale utente

Blizzard Lighting

Blizzard Lighting Puck CSI Xtreme Manuale utente

Blizzard Lighting

Blizzard Lighting Switch Blade X3 Manuale utente

Blizzard Lighting

Blizzard Lighting ToughPar V12 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente