BOS BS-DET2000BT Manuale utente

BS-DET2000BT /RF MANUAL

VERSION 1.4

FACE RECOGNITION AND TEMPERATURE DETECTION DEVICE BS-DET2000BT

CAUTIONS

•To ensure temperature measurement, it is recommended to have a visible forehead

•Once the device is turned on, let it calculate the ambient temperature, about 15-20

minutes

•Once the device has been positioned, do not change its position, otherwise it will be

necessary to restart it and have it perform a re-setting

•For a more accurate measurement, it is recommended to install the device in a working

environment ranging from 15 to 30 ° C. The device has a detection range ranging from 34

to 42 ° C. MEASUREMENT IS A CUTANEOUS MEASUREMENT! SOME ABNORMAL

MEASUREMENTS MAY BE AFFECTED BY THE ENVIRONMENTAL CONDITIONS!

•This operation manual is for reference only. All aspects and functions of the product are

subject to the actual product and may be subject to change

•Do not expose the lens and sensor to strong light sources, doing so will affect the

acquisition or could damage the lens

•Configure all passwords and other product security settings and remember your

credentials

•Biometric products may not be 100% suitable for any security environment or high

security use, please use combined forms of authentication

•The firmware of the device will be updated from time to time. For a better experience,

please update whenever a new update is available

•The BS-DET2000BT device is NOT a diagnostic device nor a medical device, any abnormal

temperature detection must then be verified using a suitable thermometer

•During detection please do not speak to avoid heat escaping and consequently altering

the temperature measurement

IMPORTANT NOTES REGARDING THE

READING OF TEMPERATURE

It should be borne in mind that the DET2000 thermoscanner is a skin temperature measurement

device that can be influenced by various factors:

•Exposure to sources of heat / cold

•Physical movement

•Stress

•Embarrassment

And how much else can cause an increase / decrease in skin temperature

Furthermore, the measurement is influenced by the temperature of the environment in which the

DET2000 is installed and it is recommended to be between 15 and 30 ° C.

The temperature measurement range is 35-42 ° C.

The measurement of the person's temperature starts from 35 ° C body temperature which is

rounded to a minimum of 35.8 ° C by the DET2000 device; skin temperatures below 35 ° C (due to

external temperature) will not be detected and therefore an acclimatization time will be required

before taking the measurement; the same principle applies to excessively high skin temperatures

(due to various external factors such as heat, sun, etc.) which will require an acclimatization time.

Readings with skin temperature altered by external factors would not be reliable.

For correct operation, the coverage field of the thermal module must not reflect sources of heat

or cold (doors, windows, lamps) and how much it can influence correct measurement.

It should also be noted that:

The normal temperature value, and therefore the point where the fever 'starts', is as follows:

•rectally - measured with a traditional mercury thermometer: from 36.6 ° C to 38.0 ° C (this

measurement is the most reliable as it is internal)

•axillary - measured with a traditional thermometer: from 34.7 ° C to 37.3 ° C (may deviate

even 1.9 ° C from the rectal measurement)

•on the forehead - measured with an infrared forehead thermometer: from 35.4 ° C to 37.4 ° C

(can deviate even 0.7 ° C from the axillary measurement and 1.2 ° C from the rectal

measurement; external factors such as exposure to cold or hot ambient temperatures)

The 0.3 ° C margin of error of the DET2000BT device is confirmed and tested by various series of

measurements performed on different days, on different subjects, with the device installed in an

environment with a temperature of around 20 ° C, respecting the acclimatization time and performing

cycles and 100 measurements on acclimatized subjects; the average margin of difference between one

measurement and another is less than 0.2 ° C.

INDEX 
PRODUCT OVERVIEW ................................................................................................................................ 7 
1 INTRODUCTION TO THE PRODUCT .................................................................................................. 7 
2 PRODUCT CHARACTERISTICS ............................................................................................................ 7 
3 FIELDS OF APPLICATION..................................................................................................................... 8 
PRODUCT INSTALLATION ........................................................................................................................ 8 
1 INSTALLATION...................................................................................................................................... 9 
2 INSTALLATION ON DETPAV110 PEDESTAL ..................................................................................... 9 
3 INSTALLATION ON DETBASE TABLE BASE.................................................................................... 10 
4 WALL INSTALLATION........................................................................................................................ 11 
WIRING INSTRUCTIONS ......................................................................................................................... 11 
CLIENT SOFTWARE .................................................................................................................................. 12 
1 IPC DEMO INSTALLATION................................................................................................................ 12 
2 LOGIN INTERFACE ............................................................................................................................. 13 
3 INTERFACE PREVIEW......................................................................................................................... 14 
4 CREATION AND MANAGEMENT OF LISTS.................................................................................... 15 
4.1 IMAGE REQUIREMENTS OF FACES........................................................................................... 15 
4.2 IMPORTING A SINGLE FACE IMAGE........................................................................................ 16 
4.3 MULTIPLE FACES IMPORT......................................................................................................... 17 
4.4 REAL-TIME FACES IMPORT....................................................................................................... 18 
4.5 IMPORTING THE FACE LIBRARY IN BINARY FORMAT......................................................... 19 
4.6 EXPORT FACE LIBRARY.............................................................................................................. 19 
5 PERIPHERAL CONTROL..................................................................................................................... 20 
5.1 BASIC SETTINGS .......................................................................................................................... 20 
5.2 CONTROL OF ALARM OUTPUTS (DOOR AND TURN CONTROL) ...................................... 20 
5.3 INPUT / OUTPUT CONFIGURATION........................................................................................ 21 
5.4 WIEGAND SETTINGS.................................................................................................................. 22 
5.5 DISPLAY SETTINGS..................................................................................................................... 22 
5.6 LED LIGHT .................................................................................................................................... 23 
5.7 SERIAL PORTS.............................................................................................................................. 23 
6 SYSTEM CONFIGURATION............................................................................................................... 24 
6.1 DATE AND TIME SETTINGS ....................................................................................................... 24 

6.2 DST SETTINGS ............................................................................................................................. 24 
6.3 NETWORK SETTINGS ................................................................................................................. 25 
6.4 PORT ............................................................................................................................................. 25 
6.5 P2P ................................................................................................................................................ 26 
6.6 TF CARD ....................................................................................................................................... 28 
6.7 USER MANAGEMENT................................................................................................................. 29 
6.8 EMAIL............................................................................................................................................ 30 
6.9 STORAGE MANAGE.................................................................................................................... 30 
7 PARAMETER SETTINGS..................................................................................................................... 31 
7.1 FACIAL RECOGNITION ............................................................................................................... 31 
7.2 TEMPERATURE CONFIGURATION ........................................................................................... 32 
7.3 MINIMUM DIMENSION DETECTION....................................................................................... 32 
7.4 SCHEDULING MANAGEMENT.................................................................................................. 33 
7.5 AUDIO........................................................................................................................................... 33 
7.6 OSD SETTINGS ............................................................................................................................ 34 
7.7 VIDEO PARAMETER SETTINGS ................................................................................................. 34 
7.8 FACTORY CALIBRATION............................................................................................................ 35 
8 DATA UPLOAD ................................................................................................................................... 35 
9 INFORMATION................................................................................................................................... 35 
9.1 SYSTEM INFORMATION............................................................................................................. 35 
9.2 FIRMWARE UPDATE................................................................................................................... 36 
9.3 SYSTEM DIAGNOSTICS.............................................................................................................. 36 
9.4 MAINTENANCE ........................................................................................................................... 37 
9.5 SEARCH LOG................................................................................................................................ 37 
10 ACCESS LOG...................................................................................................................................... 38 
READ ID CARD.......................................................................................................................................... 41 
(MODEL BS-DET2000BTRF) ........................................................................................................................ 41 
 
 

1. PRODUCT OVERVIEW

1.1 INTRODUCTION TO THE PRODUCT

The DET2000BT device is a terminal that provides face detection, forehead temperature detection,

face mask detection and other basic functions. The device can be widely used in the realization of

access control, presence, safety of public and work environments

1.2 PRODUCT CHARACTERISTICS

•The Linux operating system used has a significant advantage over the Android system in

terms of reliability and stability. The video stream produced is in H264 format with ONVIF

protocol for easier management from other devices, a complete function of face

acquisition, recognition and temperature measurement.

•Abnormal body temperature alarm: non-contact body temperature detection within 1

second, the measurement distance is 25 - 50 cm, temperature margin of error of ± 0.3 ℃,

connection with external sound and light alarms.

•Integrated identity card + dual IC card identification module (on BS-DET2000BTRF model),

can achieve 1: 1, 1: N comparison mode

•Face recognition within a distance of 0.3 - 1.5 meters, the face can be recognized and

registered

•Facial recognition technology based on an improved multi-task cascade convolutional

neural network, adopted to reduce the image quality requirement and significantly

improve face detection speed

•It uses a deep learning algorithm, supports the storage of 10,000 faces in the database

•Supports local access to query and configure device parameters, view real-time monitoring

and face comparison results

•Flexible import of face data, support for importing individual batch files and importing

snapshots in real time

•Support of the "white list", "black list", "visitors", etc ...

•Voice notification after each detection

•Supports storage on the TF card (optional), can store 10,000 acquisition and face

recognition records.

•Equipped with RS485 output, alarm I / O, wiegand port and other interfaces

1.3 FIELDS OF APPLICATION

The device can find application in multiple sites such as:

•Schools

•Offices

•Shops

•Hospitals

•Nursing homes

•Corporate

•Nursing homes

•Municipal offices

And in any other place where it may be necessary to check the body temperature at the entrance.

The device can be used both standalone and integrated in existing access control systems thanks to the

communication ports it is equipped with (LAN, 485, Wiegand) and the possibility of providing SDK and API.

2. PRODUCT INSTALLATION

2.1 INSTALLATION

This equipment can be installed on access turnstiles. Before installation, it is necessary to make sure that

the top cover plate has been perforated with the size of the hole corresponding to the diameter of the

device support.

2.2 INSTALLATION ON DETPAV110 PEDESTAL

•Footboard

•Tube

•Nut for pipe fixing

• Insert the nut for fixing the tube inside the hole in the platform, so that the part to be screwed is

facing upwards, then insert the nut from the bottom of the platform.

• Screw the tube with the fixing nut: the tube must be screwed with the hole facing downwards

• Insert the washer with the conical part facing downwards.

• Screw the device to the pipe together with the washer positioned

2.3 INSTALLATION ON DETBASE TABLE BASE

To install the device on the DETBASE desk base:

• Insert the device into the hole in the b ase

• Insert the gasket (1), the washer (2) and screw everything with the ring nut (3)

Indice

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente