Bosch Readykey X UDS-10 Manuale utente

17553v1.0

Jan 08

UDS-10 / UDS-1100 Serial Tunnel on CNC

Setup Guide

2 17553v1.0

Table of Contents

1. Introduction..............................................................................................................................3

2. Installation................................................................................................................................3

3. Configuration...........................................................................................................................4

3.1 DeviceInstaller Configuration...............................................................................................4

3.2 Telnet Configuration ............................................................................................................7

3.2.1 Connecting to the UDS...............................................................................................7

3.2.2 UDS to PC Configuration ...........................................................................................7

3.2.3 PC to Door Controller Configuration ..........................................................................9

3.3 Testing Network Connectivity............................................................................................10

4. Configuring the Door Controller..........................................................................................11

5. Configuring the Channel.......................................................................................................11

17553v1.0 3

1. Introduction

Using UDS-10s or UDS-1100s, a CNC channel to K2100 / K2200 Door Controllers can be set up to

communicate over an Ethernet network.

Using a method called serial tunneling, two UDS-10s or UDS-1100s encapsulate serial data into packets and

transports them over the network.

Note

If replacing pIPer Serial Ethernet units, the pIPers at both ends must be replaced with UDS devices.

2. Installation

UDS #1 is connected to a serial port on the PC / CNC. A standard 9-way to 25-way serial cable can be used.

UDS #2 is connected to the serial port on the first door controller. The serial lead can be supplied (part no.

12090). Alternatively, a K2200IP that has an inbuilt UDS can be used.

4 17553v1.0

3. Configuration

Each UDS is configured using the DeviceInstaller program supplied by Lantronix.

IMPORTANT

1. It is an absolute requirement for the error free operation of the UDS that static IP addresses are

used.

2. The DeviceInstaller program must be run on the same subnet as the UDS device. For example, if

there is a router between the PC running DeviceInstaller and the UDS then the configuration

process will not work.

3.1 DeviceInstaller Configuration

Notes

1. The procedure carried out in this section has to be performed before Telnet Configuration (see

Section 3.2) can be carried out.

2. Make a note of the MAC Address of the UDS (printed on the underside of the UDS or on the cover

above the IP unit of the K2200IP).

3. Consult your IT department to determine the IP Address and the PC Network Class for the UDS.

Procedure

1. Run the DeviceInstaller program and the DeviceInstaller window is displayed:

2. Select and the Assign IP Address window is displayed:

3. Enter the MAC Address of the UDS, IP Address to be assigned, and PC Network Class.

4. Select the Set IP Address and the Information window is displayed:

17553v1.0 5

5. Select the OK button and the and the DeviceInstaller window is redisplayed:

6. Select (Search the network for devices) and the Search Network window is displayed:

7. Select the PC Network Class

8. Select the Start Search button and any UDS devices on the network will be displayed.

9. Select the Save button and the DeviceInstaller window is redisplayed with a list of all UDS devices

detected:

6 17553v1.0

10. Select the required device.

11. Select Tools > Device Manager and the Device Management window is displayed:

12. Select (Telnet to Device) and a Telnet session will then start.

The DeviceInstaller part of the UDS configuration is complete, the next part is using Telnet.

17553v1.0 7

3.2 Telnet Configuration

3.2.1 Connecting to the UDS

The UDSs can be connected outside of the DeviceInstaller by using Windows Telnet. To do this, connect

using the unit’s assigned IP Address and a port number of 9999. For example: use the command TELNET

192.168.101.52 9999 at the command prompt.

Notes

1. In the following example, text enclosed in a gray box represents the screen display of whatever

application is hosting the Telnet session.

2. Bold text in the gray box represent example values.

3. This is an example configuration with no gateway. If a gateway is required on a specific network, it

should be configured on the relevant gateway.

When Telnet has connected to the UDS, the following (or similar) is displayed:

*** Lantronix Universal Device Server ***

Serial Number 5423446 MAC address 00:20:4A:54:5B:96

Software Version V04.2 (000908)

Press Enter to go into Setup Mode

Press Enter.

Hardware: Ethernet Autodetect

IP addr 192.168.31.202, no gateway set,netmask 255.255.255.000

***************** Security *****************

Telnet setup is enabled

TFTP download is enabled

Port 77FEh is enabled

Web Server is enabled

Enhanced password is disabled

***************** Channel 1 *****************

Baudrate 9600, I/F Mode 4C, Flow 00

Port 10001

Datagram Type 01

Pack Cntrl: 00

Remote IP Adr: 192.168.004.243, Port 00000

Change Setup : 0 Server configuration

1 Channel 1 configuration

6 Security

7 Factory defaults

8 Exit without save

9 Save and exit Your choice ?

3.2.2 UDS to PC Configuration

This section describes the configuration of the UDS for network operation.

Configuration

From the main menu (displayed above) type 0 (for the option Server Configuration) and press Enter.

IP Address : (000) 192.(000) 168.(000) 101.(000) 27<enter>

Set Gateway IP Address (Y) Y<enter>

Gateway IP addr (000) 192.(000) 168.(000) 101.(000) 254<enter>

Netmask: Number of Bits for Host Part (0=default) (00) 8<enter>

Change telnet config password (N) N<enter>

8 17553v1.0

Enter the following information:

IP Address The IP Address displayed will be the one that was entered in

Section 3.1. Do not change this value; press Enter to move onto

the next step.

Set Gateway Address Press the Ykey, and press Enter.

Gateway IP Addr Enter the gateway IP address and press Enter.

Netmask The subnet mask (‘netmask’) is entered in an unusual fashion. The

prompt asks for the number of bits. For example, 255.255.255.0

corresponds to 8 bits. See the table below for other examples.

Mask Bits

255.0.0.0 24

255.255.0.0 16

255.255.240.0 12

255.255.248.0 11

255.255.254.0 9

255.255.255.0 8

255.255.255.128 7

255.255.255.192 6

255.255.255.224 5

255.255.255.240 4

255.255.255.248 3

Change telnet config

password Press the N key and press Enter.

The basic parameters menu will be displayed:

*** basic parameters

Hardware: Ethernet Autodetect

IP addr 192.168.004.241, no gateway set,netmask 255.255.255.000

***************** Channel 1 *****************

Baudrate 9600, I/F Mode 4C, Flow 00

Port 10001

Datagram Type 01

Pack Cntrl: 00

Remote IP Adr: 192.168.004.147, Port 00000

Change Setup : 0 Server configuration

1 Channel 1 configuration

7 Factory defaults

8 Exit without save

9 Save and exit Your choice ?

17553v1.0 9

3.2.3 PC to Door Controller Configuration

After completing Section 3.2.2, the UDS needs to be configured to communicate with the PC.

Configuration

From the basic parameters menu (see previous section) select 1and press Enter.

Baudrate (9600) 9600 <enter>

I/F Mode (4C) ? 4C <enter>

Flow (00) ? 00 <enter>

Port No (10001) ? nnnnn <enter>

ConnectMode (C0) ? Cn <enter>

Datagram Type (00) ? 01 <enter>

Remote IP Address : (000) 192. (000) 168. (000) 101. (000) 3 <enter>

Remote Port (00000) ? 00000 <enter>

Pack Cntrl (00) ? 00 <enter>

SendChar 1 (00) ? 00 <enter>

SendChar 2 (00) ? 00 <enter>

Enter the following information:

Baudrate Press Enter to accept the default value.

I/F Mode Press Enter to accept the default value.

Flow Press Enter to accept the default value.

Port No Enter the port number and press Enter.

ConnectMode Enter the connect mode for the administration software and press Enter.

Datagram Type Enter the value 01 and press Enter.

Remote IP Address Enter IP address of the PC and press Enter.

Remote Port Press Enter to accept the default value.

Pack Cntrl Press Enter to accept the default value.

SendChar 1 Press Enter to accept the default value.

SendChar 2 Press Enter to accept the default value. The menu will now be displayed again.

Change Setup : 0 Server configuration

1 Channel 1 configuration

7 Factory defaults

8 Exit without save

9 Save and exit Your choice ?

Select 9(Save and Exit) and press Enter. Configuration of the UDS is now complete.

10 17553v1.0

3.3 Testing Network Connectivity

To test if the UDS is accessible over the network:

1. Run the DeviceInstaller program.

2. Select the (Ping Device)and the Ping Device window is displayed:

3. Enter the IP Address of the unit to be pinged, and select the (Ping Device).

Successful pinging will be indicated by text similar to that displayed.

Note

Do not attempt to set up the door controller within application software until you have established that the

PC can “see” the UDS over the network.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Bosch Sistema di controllo

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Bosch

Bosch rexroth HS5E Manuale utente

Bosch

Bosch Security Escort SE2000 Series Manuale del prodotto

Bosch

Bosch rexroth SYDFE1 2X Series Manuale utente

Bosch

Bosch Rexroth IndraMotion MLD Series Istruzioni per l’uso

Bosch

Bosch rexroth IndraDrive Mi KMV03 Manuale utente

Bosch

Bosch Rexroth IndraMotion MTX 09VRS Manuale utente

Bosch

Bosch Rexroth IndraDrive Mi KCU02 Manuale utente

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Bosch

Bosch rexroth ctrlX AUTOMATION Manuale utente

Bosch

Bosch rexroth SYDFED 2X Series Manuale utente

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Bosch

Bosch FHP UPM I Manuale utente

Bosch

Bosch Rexroth IndraMotion MTX 11 VRS Istruzioni per l’uso

Bosch

Bosch Rexroth IndraMotion MTX micro Guida rapida

Bosch

Bosch Rexroth IndraDrive Mi KCU01 Manuale utente

Bosch

Bosch LTC 8900 Series Manuale utente

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Bosch

Bosch BDU3320 Manuale utente

Bosch

Bosch FHP UPM II Manuale utente

Bosch

Bosch Rexroth IndraControl XM21 Manuale utente

Bosch

Bosch Rexroth CS351 Manuale utente

Bosch

Bosch Rexroth NYCe 4000 Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente