Bosch D7039 Manuale utente

D7039

Installation Guide

Multiplex Expansion

Module

Bosch | 09/05 | 38685F2

D7039 | Installation Guide |

Notices

Use these instructions to install the D7039 Multiplex

Expansion Module in a fire system supervised by a

D7024 Fire Alarm Control Panel (FACP).

Install, test, and maintain the D7039 according to these

instructions, NFPA 72, local codes, and the Authority

Having Jurisdiction (AHJ).

Follow the procedures in this document to

avoid personal injury and damage to the

equipment. Failure to follow these

procedures can cause the D7039 to not

operate properly. Bosch is not responsible

for improperly installed, tested, or maintained

devices.

For the D7039 with ROM version 1.04 to

operate properly, the D7024 FACP must be

running version 2.05 or later firmware.

1.0 Description

The D7039 (Figure 1) connects directly to the FACP for

either two Class B multiplex buses or one Class A

multiplex bus that allows up to 247 remote points.

When configured for Class A operation,

the D7039 can only support Addresses 9

through 128.

Notices

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

Histo ry

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - D7024 Control Board

2 - Enclosure

3 - I/O module for the D7039

4 - D7039 Module

Figure 1: D7039 Module Location

3Bosch | 09/05 | 38685F

D7039 | Installation Guide | 2.0 Installation

2.0 Installation

Failure to follow the mounting instructions in this document can damage the FACP.

The D7039 and D7024 have static sensitive components and must be handled with care. Follow the

anti-static procedures when handling these modules.

Before installing the D7039 Module, remove all AC and battery power to the FACP.

1. If the D7024 is already installed in an enclosure, remove it.

2. Place the FACP on a flat surface with the component side facing up (Item 2 in Figure 2).

3. Insert the four plastic standoffs in the mounting holes (Item 3 in Figure 2) without bending or flexing the FACP.

4. Align the standoff tabs so they do not touch the module components.

5. Firmly press the standoffs into the board, allowing the ears to expand out.

6. Mount the D7039 on the standoffs, ensuring the FACP connector pins (Item 4 in Figure 2) are properly aligned.

7. Install the FACP in the enclosure.

8. Use the mounting screw (Item 5 in Figure 2) to secure the D7039’s ground wire (Item 6 in Figure 2) to the FACP.

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

History

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - D7039 Module 4 - FACP connector pins to align with the D7039

2 - D7024 FACP 5 - Mounting screw

3 - Standoff mounting holes (4) 6 - Ground wire

Figure 2: Mounting the D7039 on the D7024

Bosch | 09/05 | 38685F4

D7039 | Installation Guide |

9. Mount the D7039 I/O Module (Item 1 in Figure 3) in the FACP enclosure (Item 2 in Figure 3) using the mounting

holes in the enclosure (Item 3 in Figure 3).

10. Connect the yellow and green earth ground wire from the I/O module to the earth ground terminal on the

FACP control board (Item 4 in Figure 3).

3.0 Wiring

1. Connect the D7039 multiplex loop using up to 3800 ft (1170 m) of 18 AWG (1.0 mm2) or 5950 ft (1810 m) of

16 AWG (1.5 mm2) wire (Figure 4). Do not use shielded wire.

Do not use shielded wire. Twisted pair is acceptable, but is not recommended.

2.0 Installation

Figure 4: Connecting the Mux Class “A” and Class “B”

1 - I/O module for the D7039, wired Class “A” 4 - Mux B Addresses 129 through 255

2 - Class “A” Addresses 9 through 128 5 - Mux A Addresses 9 through 128

3 - I/O module for the D7039, wired Class “B”

Note: All terminals are supervised.

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

History

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - I/O module 3 - Holes (3) and standoffs (3) to mount the I/O module

2 - Enclosure 4 - I/O module earth ground wire to the D7024 terminal connection

Figure 3: Installing the Input-Output Module

5Bosch | 09/05 | 38685F

D7039 | Installation Guide | 4.0 Specifications

Figure 5: Measuring Class “B” Loop Resistance

1 - 50

Ω

maximum 2 - Mux bus wires 3 - Clip lead

Figure 6: Measuring Class “A” Loop Resistance

1 - 50

Ω

maximum 2 - Mux bus wires 3 - Clip lead

You can configure the D7039 with a single fault tolerant Class “A” loop or as a pair of supervised Class “B”

loops. When configured as a Class “A” loop and installed on a D7024 Control Panel before Lot #100, the

D7039 implements a Style 4.5 signaling line circuit (SLC). When installed on a D7024 Control Panel Lot #100

or later, the D7039 implements Style 6 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499)

for programming.

When configured as a Class “B” loop and installed on a D7024 Control Panel before Lot #100, the D7039

implements a Style 3.5 SLC. When installed on a D7024 Control Panel Lot #100 or later, the D7039

implements a Style 4 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499) for programming.

2. Measure loop resistance by shorting the end of the farthest device in Class “B” (Figure 5) or shorting the return

wire in Class “A” (Figure 6) and reading the total resistance of all wires associated with the loop.

3. Ensure the loop is disconnected from the D7039 Module.

Bosch | 09/05 | 38685F6

D7039 | Installation Guide |Notes

4.0 Specifications

Table 1: Specifications

Input Voltage 24 VDC nominal from FACP

Current Draw, Standby

and Alarm

150 mA maximum

Current Draw Load 100 mA maximum for each bus

Maximum Bus Voltage 8.5 V to 13 V

Maximum Wiring

Resistance

50 Ω, Class A (Style 6) or Class B (Style 4) SLC

Environment Indoor/dry

Note: All Mux Bus terminals are power-limited and supervised.

7Bosch | 09/05 | 38685F

D7039 | Installation Guide | Notes

Notes

Bosch

130 Perinton Parkway

Fairport, NY 14450-9199 USA

Customer Service: (800) 289-0096

Technical Support: (888) 886-6189

38685F

Indice

Altri manuali Bosch Unità di controllo

Bosch

Bosch DDC KIT Manuale utente

Bosch

Bosch ISM 1 Manuale utente

Bosch

Bosch OMNEO OM-1 Manuale utente

Bosch

Bosch CFB 840 Guida utente

Bosch

Bosch FM441/CMM 910 Manuale utente

Bosch

Bosch PAVIRO PVA-1WEOL Manuale di installazione e funzionamento

Bosch

Bosch Rexroth M4-12 Istruzioni operative

Bosch

Bosch VCU MS 50.4P Manuale utente

Bosch

Bosch C900TTL-E Manuale utente

Bosch

Bosch ConnectModule BCM3100 Manuale utente

Bosch

Bosch FLM-420-EOL2W-W Manuale utente

Bosch

Bosch Rexroth WMM6 Series Manuale utente

Bosch

Bosch KTS Truck Manuale utente

Bosch

Bosch Rexroth BVD 52 Series Manuale utente

Bosch

Bosch DS7400 Manuale utente

Bosch

Bosch D8125 Guida rapida

Bosch

Bosch FM443/CMS 910 Manuale utente

Bosch

Bosch Rexroth RE 07601-B Manuale utente

Bosch

Bosch ECU MS 25 Sport Manuale utente

Bosch

Bosch ICP-COM-IF Manuale utente

Bosch

Bosch rexroth Automax 100 Manuale utente

Bosch

Bosch KTS 5a Series Manuale utente

Bosch

Bosch Rextroth Indramat RECO R-IB IL CNT Istruzioni per l’uso

Bosch

Bosch Professional GCY 42 Istruzioni per il montaggio

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente