Bosch MS 3 Sport GT3 Cup Manuale utente
Engine Control Unit MS 3 Sport GT3 Cup
Manual
Version 1.2 17/04/2019
Content
ii/24 Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual Bosch Motorsport
Content
1 Getting started ................................................................................................................................................................ 3
2 Sport Systems - Overview.............................................................................................................................................. 4
3 Technical Data................................................................................................................................................................. 5
3.1 Input channels ....................................................................................................................................................................................................... 5
3.2 Output channels.................................................................................................................................................................................................... 5
3.3 Power supply.......................................................................................................................................................................................................... 7
3.4 Ignition trigger wheel ......................................................................................................................................................................................... 8
3.5 Sensor recommendation ................................................................................................................................................................................... 11
4 Starting up the ECU ........................................................................................................................................................ 12
4.1 Offline Data Application .................................................................................................................................................................................... 12
4.2 Online Data Application..................................................................................................................................................................................... 18
4.3 Activation of Software Options....................................................................................................................................................................... 21
5 Extensibility ..................................................................................................................................................................... 22
Getting started | 1
Bosch Motorsport Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual 3/24
1 Getting started
Disclaimer
Due to continuous enhancements we reserve the rights to change any illustrations, photos
and technical data within this manual. Please retain this manual for your records.
Before starting
Before starting your engine for the first time, install the complete software from the in-
stallation CD. Bosch Motorsport software is developed for Windows 2000/XP. Connect the
PC Link Adapter (MSA Box II) or the Ethernet line (depending on calibration equipment) to
your computer and install the driver. Read the manual carefully and follow the application
hints step by step. Don’t hesitate to contact us, contact data can be found on the back
side of this document.
NOTICE
The Bosch Motorsport MS 3 Sport GT3 Cup was developed for use by professionals and
requires in depth knowledge of automobile technology and experience in motorsport. Us-
ing the system does not come without its risks.
It is the duty of the customer to use the system for motor racing purposes only and not
on public roads. We accept no responsibility for the reliability of the system on public
roads. In the event that the system is used on public roads, we shall not be held respons-
ible or liable for damages.
Any maintenance or repair must be performed by authorized and qualified personnel ap-
proved by Bosch Motorsport.
2 | Sport Systems - Overview
4/24 Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual Bosch Motorsport
2 Sport Systems - Overview
The Sport Systems support an easy to understand user concept. The MS 3 Sport GT3 Cup
is configured as an alpha/n version. This means that the engine characteristic map is
based on engine speed, throttle position and engine temperature. The injected amount of
fuel and the ignition point are derived from these values.
The drawing gives you an overview over the essential input and output channels of a MS 3
Sport GT3 Cup that are necessary to run the engine.
Engine Control Unit
Camshaft teeth sensor
Crankshaft teeth sensor
Lambda sensor
Throttle valve position potentiometer
Fuel temperature sensor
Engine oil temperature sensor
Ambient pressure sensor
Intake air temperature sensor
Knock sensor
Accelerator pedal sensor
(only with Egas)
. . .
Input signals Output signals
Power supply
Fuel injectors A-F
Ignition coils A-F
Electronic throttle
body (only with Egas)
. . .
Illustration1: Input and output channels
Technical Data | 3
Bosch Motorsport Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual 5/24
3 Technical Data
3.1 Input channels
Input channels for temperature sensors
Temperature inputs have an internal “pull up” resistor for use with a NTC sensor (negative
temperatur coefficient). These pull ups can be switched software specifically. Depending
on the used sensor (e.g. 15 kOhm or 2.5 kOhm NTC) the corresponding linearization curve
has to fit.
For example
– tmot (engine temperature)
– tair (intake air temperature)
Input channels for voltage sensors
For measuring of throttle positions or pressures which deliver a voltage (active sensors),
pull up resistors are not necessary. These sensors must be calibrated with the sensors off-
set and sensitivity values (printed on the sensor, if it is from Bosch).
For example
– ath (throttle position)
– pfuel (fuel pressure)
– poil (oil pressure)
Input channels for inductive speed sensors
In the default configuration the MS 3 Sport GT3 Cup needs an inductive speed sensor on
the ignition trigger wheel.
Input channels for Hall-effect-speed sensors
For the camshaft signal a Hall-effect sensor is necessary. Also for wheel speed measure-
ment Hall-effect sensors are recommended. Four Hall-effect wheel speed sensors can be
connected directly to the ECU. Different hardware configurations are available on request.
Input channels for Lambda measurement and control
For wide range Lambda measurement and control we recommend a Lambda sensor of the
Bosch LSU series.
3.2 Output channels
There are 6 independent injection output stages for the injection. These injection output
stages can take a maximal current of 2.2 Ampere. Therefore the injection valves must have
a resistance of at least 6 Ohm.
NOTICE
Don’t use Bosch injection valves with 1.2 Ohm.
A few Bosch injection valves have an internal resistance of just 1.2 Ohm. These types can
not be used here.
3 | Technical Data
6/24 Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual Bosch Motorsport
The MS 3 Sport GT3 Cup has integrated ignition power stages. The wiring is shown in the
following picture.
Illustration2: Integrated ignition power stage
NOTICE
In case of ignition-caused malfunctions, please use screened sensor wires.
A typical 6 cylinder engine with firing order 1-5-3-6-2-4 is connected as follows:
Firing 1 5 3 6 2 4
IGN A B C D E F
INJ A B C D E F
There are max. 6 independent injection output stages for the injection. These injection
output stages can take a maximal current of 2.2 Ampere. Therefore the injection valves
must have a resistance of at least 6 Ohm.
NOTICE
Don’t use Bosch injection valves with 1.2 Ohm.
A few Bosch injection valves have an internal resistance of just 1.2 Ohm. These types can
not be used here.
The MS 3 Sport GT3 Cup has integrated ignition drivers. The wiring is shown in the follow-
ing picture.
Illustration3: Integrated ignition drivers
Technical Data | 3
Bosch Motorsport Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual 7/24
NOTICE
In case of ignition-caused malfunctions, please use screened sensor wires.
A typical 6 cylinder engine with firing order 1-5-3-6-2-4 is connected as follows:
Firing 1 5 3 6 2 4
IGN A B C D E F
INJ A B C D E F
3.3 Power supply
The MS 3 Sport GT3 Cup requires an external main relay to be wired to the harness. This
relay is controlled by the MS 3 Sport GT3 Cup to realize that important information can be
stored after switching off the ignition.
Please ensure that you have a good ground installation. That means:
– A ground that has a solid, low resistance connection to the battery minus terminal
– Connection should be free from dirt, grease, paint, anodizing, etc.
– Cylinder heads make a good grounding point
– Use large diameter wire.
– More metal-to-metal contact is better
Connection of the power supply
The following notations for power signals are used:
– KL15 is a switched battery rail controlled by the ECU driver.
– KL30 is an unswitched battery positive rail (same as battery positive terminal).
– KL31 is an unswitched ground rail (same as battery negative terminal).
3 | Technical Data
8/24 Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual Bosch Motorsport
85
30
87a
87
86
Bosch Automotive relay
Fuse / Circuit breaker
KL30
KL15
To battery plus (+)
Master kill switch
Ignition switch
Notes:
- ECU requires a dedicated relay to be installed in the car
- KL30 is HAAT (Hot At All Times)
- KL15 is hot only when ECU engages relay
- ECU will engage relay after 12V is detected on pin ‘J’ by pulling pin ‘B’ to ground
- ECU will disengage the relay after 12V is removed from pin ‘J’,
but may be delayed for up to 2 seconds after engine speed signal is zero.
- It is recommended to fuse the KL30 circuit
- Wire gauge recommendations based on Raychem Spec 44 wire
KL30
KL15
KL15 IN
Main relay
KL31
KL31
To battery minus (-)
14ga
20ga
20ga
14ga
20ga
20ga
20ga
16ga
16ga
16ga
16ga
14ga
14ga
F
H
B
C
G
L
M
J
Spec
harness
connector
ECU
Illustration4: Power supply connection plan
CAUTION
Wrong polarity / high currents
Wrong polarity of the terminals and high currents damage the MS 3 Sport GT3 Cup. Be
careful to observe current limits of wires and connector pins!
3.4 Ignition trigger wheel
To start the engine, the ECU requires information about the position of the camshaft and
crankshaft. These are determined by using sensors on the cam and crankshaft generator
gear.
In this chapter you’ll find the sensors you need to detect the camshaft and crankshaft pos-
ition and how to tune the components to each other.
3.4.1 Camshaft and Crankshaft Sensors
Camshaft trigger sensor
The camshaft trigger sensor is a Hall-effect type with a single tooth trigger wheel. Bosch
Motorsport recommends the use of Hall-effect sensor HA-P.
Illustration5: Camshaft wheel
Technical Data | 3
Bosch Motorsport Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual 9/24
Crankshaft trigger sensor
The software assumes a 36-2 teeth or a 60-2 teeth trigger wheel for proper operation. The
type can be choosen in the software Modas Sport. The crankwheel trigger sensor must be
an inductive type for default configuration. Bosch Motorsport recommends the use of in-
ductive speed sensor IA-C. The picture below shows the correct installation position.
tooth count 60 (-2)
diameter > 100 mm
diameter 3.5 mm
gap depth h1/2
air gap 0.8 ± 0.3 mm
wheel thickness > 5.0 mm
TDC to REF free adjustable
gap width 3.30°
tooth width 2.70°
Description Nominal Dimension
tooth count 36 (-2)
diameter > 95.3 mm [3.750 in]
diameter 5.0 mm [0.197 in]
gap depth h1/2
air gap 0.8 ± 0.3 mm
wheel thickness > 5.0 mm [0.197 in]
TDC to REF free adjustable
gap width 5.55°
tooth width 4.45°
Description Nominal Dimension
Illustration6: Crankshaft wheel
Further requirements
– The Trigger sensor must be made of a ferromagnetic material.
– The Sensor wheel teeth must be sharp.
– The Reference mark is the second tooth after the gap.
3.4.2 Mounting of the Sensors
Procedure to find the right position for the crank and cam triggers:
1. Rotate the engine to the precise position of TDC compression for cylinder#1.
2. Rotate the engine (*) crankshaft degrees backwards.
3. Adjust the position of the crank trigger wheel in reference to its inductive speed
sensor: the longitudinal axis of the sensor must point exactly towards the reference
mark (2nd falling edge after the gap).
4. Adjust the position of the cam trigger in reference to its Hall Effect speed sensor: the
sensor must be about at the centre of the tooth.
5. Turn the engine by 360 crankshaft degrees to reach the position of (*)° before TDC
exhaust for cylinder#1.
6. Verify that the crank trigger reference mark is in alignment with the longitudinal axis
of the sensor (same as Step 3) and that the cam trigger tooth is at the opposite side
of its speed sensor.
3 | Technical Data
10/24 Engine_Control_Unit_MS_3_Sport_GT3_Cup_Manual Bosch Motorsport
(*)
360°360°
(*)
720°
TDC compression
for cylinder #1
TDC exhaust
for cylinder #1
TDC compression
for cylinder #1
60-2 tooth crank
trigger wheel
cam trigger wheel,
cylinder #1 position
Reference mark
gap
2nd falling edge
after the gap
Direction of
wheel travels
Position of the
speed sensors
(*)° before TDC compression for cyl. #1 , the tooth on the
cam trigger must overlap the reference mark of the crank
trigger (= 2nd falling edge).
(*)° before TDC exhaust for cyl. #1 , the tooth at the cam
trigger must NOT overlap the reference mark of the crank
trigger.
gap gap
2nd falling edge
after the gap
(*)
(*): OT1ANGLE_SYS
Illustration7: Position of the sensors
– All angles are shown and indicated in crankshaft degrees.
– The width of the cam trigger tooth is not important; however it must be wide enough
to ensure a safe overlap of the crank trigger reference mark at any time.
– The Hall-effect signal is the inversion of the shape of its cam trigger: the tooth effects
a 'low' signal at the sensor and vice versa.
– With 4 and 6 cylinder engines, the value of 66 degrees must be replaced by 78 de-
grees.
Indice
Altri manuali Bosch Unità di controllo
Bosch
Bosch OMNEO OM-1 Manuale utente
Bosch
Bosch Rexroth II 3G Manuale utente
Bosch
Bosch ISP-EMIL-120 Manuale utente
Bosch
Bosch Rexroth H-4WEH...XE Series Manuale utente
Bosch
Bosch Control 8311 Manuale utente
Bosch
Bosch DS7432 Manuale utente
Bosch
Bosch Rextroth Indramat RECO R-IB IL CNT Istruzioni per l’uso
Bosch
Bosch DS7400 Manuale utente
Bosch
Bosch Rexroth MKK 12-40 Manuale utente
Bosch
Bosch Rexroth IndraControl S67 Series Guida utente
Bosch
Bosch Rexroth BTV 16 Manuale tecnico
Bosch
Bosch POPEX B299 Manuale utente
Bosch
Bosch ECU MS 25 Sport Manuale utente
Bosch
Bosch Rexroth 4WRPD Manuale utente
Bosch
Bosch FLM-420-I2-E Manuale utente
Bosch
Bosch Conettix DX4020 Manuale utente
Bosch
Bosch Rexroth R-IB IL 24 PSDO 8-PAC Manuale utente
Bosch
Bosch Rexroth VKK Series Manuale utente
Bosch
Bosch Rexroth NYS04.1-ST-01-LMS-SERCOS-NY4078 Manuale utente
Bosch
Bosch Rexroth NYCe 4000 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
