BRAYER BR4951 Manuale utente
Instruction manual
Инструкция по эксплуатации
Fan BR4951
Вентилятор BR4951
brayer.ru
СОДЕРЖАНИЕ
EN......................................................................................................................................3
DE....................................................................................................................................12
RU ...................................................................................................................................21
KZ....................................................................................................................................30
3
EN
FAN BR4951
The fan is intended for articial ventilation of the
room.
DESCRIPTION
1. Base
2. Water level scale
3. Body
4. Outgoing airow grid
5. Display
6. Control panel
7. Water tank lid/cool pack installation place
8. Detachable air inlet grid
9. Grid clamps
10. Carrying handle
Control panel (6)
11. On/o button «ON/OFF»
12. Airow type selection button «WIND»
13. Fan body oscillation on/o button «OSC»
14. Cool shot on/o button «COOL»
15. Timer on/o button «Timer»
16. Airow speed selection button «SPEED»
Display (5)
17. Airow speed symbols « ,,»
18. Timer operation time/air temperature digits
EN
ATTENTION!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA into the mains. To install
RCD, contact a specialist.
19. Airow type symbol « »
20. Night mode icon « »
21. Timer on symbol « »
22. Cool shot function symbol « »
23. Remote control
24. On/o button «ON/OFF»
25. Airow speed selection button «SPEED»
26. Timer on/o button «Timer»
27. Cool shot on/o button «COOL»
28. Airow type selection button «WIND»
29. Fan body oscillation on/o button «Oscillator»
30. Battery holder
4 EN
1
2
8
7 17 20
19
18
21
12 15
11
13
16
14
9
10
3
4
5
6
5EN
Рiс. 4
Рiс. 6
Рiс. 2
Рiс. 3
Рiс. 5
Рiс. 1
24 27
25 28
26 29
30
23
6
EN
SAFETY MEASURES AND OPERATION
RECOMMENDATIONS
Read the operation manual carefully before using
the fan; after reading, keep it for future reference.
• Use the unit for its intended purpose only, as it is
stated in this manual.
• Mishandling the unit can lead to its breakage and
cause harm to the user or damage to the user’s
property, which is not covered by warranty.
• Do not use the power cord as a carrying handle for
the fan.
• Do not wind the power cord around the fan body.
• Provide that the power cord does not contact with hot
surfaces and sharp furniture edges.
• Protect the unit from impacts, falling, vibrations and
other mechanical stress.
• Avoid blocking the air inlet grid of the fan with foreign
objects, do not cover the unit during the operation.
• Do not use the unit in places where inammable
liquids are used or aerosols are sprayed, do not use
the unit in the places where such liquids are stored.
• Do not use the unit near heating appliances, heat
sources or open ame.
• Do not use the unit outdoors, in bathrooms or in
places with high humidity.
• Do not use the unit in proximity to the kitchen sink,
near swimming pools or other containers lled with
water.
• If the unit is dropped into water, unplug it
immediately, and only then you can take the unit out
of water. Apply to the authorized service center for
testing or repairing the unit.
• Do not touch the unit body, the power cord and the
power plug with wet hands.
• It is not recommended to use the unit during lightning
storms.
• Do not block the fan grids and do not insert foreign
objects onto them.
ATTENTION! A lithium battery is used in the remote
control. To avoid danger, do not allow children to play
with the battery. If your child swallowed a battery,
immediately see your doctor.
• Make sure that the operating voltage of the unit
indicated on the label corresponds to your home
mains voltage.
• Place the fan vertically on a at dry moisture- and
heat-resistant surface, do not place it horizontally and
do not turn it over.
• Do not place the fan on soft surfaces, such as
carpets with high pile, sofas or beds.
• Do not place the fan near curtains and do not direct it
to house plants.
• Do not use the fan in a limited space, for example, in
built-in cabinets or wall niches.
• It is not recommended to stay in the zone of the air
ow from the fan for a long period of time, especially
for children and the elderly.
7
EN
• Never leave the unit connected to the mains
unattended.
• Unplug the unit after usage or before cleaning.
• Switch the fan o and unplug the power cord plug
from the mains socket.
• When unplugging the unit, hold the power plug and
carefully remove it from the mains socket, do not pull
the power cord, as this can lead to its damage or
cause a short circuit.
• Do not immerse the unit into water or any other
liquids.
• If water droplets fall on the fan body, switch it o and
disconnect the power plug from the mains before
touching the unit, then wipe the fan body with a dry
cloth.
• For child safety reasons do not leave polyethylene
bags used as packaging unattended.
ATTENTION!
Do not allow children to play with polyethylene bags
or packaging lm. Danger of suocation!
• During the unit operation and breaks between
operation cycles, place the unit out of reach of
children.
• The unit is not intended for usage by physically or
mentally disabled persons (including children) or by
persons lacking experience or knowledge if they are
not under supervision of a person who is responsible
for their safety or if they are not instructed by this
person on the usage of the unit.
• From time to time check the power cord integrity.
• If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not
disassemble the unit by yourself, if any malfunction
is detected, and after the unit was dropped, unplug it
and apply to the service center.
• To avoid damages, transport the unit in the original
package.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, DO NOT USE THE UNIT FOR COMMERCIAL
OR LABORATORY PURPOSES.
• The unit is not intended for usage by children.
• Do not leave children unattended to prevent using
the unit or the cool pack as a toy.
• Do not allow children to touch the operating surface,
the unit body, the power cord or the power plug
during operation of the unit.
• Be especially careful if children or disabled persons
are near the operating unit.
8
EN
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative
temperature, unpack it and wait for at least 3 hours
before using it.
• Unpack the unit and remove all the packaging
materials.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do
not plug it into the mains.
• Make sure that specied specications of power
supply voltage of the unit correspond to the
specications of your mains. When using the unit in
the mains with 60 Hz frequency, the unit does not
need any additional settings.
• Wipe the fan body with a slightly damp cloth and then
wipe it dry.
ASSEMBLING THE FAN
• The fan is delivered with a disassembled base (1).
Do not switch the fan on without the base (1).
• Use a crosshead or at tip screwdriver (not supplied)
to assemble the base (1).
• Position the fan body (3) horizontally.
• Assemble the base (1): superpose the halves of the
base (1) (pic. 1) and x them with 2 fastening screws
(pic. 2).
• Attach the base (1) to the bottom part of the fan body
(3) with 4 fastening screws (pic. 3).
• Place the fan vertically on the base (1).
Remote control (23)
ATTENTION! A lithium battery is used in the remote
control. To avoid danger, do not allow children to
play with the battery. If your child has swallowed
a battery, immediately see a doctor. Battery
installation/replacing (pic. 4)
• Press on the clamp and remove the battery holder
(30) from the remote
• control (23) body, insert a CR2025 battery (supplied
with the unit) into the holder, strictly following the
polarity.
• Install the battery holder (30) into the remote control
(23).
Notes:
-if there is an isolation insert in the battery holder
(28), remove the insert;
-replace the battery in time;
-do not recharge the lithium battery;
-remove the battery if you are not planning to use
the unit for a long time;
-remove the used battery from the remote control
(23) and dispose of it.
9
EN
• When you use the remote control, direct it to the front
part of the fan body (3).
• The distance between the remote control and the fan
should not exceed 5 m, the coverage angle should
be up to 30 degrees.
• Avoid exposing the receiver to direct sunlight,
otherwise false activation of control commands is
possible.
USING THE FAN
• Use the handle (10) to carry the fan.
• Place the fan base (1) on a at, dry and steady
surface.
• Do not place the fanon soft surfaces, such as carpets
with high pile, sofas or beds.
• Insert the power cord plug into the mains socket, you
will hear a sound signal.
Switching the fan on/o and selecting the airow
speed
Notes:
-the buttons on the control panel (6) are sensory,
you just need to touch the button to switch the
necessary operation mode on;
-each pressing of buttons on the control panel (6)
or on the remote control (23) is accompanied with
a sound signal;
-if no buttons are pressed, then the display (5)
illumination will go out after 1 minutes. Digital
indications will go out after 3 minutes. To switch the
display on, press any button on the control panel (6)
or on the remote control (23).
• To switch the fan on, press the button (11) «ON/OFF»
on the control panel (5) or the button (24) «ON/OFF»
on the remote control (23), you will hear a sound
signal, and the fan will switch on at low airow speed,
the symbol (17) « » will light up on the display (5).
• The digital symbols (18) on the display (5) will show
the air temperature in the room.
Note: the temperature digital indications (18) may
be slightly dierent from the readings of another
thermometer.
• Pressing the button (16) «SPEED» on the control
panel (6) or the button (23) «SPEED» on the remote
control (23) you can select the airow speed, the
symbols (17) « ,,» will appear on the display.
• To switch the fan o, press the button (11) «ON/OFF»
on the control panel or the button (24) «ON/OFF» on
the remote control (23). The fan will be switched o
and the display (5) will go out.
Fan operation time timer
• To set the operating time of the fan, press the button
(15) «TIMER» on the control panel (6) or the button
(26) «TIMER» on the remote control (23), you will hear
a sound signal, the ashing digits (18) on the display
(5) will how the timer operation time «0 0» and the
symbol (21) « ».
10
EN
• Press again the buttons (15 or 26) to set the timer
operation time. Timer operation time can be set from
1 hour to 15 hours with 1 hour setting step.
• To switch the timer o, press the button (15 or 26)
repeatedly until the digital symbols (18) on the
display (5) show the room temperature.
Switching the fan body oscillation on/o
• To switch the fan body oscillation on, press the button
(14) «OSC» on the control panel (5) or the button
(29) «Oscillatior» on the remote control (23) to switch
the oscillation o, press again the button (14) «OSC»
on the control panel (5) or button (29) «Oscillatior»
on the remote control (23).
Selecting the airow type
• Press the button (12) «WIND» on the control panel
(6) or the button (28) «WIND» on the remote control
(23), while the display (5) will show the symbol (19)
«» - «natural wind», press the button (12 or 28)
again to switch the night mode on, the display (5) will
show the symbol (20) « », to switch the night mode
o, press the button (12 or 28) again, the symbol (20)
«» on the display (5) goes out.
Notes:
- «natural wind» is a natural wind imitating airow,
the airow speed is chaotically changing: from soft
breeze to strong gust of wind.
- «night mode» - the airow speed will increase and
decrease gradually;
• To switch the fan o, press the button (11) «ON/OFF»
on the control panel or the button (24) «ON/OFF» on
the remote control (23). The fan will be switched o
and the display (5) will go out.
Cool shot function
ATTENTION!During the hot season it is recommended
to regularly replace the water in the tank to avoid water
spoiling.
• Place the fan base (1) on a at, dry and steady
surface.
• •Make sure that the power plug is not inserted into
the mains socket.
• Remove the water tank lid (7).
• Fill the tank with clean water, do not exceed the
maximum water level mark «MAX» on the scale (2),
it is recommended to use water additionally cleaned
with a domestic lter.
Note: maximal capacity of the water tank is 5 l.
• Install the lid (7) back to its place.
Using the cool pack
ATTENTION! Do not leave children unattended to
prevent using the cool pack as a toy.
• For additional cooling of water, it is recommended to
use a cold pack (supplied with the unit).
Indice
Lingue:
Altri manuali BRAYER Fan
BRAYER
BRAYER BR4952 Manuale utente
BRAYER
BRAYER BR4953 Manuale utente
BRAYER
BRAYER BR4961BK Manuale utente
BRAYER
BRAYER BR4961WH Manuale utente
BRAYER
BRAYER BR4950 Manuale utente
BRAYER
BRAYER BR4956 Manuale utente
BRAYER
BRAYER BR4954 Manuale utente
BRAYER
BRAYER BR4955 Manuale utente
BRAYER
BRAYER BR4960 Manuale utente
BRAYER
BRAYER BR4974 Manuale utente
