Breville Easy Glide Manuale utente

Easy Glide 1800w steam iron

www.breville.co.uk

features

Water tank inlet cover

Steam control

Shot of steam button

Spray button

Temperature selector

Indicator light

Flexible cord protector

Due to our policy of continuous improvement, the actual product may differ slightly from the one illustrated in these instructions.

Heel rest

Cord wrap

Stainless steel soleplate

Pointer

Water level maximum indicator

Water tank

Spray nozzle

10.

11.

12.

13.

14.

q w e r

asd

t y

before rst use

Remove all packaging including any soleplate protection before heating the

iron.

Wipe over the soleplate with a cloth moistened with methylated spirit. Remove the

methylated spirit with a damp cloth then dry the soleplate thoroughly.

Fill the water tank and then empty it. This will rinse out any foreign particles remaining in

the water tank from the manufacturing process. Never ll your iron directly under a tap.

Always use the measuring cup supplied.

Before connecting your iron to the mains supply, make sure your supply voltage is the

same as the one indicated on your iron.

When you rst use your iron, there may be a slight odour and it may smoke slightly for the

rst few minutes of operation. This is quite normal and will disappear.

lling your iron

Never use fabric conditioner, starches or any other chemicals or additives.

Ensure the iron is switched off and unplugged from the mains supply socket.

Set the steam control to the no steam position (0).

Place the iron horizontally on a at, stable, dry, heat resistant and level surface and

open the water tank inlet cover.

Using the supplied measuring cup, ll the water tank with ordinary tap water. To avoid

air locks, tilt the iron slightly while lling it.

Don’t ll the iron above the water level indicator MAX marking. Check the water level

by standing the iron on its heel.

When the iron is lled close the water tank inlet cover.

TIP: We recommend that you:

Start with the fabrics to be ironed on a low temperature such as synthetic material.

Finish ironing with those fabrics which respond best to higher temperatures such as

linen.

If you iron a fabric made of a blend of bres; set the temperature control dial for the

most delicate bre.

Never use the burst of steam button on silks or synthetics.

When using starch, it should be sprayed onto the reverse side of the fabric and the

soleplate cleaned more frequently.

Do not iron over sharp or hard objects such as buttons, studs and zippers, as these

will scratch the surface of the soleplate.

•

using your iron

Ironing without steam

You may see this ‘Do not steam’ symbol on certain delicate fabrics. If you

intend to dry iron fabrics, there is no need to ll the water tank. However, if water is

already in the water tank, you do not need to empty it.

Set the steam control to the no steam position (0).

Plug your iron into the mains supply and switch on.

Set the temperature selector to the required temperature.

The indicator light will illuminate while the iron is heating up.

When the light goes out, your iron is ready to use. The indicator light will continue to

turn on and off during ironing as the iron maintains the soleplate temperature.

Steam ironing

During steam ironing, if you do not allow the iron to reach the selected

temperature water may drip from the soleplate.

It is recommended that for harder to iron fabrics such as cotton and linen, steam should

be used when ironing.

When ironing cotton and linen always select the highest temperature. Steam should

never be used on delicate fabrics like nylons, acrylics and synthetics.

Following the steps on page 4 ll the iron with water.

Plug your iron into the mains supply and switch on.

Turn the temperature selector until the pointer is within the steam setting range.

The indicator light will illuminate. When the indicator light goes out the iron is ready

to use. The indicator light will continue to turn on and off during ironing as the iron

maintains the soleplate temperature.

Adjust the steam control for the desired steam output.

Adjust the steam control lever to the right to increase the amount of steam , or to

the left to decrease the amount of steam .

The iron will automatically begin to steam as soon as the iron is used.

The steam can be shut off at any time by setting the steam control to the no steam

position (0).

Pointer

Temperature selector

using your iron

Burst of Steam

Note: The temperature selector must be set within the steam setting range (see page

5) when using the shot of steam function. Wait for several seconds between each

press of the steam button.

Press the shot of steam button whenever you have a stubborn crease that needs

extra steam. Steam will burst from the holes in the soleplate into the fabric.

Vertical Steam Ironing

Never iron garments when they are being worn.

Your iron can be used for vertical steam ironing. This process can be applied to

curtains, dresses on hangers etc.

Following the steps on page 4 ll the iron with water.

Plug your iron into the mains supply and switch on.

Turn the temperature selector until the pointer is within the steam setting range. The

hotter the iron, the more steam is generated.

The temperature indicator light will illuminate to show that the iron is heating.

When the indicator light goes out, the iron is ready to use. The indicator light will

cycle on and off during ironing as the iron maintains the soleplate temperature.

Hold the iron 15cm (6 inches) from the fabric.

Press the shot of steam button. The steam will penetrate the fabric removing the

creases. To apply more steam press the shot of steam button again.

Spraying

Note: The spray function will only operate when there is water in the water tank.

The water spray can be used to help iron heavy fabrics or difcult areas (collars,

pockets, sleeves, creases, etc). It can also be used when ironing delicate fabrics

which cannot be steam ironed.

Simply press the spray button as required to emit a spray of water. If the spray is

being used for the rst time, or if the iron has been standing for some time, you

may need to press the spray button a few times to prime the spray before it works

correctly.

using your iron

Note: When the temperature selector is changed from a high setting to a lower

setting during ironing, the indicator light will go out immediately. This indicates that

the iron is cooling to the selected temperature. To ensure that the iron has reached

the selected temperature and is not too hot, wait until the indicator light comes on

again, and then goes out before ironing.

Anti-Drip Function

The supply of water is cut off automatically to avoid any drips from the soleplate

when the temperature of the iron is insufcient to produce steam.

•

Do not use harsh abrasives, chemical cleaners or solvents to clean the exterior

of your iron because they will damage the surface.

Cleaning the Soleplate on your Iron

After each use, allow iron to cool fully before wiping the soleplate with a damp soft cloth.

If polyester has burnt to the soleplate, iron a damp cotton cloth while hot. If necessary,

allow unit to cool fully and wipe over the soleplate with a soft cloth and a small amount of

methylated spirits. Remove the methylated spirit with a damp cloth. Ensure soleplate is

dried thoroughly.

Cleaning the Steam Holes

To remove build-up from the steam holes which may affect steam performance, use a

cotton wool tip moistened in methylated spirits. Wipe over with a damp cloth.

To clean the exterior of your iron, wipe over with a damp soft cloth and wipe dry. Ensure

the soleplate is then dried thoroughly.

Putting your Iron Away

Set the steam control to the no steam position (0).

Turn the power off and remove the plug from the power outlet.

When the soleplate has cooled, empty remaining water from the tank.

Storage

Always store the iron on its heel rest, allowing to cool for 30 minutes.

Do not store the iron with the soleplate facing down, or in the carton.

Do not wrap the cord around the soleplate. The cord can be neatly wrapped around

the heel of the iron.

care and cleaning

product safety

Please read these instructions before operating the appliance and retain them for

future use.

This product is not suitable for use by children, and may not be suitable for persons

requiring supervision unless they receive instruction by a competent person on how to

safely use the product. Children should be supervised to ensure that they do not play

with the product.

Never use this appliance for anything other than its intended use. This appliance is for

household use only. Do not use this appliance outdoors.

Always ensure that hands are dry before handling the plug or switching on the

appliance.

Never leave the appliance unattended when it is connected to the mains supply.

Ensure the appliance is switched off and unplugged from the supply socket before

lling or emptying the water tank, after use and before cleaning.

Do not use the appliance if it has been dropped, if there are any visible signs of

damage or if it is leaking.

Always use the appliance on a stable, secure, dry and level surface. When placing the

appliance on its stand, ensure that the surface on which the stand is placed is stable.

Do not touch the metal parts of the appliance during use as they may become very hot.

Never operate the appliance by means of an external timer or separate remote-control

system.

This appliance must not be placed on or near any potentially hot surfaces (such as a

gas or electric hob).

The power cord is not replaceable by the user. Always return the appliance if the power

cord is damaged to avoid any hazard.

Always allow the appliance to cool before cleaning or storing.

Never immerse any part of the appliance or power cord and plug in water or any other

liquid.

Never let the power cord hang over the edge of a worktop, touch hot surfaces or

become knotted, trapped or pinched.

This appliance must be earthed.

This appliance is tted with either a moulded or rewirable BS1363, 13 amp plug. The fuse

should be rated at 13 amps and be ASTA approved to BS1362.

If the fuse in a moulded plug needs to be changed, the fuse cover must be retted. The

appliance must not be used without the fuse cover tted.

If the plug is unsuitable, it should be dismantled and removed from the supply cord

and an appropriate plug tted as detailed below. If you remove the plug it must not be

connected to a 13 amp socket and the plug must be disposed of immediately.

The wires of the mains lead are coloured in accordance with the following code:

GREEN/YELLOW = EARTH BLUE = NEUTRAL BROWN = LIVE

The wire which is coloured GREEN/YELLOW must be connected to the terminal in

your plug which is marked with an E or by the earth symbol ( ) or coloured GREEN or

GREEN /YELLOW.

The wire which is coloured BLUE must be connected to the terminal in your plug which is

marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in your plug which

is marked with the letter L or coloured RED.

If any other plug is used, a 13 amp fuse must be tted either in the plug or adaptor or at

the distributor board.

Plug should be BS1363 approved

Fit a 13 Amp Fuse

Ensure that the outer sheath of the cable

is rmly held by the clamp

BROWN

(Live)

13 Amp

Fuse

BLUE

(Neutral)

GREEN/YELLOW

(Earth)

connection to the mains supply

Indice

Altri manuali Breville Ferro

Breville

Breville VIN439 Manuale utente

Breville

Breville VIN169 Guida alla risoluzione dei problemi

Breville

Breville Easy glide 2200W Manuale utente

Breville

Breville VIN225 Manuale utente

Breville

Breville Easy Glide VIN243 Manuale utente

Breville

Breville vin276 Manuale utente

Breville

Breville VIN253X Manuale utente

Breville

Breville VIN359 Manuale utente

Breville

Breville PressXpress soleTEMP VIN411X Manuale utente

Breville

Breville TECHnique digital VIN158 Manuale utente

Breville

Breville VIN267 Manuale utente

Breville

Breville Power Steam VIN299 Manuale utente

Breville

Breville Power Steam VIN177 Manuale utente

Breville

Breville VIN208 Manuale utente

Breville

Breville Power Steam VIN268 Manuale utente

Breville

Breville VIN170 Manuale utente

Breville

Breville VIN281 Manuale utente

Breville

Breville VIN325X Manuale utente

Breville

Breville Technique Manuale utente

Breville

Breville VIN359 Manuale utente

Breville

Breville PressXpress VIN338 Manuale utente

Breville

Breville VIN250X Manuale utente

Breville

Breville BIR300 Manuale utente

Breville

Breville PressXpress VIN410X Manuale utente

Manuali Ferro popolari di altre marche

Clatronic

Clatronic DB 3703 Manuale utente

TEFAL

TEFAL FV4093Z0 Manuale utente

Gorenje

Gorenje SIH 2200 BS Manuale utente

Philips

Philips GC6012 Manuale utente

Bosch

Bosch 2 Series Manuale utente

Riffel

Riffel Catena KB-819 Manuale utente

Texi

Texi Hestia Manuale utente

Maxwell

Maxwell MW-3010 Manuale utente

TREVIDEA

TREVIDEA Girmi ST60 Manuale utente

Philips

Philips HI5914/30 Manuale utente

Primula

Primula Vapormat Manuale utente

Magio

Magio MG-541 Manuale utente

Scarlett

Scarlett SC-1334S Manuale utente

Bosch

Bosch Sensixx B22L Manuale utente

Philips

Philips GC651 Manuale utente

Vitek

Vitek VT-1247 VT Manuale utente

Cleanmaxx

Cleanmaxx 3397 Manuale utente

Philips

Philips GC800 Manuale utente