Brickcom PZ-040 12x Series Manuale utente
12x PTZ Network Camera
PZ-040 12x Series
Quick Installation Guide
Read Before You Use
1. Power off the camera device immediately if it starts
smoking or smells unusual.
2. Power off the camera device
immediately if the camera is exposed to rain
or liquid.
3. Do not set the camera device near any
heat sources. (Ex: television and oven)
4. Keep the camera device away from
direct sunlight.
5. Do not set the camera device over the specific operating
temperature.
6. Do not set the camera device in any wet
and humid environments.
7. Do not set the camera device on
unsteady surfaces.
8. Do not attempt to dismantle the camera
device.
9. Do not drop or hit the camera device.
10. Do not use the camera device when
there is lightning.
1. Check Package Contents
a. PZ-040D/E 12x
b. Product CD
c. Mounting Kit
d. I/O Cable
e. Warranty Card
f. Screw Bag
g. Easy Installation Guide
i. Alignment Sticker
2. Device Description
<Front View>
<I/O Connectors>
Video Out
Microphone/Line In (Green)
Light Sensor
12 IR LEDs
Audio Out (Red)
General I/O Terminal Block
DC Power Connector
Ethernet RJ45 10/100 Socket
I/O Cable
3. Hardware Installation
1.Connect the supplied I/O cable to the camera.
2.Install the Mounting Kit
Step1.Choose a location on the wall or ceiling to place the camera.
Attach the location sticker to the desired spot. Drill holes through
the three location holes and cable hole on the sticker.
Step2.For Hard Ceiling Mount, hammer the three plastic anchors that are
provided into the three location holes.
For Soft Ceiling Mount, place the hollow plate on the back side of
the ceiling and align the three holes on the plate with the screw
location holes.
Step3.Mount the metal plate on the ceiling and position the three screw
slots over the plastic anchors. Insert the three screws provided in
the product package into the holes and use a screwdriver to
tighten the screws clockwise until they are secure.
Hard Ceiling Mount
Soft Ceiling Mount
3.Loosen the screw on the rim of the metal plate but do not remove the
screw completely.
4.Push all cables and connectors through the cable hole into the ceiling, and
attach the PTZ camera to the metal plate.
5.Turn the PTZ camera counter clockwise until it is in a locked position
6.Tighten the screws on the metal plate.
4. Camera Connection
1. Basic Connection (Without PoE)
1.1 Connect the camera to a switch using a standard Ethernet cable.
1.2 Connect the power adapter from the camera to a power outlet.
Note: A DC12V 2A power adapter is required.
2. Power over Ethernet (PoE) Connection
2.1 The PZ-040D/E is High Power PoE compliant, so there are two
options for connecting the camera to a power and Ethernet
source. The camera can either be connected to a High
PoE-enabled switch or a non-PoE switch
A. If using a High Power PoE-enabled switch
Use a single Ethernet cable to connect the camera to the High Power
PoE-enabled switch.
Note: The PoE switch must be able to provide IEEE802.3at High
Power PoE.It is recommended that a Brickcom PS-7242-AT 24
port high power PoE switch be used.
B. If using a non-PoE switch
1. Use a standard Ethernet cable to connect the camera to a High Power
PoE Injector.
2. Use a standard Ethernet cable to connect the High Power PoE Injector
to the non-PoE switch.
3. Use a standard power cable to connect the High Power PoE Injector to
a power outlet.
Note: The PoE injector must be able to provide IEEE802.3at High
Power PoE. It is recommended that a Brickcom POE30U high
power PoE injector be used.
7. Setup the Network Camera
1. Insert the Installation CD into the CD-ROM driver. Run Auto-Run Tool
directly from the CD-ROM to start the installation. When installing the
Brickcom software kit for the first time, select a desired language for the
interface. The available languages are listed in the scroll box. Click
“Install” and follow the steps to install the EasyConfig wizard on the
desired computer.
Please follow the InstallShield Wizard instructions to finish the Brickcom
Software Kit installation.
Altri manuali per PZ-040 12x Series
1
Indice
Altri manuali Brickcom Telecamera di sicurezza
Brickcom
Brickcom VD-E400Af Istruzioni per l’uso
Brickcom
Brickcom CB-101A Series Manuale utente
Brickcom
Brickcom CB-500A Series Manuale utente
Brickcom
Brickcom FB-130Np Series Manuale utente
Brickcom
Brickcom CB-100Ap-0c Scheda tecnica
Brickcom
Brickcom MD-100Ae Manuale utente
Brickcom
Brickcom MD-500Ap Series Manuale utente
Brickcom
Brickcom VD-130Af Manuale utente
Brickcom
Brickcom CB-100A Series Manuale utente
Brickcom
Brickcom MD-100A series Manuale utente
Brickcom
Brickcom OSD-040 36x Series Manuale utente
Brickcom
Brickcom OB-100A V2 series Istruzioni per l’uso
Brickcom
Brickcom Vandal Dome Series Scheda tecnica
Brickcom
Brickcom FB-Series Scheda tecnica
Brickcom
Brickcom VD-100A Manuale utente
Brickcom
Brickcom CB-100A Series Manuale utente
Brickcom
Brickcom VD-130A V2 Series Manuale utente
Brickcom
Brickcom FB-100A Series Manuale utente
Brickcom
Brickcom Vandal Dome V2 Series Manuale utente
Brickcom
Brickcom FB-H200Np-S-WDRPro Scheda tecnica
