Burkert 2060 Guida
Austauschanleitung
Instructions de remplacement
Replacement Instructions
Type 2060
2/2-way angle seat valve
2/2-Wege-Schrägsitzventil
Vanne à siège incliné 2/2 voies
Address / Adresse
Germany / Deutschland / Allemagne
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: [email protected]
International
www.burkert.com
Manuals and data sheets on the Internet:
www.burkert.com
Bedienungsanleitungen und Datenblätter im Internet:
www.buerkert.de
Instructions de service et fiches techniques sur Internet:
www.burkert.fr
© Bürkert Werke GmbH & Co. KG, 2019
Replacement Instructions 1907/00_EU-ml_00815316 /
Original DE
2
1 SYMBOLS
▶Highlights instructions to avoid a danger.
→Designates a procedure which you must carry out.
DANGER!
There is an imminent danger of serious or fatal injuries.
WARNING!
There is a potential danger of serious or fatal injuries.
CAUTION!
There is a danger of minor or moderate injuries.
2 REPLACEMENT PART SET
The following replacement part sets are available for the angle seat
valve Type 2060:
•Swivel plate set
consisting of swivel plate, pin and seal
•Seal set for packing gland
(only actuator sizes 70, 90 and 130)
consisting of the individual parts of the packing gland, seal and
lubricant
(the modied socket wrench is not included in the seal set)
3 OVERVIEW OF REPLACEMENT PART SETS
Pos. Description
1
Swivel plate
set
Seal (packaged)
2Swivel plate
3Pin
4Seal set for packing gland
(only actuator sizes 70, 90 and 130)
1
2
3
4
english
3
NOTE!
Damage to the valve seat seal or seat contour.
When removing the actuator, the valve must be in the open
position.
▶For control functions A (SFA) and I (SFI) pressurise the pilot air
port 1with compressed air (5 bar): Valve opens.
→Place a suitable open-end wrench on the wrench at of the nipple
and unscrew the actuator from the valve body.
Actuator
Nipple
Valve body
Wrench at
for open-end
wrench
Exhaust port SFB
Pilot air port
SFA, SFI
Exhaust port
SFA
Pilot air port
SFB, SFI
2
1
4 CHANGE SWIVEL PLATE SET
DANGER!
Risk of injury from discharge of pressure and escaping medium.
Working on a device, which is under pressure, is hazardous due to
a sudden discharge of pressure or escaping medium.
▶Before working on the device or system, switch o the pressure.
Vent or empty the lines.
WARNING!
Risk of injury due to using wrong tool.
Performing installation work, using unsuitable tools, is hazardous
due to possible damage to the device.
▶To remove the actuator from the valve body, use an open-end
wrench, never a pipe wrench.
Before replacing the replacement parts, remove the actuator
from the valve body.
4.1 Removing actuator from the valve body
→Clamp valve body in a holding device (only for valves which
have not yet been installed).
english
4
4.2 Replace swivel plate set
→Support swivel plate on the cylindrical part using a prism or
something similar.
→Knock out pin using a suitable pin punch
(see “Tab. 1”).
→Remove swivel plate.
→Connect new swivel plate to the spindle.
→Align boreholes in the swivel plate and spindle.
Spindle
Pin
Swivel plate
Seal
→Support swivel plate on the cylindrical part using a prism or
something similar.
→Insert pin into the borehole.
→Caulk pin boreholes on both sides of the swivel plate using a
chisel or centre punch.
Spindle
[ø in mm]
Orice DN Actuator size
[ø in mm]
Suitable pin
punch
[ø in mm]
815...25 50 3
10 15...50 70
14 32...65 90 5
130
Tab. 1: Suitable pin punch in relation to the spindle diameter
english
5
4.3 Installing actuator on valve body
WARNING!
Danger from using wrong lubricant.
Unsuitable lubricant may contaminate the medium. There is a risk
of explosion in oxygen applications!
▶For specic applications, e.g. oxygen or analysis applications,
use approved lubricants only.
→Check seal and replace if required.
→Before re-installation, grease nipple thread of the actuator (e.g.
using Klüberpaste UH1 96-402 from Klüber).
NOTE!
Damage to the valve seat seal or seat contour.
When removing the actuator, the valve must be in the open
position.
▶For control functions A (SFA) and I (SFI) pressurise the pilot air
port 1with compressed air (5 bar): Valve opens.
→Screw actuator onto valve body. Observe tightening torque (see
“Tab. 2”).
1
2
Exhaust port SFB
pilot air port SFA, SFI
Exhaust port SFA
Pilot air port SFB, SFI
Tightening torques valve body / nipple
Orice DN Tightening torques
[Nm]
15 45 ± 3
20 50 ± 3
25 60 ± 3
32
65 ± 3
40
50 70 ± 3
65 100 ±3
Tab. 2: Tightening torques valve body / nipple
english
6
5 REPLACING PACKING GLAND
DANGER!
Risk of injury from discharge of pressure and escaping medium.
Working on a device, which is under pressure, is hazardous due to
a sudden discharge of pressure or escaping medium.
▶Before working on the device or system, switch o the pressure.
Vent or empty the lines.
WARNING!
Risk of injury due to using wrong tool.
Performing installation work, using unsuitable tools, is hazardous
due to possible damage to the device.
▶To remove the actuator from the valve body, use an open-end
wrench, never a pipe wrench.
The seal set for the packing gland includes:
•1 support ring •1 spindle guide
•7 chevron seals •1 seal
•2 thrust collars •Lubricant
•1 compression spring
Before replacing the replacement parts, remove the actuator
from the valve body and remove the swivel plate.
5.1 Removing actuator from the valve body
→Clamp valve body in a holding device (only for valves which
have not yet been installed).
NOTE!
Damage to the valve seat seal or seat contour.
When removing the actuator, the valve must be in the open
position.
▶For control functions A (SFA) and I (SFI) pressurise the pilot air
port 1with compressed air (5 bar): Valve opens.
→Place a suitable open-end wrench on the wrench at of the nipple
and unscrew the actuator from the valve body.
Actuator
Nipple
Valve body
Wrench at for open-end wrench
Exhaust port SFB
Pilot air port SFA, SFI
Exhaust port SFA
Pilot air port SFB, SFI
2
1
english
7
5.2 Removing swivel plate
→Support swivel plate on the cylindrical part using a prism or
something similar.
→Knock out pin using a suitable pin punch
(see “Tab. 3”).
→Remove swivel plate.
Spindle
[ø in mm]
Orice DN Actuator size
[ø in mm]
Suitable pin
punch
[ø in mm]
10 15...50 70 3
14 32...65 90 5
130
Tab. 3: Suitable pin punch in relation to the spindle diameter
Spindle
Pin
Swivel plate
Seal
5.3 Replacing packing gland
→Unscrew spindle guide using a modied socket wrench2).
2)
The modied socket wrench is available from your
Bürkert sales department (see Page 10).
Packing gland
Spindle guide
Spindle
Packing gland tube
WARNING!
Risk of injury due to parts being ejected.
When the spindle opening is exposed, the individual parts of the
packing gland will be pressed out at an undened speed when
the pilot air port is pressurised.
▶Before pressurising with pilot air, safeguard the area around
the outlet, (e.g. place spindle on a rm surface).
english
8
→Using compressed air, press packing gland out of the packing
gland tube.
For control function A and I:
Pressurise pilot air port 1 with compressed air (6...8 bar)
For control function B:
Pressurise pilot air port 2 with compressed air (6...8bar)
→Grease the individual parts of the new packing gland with the
supplied lubricant.
→Place individual parts on the spindle in the specied direction
and sequence.
→Push the packing gland into the packing gland tube.
→Screw in the spindle guide using the socket wrench. Observe
tightening torque (see “Tab. 4”)!
Spindle [ø in mm] Tightening torque [Nm]
10 6
14 15
Tab. 4: Tightening torques spindle guide
Support ring
Upper chevron seals
Upper thrust collar
Compression spring
Lower thrust collar
Lower chevron seals
Spindle guide
Insertion direction
for packing gland parts
english
9
5.4 Installing swivel plate
→Connect swivel plate to the spindle.
→Align boreholes in the swivel plate and spindle.
Spindle
Pin
Swivel plate
Seal
→Support swivel plate on the cylindrical part using a prism or
something similar.
→Insert pin into the borehole.
→Caulk pin boreholes on both sides of the swivel plate using a
chisel or centre punch.
5.5 Installing actuator on valve body
WARNING!
Danger from using wrong lubricant.
Unsuitable lubricant may contaminate the medium. There is a risk
of explosion in oxygen applications!
▶For specic applications, e.g. oxygen or analysis applications,
use approved lubricants only.
→Check seal and replace if required.
→Before re-installation, grease nipple thread of the actuator (e.g.
using Klüberpaste UH1 96-402 from Klüber).
NOTE!
Damage to the valve seat seal or seat contour.
When removing the actuator, the valve must be in the open
position.
▶For control functions A (SFA) and I (SFI) pressurise the pilot air
port 1with compressed air (5 bar): Valve opens.
→Screw actuator onto valve body. Observe tightening torque (see
“Tab. 5”).
english
10
1
2
Exhaust port SFB
pilot air port SFA, SFI
Exhaust port SFA
Pilot air port SFB, SFI
Orice DN Tightening torques
[Nm]
15 45 ± 3
20 50 ± 3
25 60 ± 3
32
65 ± 3
40
50 70 ± 3
65 100 ±3
Tab. 5: Tightening torques valve body / nipple
6 INSTALLATION TOOLS
SW
Modied socket wrench for packing gland
Socket wrench Orice DN AF Order No.
Spindle
ø10 mm 15...50 19 683221
Spindle
ø14 mm 32...65 21 683223
Tab. 6: Modied socket wrench
Special wrench for turning the actuator
Order number 665702
Tab. 7: Special wrench
If you have any questions, please contact your Bürkert
sales department.
english
Altri manuali per 2060
7
Indice
Altri manuali Burkert Unità di controllo
Burkert
Burkert 2103 Series Manuale utente
Burkert
Burkert 2065 Manuale utente
Burkert
Burkert AirLINE 8652 Series Manuale utente
Burkert
Burkert 0250 Manuale utente
Burkert
Burkert 2610 Manuale utente
Burkert
Burkert 2101 Manuale utente
Burkert
Burkert 6211 Manuale di istruzioni
Burkert
Burkert 8681 Manuale utente
Burkert
Burkert 0301 Manuale utente
Burkert
Burkert 6724 Series Manuale utente
Burkert
Burkert 2030 Manuale utente
Burkert
Burkert 6038 Manuale utente
Burkert
Burkert 8690 Manuale utente
Burkert
Burkert 2651 Manuale utente
Burkert
Burkert 6240 Manuale utente
Burkert
Burkert 2030 Manuale utente
Burkert
Burkert 8653 AirLINE Field Manuale utente
Burkert
Burkert 6221 Manuale utente
Burkert
Burkert 5420 Manuale utente
Burkert
Burkert 3270 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
