CAS NC-100 Manuale utente
NC Series
Crane Scale
OWNER’S MANUAL
CONTENTS
PRECAUTIONS 4
PREFACE 6
NAMES AND FUNCTIONS 6
1. OVERALL VIEW 6
2. DISPLAY 6
3. KEY FUNCTIONS 7
OPERATIONS 7
1. POWER ON 7
2. ZERO OPERATION 7
3. TARE OPERATION 8
4. UNIT CONVERSIONS 9
ERROR MESSAGES 9
1. ERROR 1 9
2. ERROR 3 9
3. OVER LOAD 10
4. ERROR BEEP 10
THE PROGRAMS 10
1. TO SELECT MOTION BAND 10
2. TO SELECT DIGITAL FILTER 11
3. TO SELECT AUTO-POWER OFF INTERVAL 11
4. TO SET E.L. ON OR OFF 12
BATTERY OPERATION 13
1. CHARGE 13
2. BATTERY OPERATING TIME 14
3. LOW BATTERY("BAT.") SIGNAL 14
REMOTE CONTROL 14
1. REMOTE CONTROLLER OPERATION 14
2. REPLACING BATTERY IN REMOTE CONTROLLER 14
ASSEMBLE AND DISASSEMBLY 15
SPECIFICATIONS 16
45
PRECAUTIONS
Do not disassemble the scale.
When any damage or
defect occurs, contact
your CAS authorized
dealer immediately for
proper repair.
Do not overload beyond the maximum
weight limit.
Do not pull the plug by its cord when
unplugging. Damaged cord could cause
electric shock or fire.
Avoid placing the scale near heater
or in direct sunlight.
Scale must be grounded to minimize
electricity static. This will minimize
defect or electric shock.
Use proper Adapter. Incorrect adapter
could damage the scale. Insert plug firmly to wall outlet to
prevent electric shock.
To reduce electric shock or incorrect
reading, Do not spill water on the scale
or place it in humid condition.
Warning
To prevent from fire occurring, Do not
place or use the scale near
flammable or corrosive
gas.
For consistent and accurate reading,
maintain periodical check by your
CAS authorized dealer.
Avoid sudden shock to the scale.
Internal mechanism could be damaged.
Place the scale on firm and temperature
consistent environment.
Attention
Keep the scale away from other
electromagnetic generating devices.
This may interfere with accurate
reading.
Take the battery out when scale is not in
use for long time. Leakage from the
batteries is hazardous.
7
6
PREFACE
NAMES AND FUNCTIONS
Thank you for purchasing our CAS NC SERIES.
These series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your specialty departments can enjoy these
high quality reliable CAS products.
We believe that your needs will be satisfied and you will have proper reliability.
This manual will help you with proper operation and care of the CASTON .
Please keep it handy for future reference.
1. OVERALL VIEW
KEY BOARD
HOOK
JOINT RING ASSY
DISPLAY WINDOW
NAME
PLATE
FRONT VIEW REAR VIEW
SEALING
BOLT
ON/OFF
S/W
ON
OFF
JACK
RUBBER
2. DISPLAY
ZERO LAMP : It shows zero state. When the scale is loaded,
the lamp will be turned off.
TARE LAMP : It is lit when the tare weight entered.
BAT. LAMP : It is lit when battery needs to be exchanged.
EXTERNAL POWER OPERATION LAMP : It is lit when DC 12V
adaptor supplies power to scale.
RECHARGE END LAMP : It is lit when being recharged and turn off
when recharge finishes.
3. KEY FUNCTIONS
ZERO
TARE
Turns power on or off.
Zero the scale when the zero point is drifted.
Subtracts tare weight gross weight.
Select kg or lb.(Capture and display weight)
KEYS FUNCTIONS
OPERATIONS
1. POWER ON
Press "ON/OFF" key.
2. ZERO OPERATION
Press "ZERO" key when the zero point is drifted.
SPEC PLATE
9
8
3. TARE OPERATION
Load tare on the hook.
Press "TARE" key.
"0" is displayed, and the tare is subtracted.
4. UNIT CONVERSIONS
Place an item to be weight on the hook.(GRAM MODE)
lb
Remove tare on the hook.
Press "TARE" key.
The tare weight is cleared appers in the display window.
Remove weight on the hook.
Press "kg/lb" key.(POUND MODE)
Place an item to be weight on the hook.
ERROR MESSAGES
1. ERROR 1 Over-range error of an initial zero.
Make the hook empty.
2. ERROR 3 The scale needs calibration.
11
10
3. OVER LOAD When a load is over the limit weight
of a scale.
LIMIT WEIGHT=CAPACITY+6D
4. ERROR BEEP
When pressing "ZERO" key while TARE is used.
When pressing "ZERO" or "TARE" key while a scale is not stable.
When pressing "ZERO" key while ZERO RANGE OVER happens.
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
1. TO SELECT MOTION BAND
THE PROGRAMS
Turn power on pressing "ZERO" key.
Press "kg/lb" (HOLD)key.
is displayed.
is displayed.
(See TABLE 1)
is displayed.
(See TABLE 2)
TABLE 1
(* D=INTERVAL)
MOTION BAND IS THE RANGE THAT MAKES A SCALE HANDLE
AN UNSTABLE WEIGHT AS A STABLE WEIGHT IN.
2. TO SELECT DIGITAL FILTER
DIGITAL FILTER IS THE FUNCTION THAT MAKES DISPLAY
SPEED FASTER OR SLOWER ON THE USING CONDITION.
THE HIGHER VALUE IS THE LOWER SPEED.
3. TO SELECT AUTO-POWER OFF INTERVAL
AUTO POWER OFF IS THE FUNCTION THAT MAKES POWER
DOWN WHEN A SCALE IS NOT OPERATED BY USER TO SAVE
BATTERY POWER.
01D
15D
2 10D
TABLE 2
0 NONE
1 FASTER
7 SLOWER
13
12
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
Press "kg/lb"(HOLD) key.
The scale returns to NORMAL MODE.
is displayed.
(See TABLE 3)
TABLE 3
0 NONE
1 3 min
2 6 min
3 9 min
(See TABLE 3)
TABLE 4
0
OFF always
1
ON weighing and stable
2
ON weighing
3
ON always
4. TO SET E.L. ON OR OFF
E.L BACK LIGHT IS THE FUNCTION THAT MAKES THE
DISPLAY PANEL VISIBLE IN THE DARK BY LIGHTING
ELECTRIC LUMINANCE DEVICE.
BATTERY OPERATION
1. CHARGE
The rechargeable battery located inside the NC-series scale must be
charged using the voltage which don't exceed 10% of the voltage
indicated on the adapter.
If the voltage for charge exceed the above limit, the battery would
be damaged.
Check if an output voltage is DC 12V 1.5A.
Remove ADAPTOR JACK COVER of REAR PANEL and connect
adaptor with an scale like the following figure.
When an adaptor is linked with an scale, RED LAMP and
GREEN LAMP are ON.
Charging method.
Quick charge : Charge the battery until the green lamp is ON.
(Quick charging time : approximately 2 hours)
Standard charging method : Charge the battery for about 6 hours
after the green lamp is ON.
Note : If you use the quick charge, the battery is not charged fully.
(charged to the 70% of full charge)
To charge fully, use the standard charge.
15
14
2. BATTERY OPERATING TIME
The discharge time is dependent on the charging method and
power source.
In generally, if you use the battery continuously, the discharge
time is as follows.
with E.L. 16~22hours.
without E.L. 37~50hours.
Caused by repeated use, the discharge time can be decreased.
If the scale is not used for long time after charging the battery,
the discharge time is decreased. To restore the discharge time,
repeat the procedure of charge and discharge(if battery is
discharged the "BAT" lamp on the LCD will be displayed) for
2 or 3 times.
3. LOW BATTERY("BAT.") SIGNAL
To protect over-discharge of BATTERY, "BAT" LAMP is lit when
battery has to be charged.
A scale turns power off automatically an fixed period after "BAT"
is ON.
1. REMOTE CONTROLLER OPERATION
"ON/OFF" key : Power ON/OFF.
"ZERO" key : Make the scale stable to "0" while the zero point is drifted.
"TARE" key : Store the tare weight.
"kg/lb" key : Select kg or lb mode.
"HOLD" key : Capture and display weight.
OPERATION LAMP : Blinks once when keys are pressed.
2. REPLACING BATTERY IN REMOTE CONTROLLER
BATTERY SPEC.
VOLTAGE : 1.5V 2
SIZE : AA SIZE(14.5 50.5m/m)
BATTERY
NOTE ON REPLACING BATTERIES.
Place batteries in correct polarity(+)(-)direction.
Do not use new batteries with the used.
REMOTE CONTROL
ASSEMBLE AND DISASSEMBLY
DEVICE PIN
HOOK
LOAD PIN
17
16
SPECIFICATIONS
MODEL
MAXIMUM CAPACITY
INTERVAL
FUNCTION
DISPLAY COLUMN
DISPLAY TYPE
DISPLAY DESIGNATORS
MAX TARE
WEIGHING TYPE
OPERATING TEMPERATURE
OPERATING POWER
POWER SOURCE
POWER CONSUMPTION
NET WEIGHT
NC-100 NC-200 NC-500 NC-1
100kg 200kg 500kg 100lb 250lb 1000lb
(200lb) (400lb) (1250lb) (40kg) (125kg) (400kg)
0.05kg 0.1kg 0.2kg 0.05lb 0.1lb 0.5lb
(0.02lb) (0.2lb) (0.5lb) (0.02kg) (0.05kg) (0.2kg)
ON/OFF, TARE, ZERO, kg/lb CONVERTING(HOLD)
5DIGIT
L.C.D TYPE
ZERO, TARE, BAT.
FULL TARE
LOAD CELL TYPE
-10
°C
~ +40
°C
DC 12V(1.5A)
AC 110/120 /220/240 V, 50/60Hz
0.25W
5.5kg
MEMO
18
MEMO
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali CAS Scala
CAS
CAS CL-3000 Series Manuale utente
CAS
CAS EC-II Series Manuale utente
CAS
CAS BFA-2 Manuale utente
CAS
CAS 25AC Manuale utente
CAS
CAS CT100 Series Manuale utente
CAS
CAS GBF-1039 Manuale utente
CAS
CAS PD-I Istruzioni utente
CAS
CAS SW-2 Manuale utente
CAS
CAS AP-US Series Manuale utente
CAS
CAS LP-II Istruzioni di installazione e manutenzione
CAS
CAS ERII-6 Manuale utente
CAS
CAS HE-52 Manuale utente
CAS
CAS BF-1410 Manuale utente
CAS
CAS CL7200 series Manuale utente
CAS
CAS RW-2601P Series Manuale utente
CAS
CAS LP-II Istruzioni di installazione e manutenzione
CAS
CAS EB Series Manuale utente
CAS
CAS GBF-1251 Manuale utente
CAS
CAS CASTON II Manuale utente
CAS
CAS CL8000 Series Manuale utente
