Cavalry CADA001C32A Manuale utente
User’s Guide: CADA-C32A Series RAID Enclosure
This guide contains instructions for changing the RAID settings on your CADA-C32A Series
Personal Disk Array. If you need assistance, please contact customer service at
[email protected]. The guide is structured as follows:
Product Diagrams - Page 2
RAID Settings Overview with Explanations - Page 3
Instructions for Changing RAID Settings - Page 4
1
Diagrams
Front View:
1. Power indicator
2. Rebuild indicator
3. HDD1 Access Indicator
4. HDD2 Access Indicator
5. HDD1 Error Indicator*
6. HDD2 Error Indicator*
7. Ventilation
*The error LEDs light up when the
corresponding hard drive fails, when
there are rebuilding errors and when the
corresponding hard drive is not present.
Rear View:
1. Power switch
2. Power port
3. FIREWIRE 1394 A port
4. FIREWIRE 1394 B ports
5. USB 2.0 port
6. Fan for ventilation
2
RAID Settings Descriptions
SINGLE MODE Array will show up as two independent drives. This function
can be used if only if two different brands and/or capacities
of HDDs (Hard Disk Drives) are installed.
SPANNING MODE Two HDDs will show up as a single drive with the combined
capacity of both drives. Spanning writes data sequentially
across two drives.
RAID 0 (Striping) Two HDDs will show up as a single drive with the combined
capacity of both drives. Speed and performance increase.
The two HDDs “stripe" data across the two drives. This splits
each piece of Data across both HDDs in segments in a way
that speeds up reading and writing times. However, RAID 0
does not offer any data protection: if one drive fails or is
damaged, all data can be lost.
RAID 1 (Mirroring) The RAID controller creates an extra copy (or mirror) of data
on the two drives. Only a single drive will show up on your
computer, and it will have the capacity of a single drive.
Data is protected from the failure of one drive. If one drive
fails, replace it with an identical drive and the data rebuilds
automatically.
Using this mode requires 2 identical HDDs; the two drives
must be the same capacity, brand and model number.
3
Changing RAID Settings
1. Start your computer and wait for your operating system to load completely.
2. Connect the appropriate end of the USB / FireWire cable to your CADA-C32 disk
array. Connect the other end of the USB / FireWire cable to your computer.
3. Connect the power cable to your CADA-C32 disk array. Connect the other end of the
power cable to an electrical outlet.
4. Turn on the drive.
5. You will need to uninitialize the drive before changing RAID settings. To do this,
follow the instructions for your Operating System below. (Mac OSX users, see
directly below. Windows users, see page 9) If your operating system is not listed,
contact customer service for assistance.
Mac OS X
a. Go to top menu “Go” and select “Utilities”. The Utilities window opens. Select
“Disk Utility” to start the disk utility program.
4
b. Click the header on the left which starts with the drive size in gigabytes (1). Now
click on the “partition” tab on top (2). Disk Utility will switch to it’s partitioning
function pane. Now click on the dual arrow button under “Volume Scheme” (3).
Choose “1 partition” (4).
5
c. Now click on “Options” under the partition graph (1). The partition scheme type
selection window will pop up. Make sure the selection is “Apple Partition Map”
(2). Then click “OK” (3). You can leave the format type on the right to “MAC OS
extended (journaled)” (4). Then click “Apply” to start partitioning (5).
d. The warning dialog for partitioning will pop up. Go ahead click “partition”.
6
e. The drive will start partitioning as shown. It should take a minimum of 2 minutes
to finish.
f. You now have a MAC OS extended partition. We can now delete the volume and
clear the drive. Click anywhere on the partition graph representing the partition.
Notice the [+ / -] under the graph on the lower left. Click the [-] button to delete
the partition.
7
g. The warning dialog for erasing the partition will pop up. Go ahead click
“Remove”.
h. Your drive is now clean of all partitions. Continue to Step 6 (p.12).
8
Windows 2000/XP/NT/Vista
a. Go to the Start Menu. Click on “Run”.
b. The Run dialog box will show up. Enter “cmd” in the text box then press the
<ENTER> key.
9
c. Virtual DOS command console window will start. You will see the blinking cursor
where you can type commands. Now type “diskpart” as shown then press the
<ENTER> key.
10
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Cavalry Magazzinaggio
Cavalry
Cavalry EN-CAUH-B Manuale utente
Cavalry
Cavalry Passio CAXH3701T0 Manuale utente
Cavalry
Cavalry CADA002SA8 Manuale utente
Cavalry
Cavalry CAUR Series Manuale utente
Cavalry
Cavalry CACE3701T0 Manuale utente
Cavalry
Cavalry CAXM3701T0 Manuale utente
Cavalry
Cavalry CAXB Series Manuale utente
Cavalry
Cavalry CAUP25160 Manuale utente
Cavalry
Cavalry CAXE Series Manuale utente
Cavalry
Cavalry CAUQ25100 Manuale utente
Cavalry
Cavalry Computer Drive Manuale utente
Cavalry
Cavalry CADT001U32 Manuale utente
Cavalry
Cavalry CADT001U32 Manuale utente
Cavalry
Cavalry CADA001U32A Manuale utente
Cavalry
Cavalry CAXE Series Manuale utente
Cavalry
Cavalry CADA002SA4 Manuale utente
Cavalry
Cavalry CADA-C32A Series Manuale utente
Cavalry
Cavalry CAUPT25160 Manuale utente
Cavalry
Cavalry CAUC3701T0 Manuale utente
Cavalry
Cavalry CAXB3701T0 Manuale utente
