CHC I80 GNSS Manuale utente

CHC® i80 GNSS Receiver

Quick Tour with LandStar 7

(UHF Rover Mode)

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

1.Prerequisites

Hardware: CHC i80 Kit, Controller Kit, UHF Bar

Antenna (450-470 MHz), Lithium Battery, pole

Software: LandStar 7

2.Steps to set i80 working as

rover in Internal UHF mode with

LandStar 7

2.1 Rover installation

Fix the bar antenna onto the antenna port,

screw the rover receiver on the pole, and

put the Controller adapter in the right

place.

Note: The recommend firmware version of

i80 is 1.3.42 or higher. If not, please contact

local dealer or CHC Support for latest

firmware.

2.2 Rover setting in LandStar 7

1. Power on the receiver

Long press the i80 power button until the

green and blue LED lights are on.

2. Launch the LandStar 7 software

3. Click [Projects] icon in [Project] menu to

create or open a project.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

4. Click [New] to create a new project.

5. Please type in the project name, the

author of the project, which can be left blank,

the time zone of working region.

Then select the [Coordinate System] to

choose the coordinate system of the project.

In the CRS selection menu, please click [Add]

button to add pre-define coordinate system in

the list.

Select the Continent and Region according to

working area, then find proper Coordinate

System to use.

After select Coordinate System, please click

[Select] button to confirm.

Then selected coordinate system is available

in the pre-define list, please click [Select]

button to confirm.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

After that, user can confirm parameters of

coordinate system.

Please click [Accept] button to finish the

coordinate system selecting.

6. Click [OK] button to finish the project

setting.

7. Click [Config] tab then click [Connect]

icon to enter the connection interface.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

8. i80 receiver supports two kinds of

connection method in LandStar 7: Bluetooth

and WiFi. Please select the proper one to

connect.

Bluetooth connection

(1) Select [Manufacturer] as CHC, [Device

Type] as i80, [Connection Type] as Bluetooth,

[Antenna Type] as i80. Then click the

bluetooth icon on the right side to select the

bluetooth device.

(2) Please click [Bluetooth Manager] to

search bluetooth device around.

If there are several paired bluetooth devices ,

users can directly select them in list.

(3) Switch on the Bluetooth module by the

top switch, click [Search for devices] to search

the bluetooth device around. Then select the

target device in the list.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

(4) Please click [Pair] to connect the

bluetooth device.

(5) Then the device can be selected in the

bluetooth manager list.

(6) Click [Connect] button to build the

connection.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

WiFi connection

(1) Select [Manufacturer] as CHC, [Device

Type] as i80, [Connection Type] as WiFi,

[Antenna Type] as i80. Then click the Wireless

Lan icon on the right side to select the

hot-spot.

(2) Switch on the WiFi module by the top

switch, click refresh button to search the hot

spot around. Then select the target device in

the list.

(3) Please click [Connect] to link to the hot

spot.

If the first time connection to this hot spot,

user may type in the password and the the

default password of i80 WiFi is 12345678.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

(4) Then click the [Connect] button to build

the connection.

9. Click [Config]-[Work Mode] to create or

accept a work mode.

10. Click [New] button to create a work

mode.

11. Please select the work mode as Auto

Rover, Datalink as Radio, Datalink as Radio

then LandStar 7 will read receiver’s available

UHF parameters automatically. Set protocol as

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

Transparent, Step Value as 25KHz.

Set the channel 5.

Note: Please keep base and rover in the

same protocol and frequency or rover cannot

get the correction from base.

Other radio parameters can be set according

to the work condition.

After setting, please click [Save] button to

save the work mode.

12. A name is necessary for a work mode,

user can type in the name as their wish.

13. Now, the work mode is available in the

list. Please select the work mode then click

[Accept] button.

i80 GNSS Receiver Quick Tour with LandStar 7 (UHF Rover)

14. Then the green LED will flash and the

states will come into [Fix], which means the

rover is getting the correction data from base.

15. Please click the [Survey]-[Map] to start

the survey job.

16. Please click the Survey button to collect

the points.

Altri manuali per i80 GNSS

Indice

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente

CHC i80 GNSS Manuale utente

Manuali Ricevitore popolari di altre marche