Chicago Electric 91007 Manuale utente

HAMMER DRILL / DRIVER

18 VOLT

Model 91007

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures, parts list and as-

sembly diagram. Keep your invoice with this manual. Write the invoice number

on the inside of the front cover. Keep this manual and invoice in a safe and dry

place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

SKU 91007 PAGE 2

Item Description

Electrical Requirements Power Source: 18 VDC Battery

Battery Type: 1.7 AH Rechargeable

Charge Time: 1-1/2 Hr

Charger Input: 120 VAC / 60 Hz

Charger Output: 18VDC/500 mA

Drill RPM: 0-350 (Low) / 0-1100 (High)

Hammer Drill BPM: 0-4800 (Low) / 0-16000 (High)

Chuck Type 1/2” Keyless

Trigger Switch Type Variable Speed / Reversible

Accessories Battery Charger / Drill Bits (Set of 6)

Hex Drivers (Set of 6) / Hex Driver Extension

Carrying Case

Weight 4.80 Lbs. With Battery

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from

debris such as sparks. Provide barriers or shields as needed.

ELECTRICAL SAFETY

4. Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter

plugs. Check with a qualified electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away

from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is

wider than the other). This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates the need for the

three wire grounded power cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators,

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools

or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords immedi-

ately. Damaged Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These extension cords are rated for outdoor use, and

reduce the risk of electric shock.

PERSONAL SAFETY

10. Stay alert. Watch what you are doing, and use common sense when oper-

ating a power tool. Do not use a power tool while tired or under the influ-

ence of drugs, alcohol, or medication. A moment of inattention while operat-

ing power tools may result in serious personal injury.

SKU 91007 PAGE 3

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

12. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Carrying power tools with your finger on the Power Switch, or plugging in

power tools with the Power Switch on, invites accidents.

13. Remove adjusting keys or wrenches before turning the power tool on. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

14. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the power tool in unexpected

situations.

15. Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

TOOL USE AND CARE

16. Use clamps (not included) or other practical ways to secure and support

the workpiece to a stable platform. Holding the work by hand or against your

body is unstable and may lead to loss of control.

17. Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

18. Do not use the power tool if the Power Switch does not turn it on or off.

Any tool that cannot be controlled with the Power Switch is dangerous and must

be replaced.

19. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

20. Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

21. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until

repaired.

SKU 91007 PAGE 4

22. Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool’s operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly main-

tained tools.

23. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

24. Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

25. When servicing a tool, use only identical replacement parts. Follow

instructions in the

“Inspection, Maintenance, And Cleaning”

section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of electric shock or injury.

GROUNDING

SKU 91007 PAGE 5

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualfified electrician if you are in doubt as to whether the

outlet is properly grounded. Do not modify the power cord plug provided with

the tool. Never remove the grounding prong from the plug. Do not use the

tool if the power cord or plug is damaged. If damaged, have it repaired by

a service facility before use. If the plug will not fit the outlet, have a proper

outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of elec-

tric shock. (See Figure A, next page.)

2. The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached

to an electrically “live” terminal. (See Figure A.)

3. Your tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration. (See Figure A.)

FIGURE A

SKU 91007 PAGE 6

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4. The Charger for this Hammer Drill/Driver has a 2-Prong Plug, is marked

“Double Insulated”, and does not require grounding. The Charger has a

special double insulation system which satisfies OSHA requirements and com-

plies with the applicable standards of Underwriters Laboratories, Inc., the

CanadianStandard Association, and the National Electrical Code.

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

FIGURE B

SKU 91007 PAGE 7

EXTENSION CORDS

Grounded

tools require a three wire extension cord.

Double Insulated

tools

can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool damage.

(See Figure C.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure C.)

4. If using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Figure C.)

5. If you are using one extension cord for more than one tool, add the nameplate

amperes and use the sum to determine the required minimum cord size.

(See Figure C.)

6. If you are using an extension cord outdoors, make sure it is marked with the

suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified

electrician before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or

wet areas.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(

At Full Load

)

EXTENSION CORD LENGTH

Feet 50

Feet 75

Feet 100

Feet 150

Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop

to five volts at 150% of the rated amperes.

FIGURE C

FIGURE D

SKU 91007 PAGE 8

SYMBOLOGY

Double Insulated

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current

Amperes

No Load Revolutions

per Minute (RPM)

noxxxx/min.

V ~

SPECIFIC SAFETY RULES

1. Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of

obstructions, grease, oil, trash, and other debris. Do not use the Hammer Drill/

Driver in areas near flammable chemicals, dusts, and vapors.

2. Maintain labels and nameplates on the Hammer Drill/Driver. These carry

important information. If unreadable or missing, contact Harbor Freight Tools for

a replacement.

3. When using a hand-held power tool, always maintain a firm grip on the tool

with both hands.

4. To avoid electrical shock, do not pull or carry the Battery Charger (33) by

its Power Cord or pull the Power Cord around sharp corners or edges. Do

not unplug the Battery Charger by pulling on the Power Cord. Keep the Power

Cord away from heated surfaces.

5. Never leave the Battery Charger unattended when it is plugged into an

electrical outlet. Make sure to unplug the Battery Charger from its outlet before

leaving the work area.

6. Use eye protection. Always wear ANSI approved safety impact eye goggles

when working with this product.

7. Proper Battery Care: Battery (28) leakage may occur under extreme usage or

temperature conditions. If Battery fluid comes in contact with skin, wash with

soap and water and rinse with lemon juice and vinegar. If the fluid comes in

contact with eyes, flush with water for several minutes and contact a doctor

immediately. Never burn the Battery, as it can explode in a fire. Do not attempt

to charge a leaking Battery. Contact local solid waste authorities for instructions

on correct disposal or recycling of the Battery.

8. Do not allow children to handle or play with this product.

9. Store idle equipment. When not in use, tools and equipment should be stored

in a dry location to inhibit rust. Always lock up tools and equipment, and keep out

of reach of children.

10. Do not use this product if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgement or reflexes are

impaired while taking drugs. If there is any doubt, do not attempt to use this

product.

11. Industrial applications must follow OSHA requirements.

12. Maintain this product with care. Keep this product clean and dry for better and

safer performance.

13. Maintenance: For your safety, service and maintenance should be performed

regularly by a qualified technician.

14. Check for damaged parts. Before using this product, carefully check that it will

operate properly and perform its intended function. Check for damaged parts

and any other conditions that may affect the safe operation of this product. Re-

place or repair damaged or worn parts immediately.

15. Replacement parts and accessories: When servicing, use only identical re-

placement parts. Only use accessories intended for use with this product.

16. Use the right tool or attachment for the right job. Do not attempt to force a

small tool or attachment to do the work of a larger industrial tool or attachment.

There are certain applications for which this product was designed. It will do the

job better and more safely at the rate for which it was intended. Do not modify

this product, and do not use this product for a purpose for which it was not

intended.

17. Always switch to a fresh Battery when tool performance begins to dimin-

ish. Severe heat is most destructive to a Battery. The more heat generated, the

faster the Battery loses power. A Battery that gets too hot can be permanently

damaged. Never over-discharge a Battery by using the tool even after tool

SKU 91007 PAGE 9

SKU 91007 PAGE 10

18. Do not charge the Battery when the temperature is below 50 degrees

Fahrenheit or above 104 degrees Fahrenheit.

19. Do not allow anything to cover or clog the Battery Charger vents.

20. Do not short the Battery. Do not touch the terminals of the Battery with any

conductive object. Avoid storing the Battery in a container with other metal

objects.

21. Do not store the Hammer Drill/Driver in locations where the temperature

reaches or exceeds 122 degrees Fahrenheit.

22. Do not incinerate the Battery, even if it is severely damaged or worn out.

The Battery can explode in a fire. Contact local hazardous waste disposal

authorities for proper Battery disposal guidelines.

23. Do not shake, drop, or strike the Battery.

24. Charge the Battery in a well ventilated area.

25. Plug the Battery Charger Plug only into a 120 volt, grounded, electrical

outlet.

26. Always disconnect the Hammer Drill/Driver from its Battery and the Battery

Charger from its electrical outlet before performing any services or

maintenance on the tool. Make sure to unplug the Hammer Drill/Driver and

Battery Charger when cleaning the equipment, moving them to a different work

location, handing the equipment to another person, etc.

performance is decreasing. Never attempt to discharge a tool’s Battery by con-

tinuing to pull the tool trigger. When tool performance begins to diminish, stop

the tool, re-charge the Battery, and use the fresh Battery for optimal performance.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities, contain chemicals known [to the State of California] to cause can-

cer, birth defects or other reproductive harm. Some examples of these chemicals are: A)

Lead from lead-based paints, B) Crystalline silica from bricks and cement or other ma-

sonry products, C) Arsenic and chromium from chemically treated lumber. Your risk from

these exposures varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals:work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic

particles. (California Health & Safety Code 25249.5,

et seq.

)

27. WARNING! People with pacemakers should consult their physician(s)

before using this product. Operation of electrical equipment in close proximity to

a heart pacemaker could cause interference or failure of the pacemaker.

28. WARNING! The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

Indice

Altri manuali Chicago Electric Trapano

Chicago Electric

Chicago Electric 60495 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 68169 Manuale di installazione

Chicago Electric

Chicago Electric 67089 Manuale di installazione

Chicago Electric

Chicago Electric Chicago 44849 Manuale del proprietario

Chicago Electric

Chicago Electric 3670 Manuale utente

Chicago Electric

Chicago Electric 93449 Manuale utente

Chicago Electric

Chicago Electric 1/2" variable Speed Reversible HEAVY DUTY DRILL... Istruzioni per il montaggio

Chicago Electric

Chicago Electric 47991 Manuale di installazione

Chicago Electric

Chicago Electric ITEM 62427 Manuale utente

Chicago Electric

Chicago Electric 93632 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 95877 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 93142 Manuale utente

Chicago Electric

Chicago Electric 45338 Manuale utente

Chicago Electric

Chicago Electric 45790 Manuale utente

Chicago Electric

Chicago Electric 69360 Manuale di installazione

Chicago Electric

Chicago Electric 46804 Manuale utente

Chicago Electric

Chicago Electric 98179 Manuale di installazione

Chicago Electric

Chicago Electric 93632 Manuale utente

Chicago Electric

Chicago Electric 47991 Manuale elenco delle parti

Chicago Electric

Chicago Electric 93632 Manuale di istruzioni

Chicago Electric

Chicago Electric 98179 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 65756 Manuale di installazione

Chicago Electric

Chicago Electric 66127 Manuale di installazione

Chicago Electric

Chicago Electric 69452 Istruzioni per il montaggio

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente