Chicago Electric 93449 Manuale utente

30V Cordless

Hammer Drill Kit

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

93449

Due to continuing improvements, actual product may differ slightly from the product described herein.

SKU 93449

For technical questions please call 1-800-444-3353

Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in

damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not

use electrically powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. It will do the job better

and more safely at the rate for which it was intended. Do not modify this

tool and do not use this tool for a purpose for which it was not intended.

:snoitcnuF ,llirDremmaHsseldroC

revirdwercSrollirDlanoitnevnoC :noitcurtsnoC htiwgnisuoHraeGmunimulA

yrett

aBelbavomeR

:ylppuSrewoP yrettaBCDV03elbaegrahceR

kcaP :tinUgnigrahCregrahCkciuQruoh½-1CAV021

:sgnitteSeuqr

oT/hctulC

sgnittesedoMllirDelbairav8

edoMremmaH

elbisreveRsirotoM

:deepSrotoM

raeGwoLnimpr063-0

raeGhgiHnim

pr092,1-0

raeGwoLnimpb082,5-0

raeGhgiHnimpb002,91-0

:yticapaCkcuhC"2/1ot"61/1:thgieWteNyrettaBhtiw.sbL59.6

REV 04/06

SKU 93449

For technical questions please call 1-800-444-3353

Page 3

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught

in moving parts. Protective, electrically non-conductive clothes and nonskid

footwear are recommended when working. Wear restrictive hair covering to

contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety

goggles. Wear a full face shield if you are producing metal filings or wood

chips. Wear an ANSI approved dust mask or respirator when working around

metal, wood, and chemical dusts and mists.

8. Do not overreach. Keep proper footing and balance at all times. Do not

reach over or across running machines.

9. Maintain tools with care. Keep tools maintained and clean for better and

safer performance. Follow instructions for lubricating and changing

accessories. Inspect tool cords periodically and, if damaged, have them

repaired by an authorized technician.The handles must be kept clean, dry,

and free from oil and grease at all times.

10. Disconnect power. Unplug Battery Charger when not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting

wrenches are removed from the tool or machine work surface before

plugging it in.

12. Avoid unintentional starting. Be sure the switch is in the Off position when

not in use and before plugging in. Do not carry any tool with your finger on

the trigger, whether it is plugged in or not.

13. Stay alert. Watch what you are doing, use common sense. Do not operate

any tool when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment and binding of moving

parts; any broken parts or mounting fixtures; and any other condition that may

affect proper operation. Any part that is damaged should be properly repaired

or replaced by a qualified technician.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known [to the State of California] to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

Lead from lead-based paints

Crystalline silica from bricks and cement or other masonry products

Arsenic and chromium from chemically treated lumber

(California Health & Safety Code 25249.5,

et seq.

)

SKU 93449

For technical questions please call 1-800-444-3353

Page 4

15. Guard against electric shock. Prevent body contact with grounded surfaces

such as pipes, radiators, ranges, and refrigerator enclosures.

16. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool. Approved accessories are

available from Harbor Freight Tools.

17. Do not operate tool if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reflexes are

impaired while taking drugs. If there is any doubt, do not operate the tool.

18. Maintenance. For your safety, service and maintenance should be performed

regularly by a qualified technician.

19. Pacemaker safety warning. People with pacemakers should consult with

their physician(s) before using this product; operation of equipment in close

proximity to a heart pacemaker could cause interference or failure of the

pacemaker.

Note: Performance of the charger may vary depending on variations in local line volt-

age. Extension cord usage may also affect tool performance.

Warning: The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may oc-

cur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by

the operator.

SKU 93449

For technical questions please call 1-800-444-3353

Page 5

Unpacking

When unpacking, check to make sure that the product is intact and undamaged,

and all accessories listed below are

included.

1/2” Drive Cordless Hammer Drill

(2) Rechargeable Batteries

Auxiliary Handle with Depth Gauge

Quick Charge Battery Recharge Unit

Plastic Storage Case

If any parts are missing or broken, please

call Harbor Freight Tools at the number

on the cover of this manual.

Using the Battery Charger

NOTE: Battery Packs will not reach full charge the first time they are charged.

Allow several cycles (operation followed by recharging) before the Battery Pack will

become fully charged.

Battery Temperature Warning:

WARNING: Battery explosion may cause

serious personal or property injury

including death. Charge the Battery Pack

only within a 50° to 100° F. temperature

range. Lower temperatures may inhibit

charging. Higher temperatures increase

chance of battery failure, including

explosion.

Battery Charger Safety:

1. Charge the Battery Pack only with

the included charger. Use of other

chargers may cause battery failure

including explosion.

2. Ensure that the Battery Charger is connected only to a 120 VAC, 60 Hz power

supply that includes a circuit breaker.

Using the Battery Charger

SKU 93449

For technical questions please call 1-800-444-3353

Page 6

Working with the Rechargeable Battery

Charging the Battery Pack:

1. Battery Packs are normally shipped with low or no charge to prevent potential

problems during shipment. Before use, you must charge your new Battery Pack.

Initial charge time is approximately 1-½ hour. Subsequent recharge time is

approximately 1-½ hour. New Battery Packs will not hold a charge as long as

older ones. Completely deplete and recharge Battery Pack several times to

extend its charge life.

2. Plug the battery charger into a 120 VAC, 60 Hz power outlet, the Green LED will

illuminate.

3. Insert the Battery Pack into the charger by aligning the rib on the Battery Pack

with the groove in the charger. Press the Battery Pack into place. The Green

LED will shut off and the Red LED will illuminate indicating that a Battery Pack

is installed in the charger, and that it has started charging.

NOTE: During recharging, the Battery Pack will become slightly warm to the touch.

This is normal and not a cause for concern. Do not keep the Battery Pack or

charger in an environment of extreme heat or cold. They will work best at room

temperature.

4. The red LED will remain on for approximately 1 hour while the Battery Pack

charges. When the Battery Pack is fully charged the Red LED will go out, and

the Green LED will illuminate indicating that the Battery Pack is fully charged.

5. When the Battery Pack is fully charged, remove the charged battery from the

charger, and unplug the charger from its power source. Put the charger away for

safekeeping. Do not leave the Battery Pack in the charger indefinitely.

Installing the Battery Pack

1. Slide the Battery Pack onto the rail of

the body before pressing it into the

handle. CAUTION: Do not press the

battery into the handle if it is not

properly aligned on the rail, as this may

damage the body of the tool, and will

not secure the battery.

2. With the Battery Pack properly

aligned on the rail, press into place

in the handle.

Installing the Battery Pack

SKU 93449

For technical questions please call 1-800-444-3353

Page 7

Using the Battery Lock and Removing the Battery Pack

1. After placing the Battery Pack in the tool a Battery Lock engages to prevent

the battery from coming out accidentally.

2. To remove the Battery Pack, depress the Battery Lock and the Battery

Release buttons as shown in the photo below.

3. Remove the Battery Pack from the tool.

Hammer Drill Controls

1. Before inserting the Battery Pack into the tool, check to be sure that the

Trigger operates properly, and returns to the OFF position when released.

2. Use only fully charged Battery Pack specifically designed for this tool. Insert

the Battery Pack into the handle. Ensure that the Battery Lock is engaged

securely holding the Battery Pack in place.

SKU 93449

For technical questions please call 1-800-444-3353

Page 8

Operation

For use as a Hammer Drill:

CAUTION: Use only impact grade bits, designed for hammer drills. Standard bits may

break under the force created by this tool. Impact grade bits are available from

Harbor Freight Tools.

1. The Auxiliary Handle must be installed for additional stability when Hammer

Drilling. Always use both hands to hold this tool during hammer drill

operation. To install Axillary Handle, loosen the screw on the side of the assembly.

Slide the Auxiliary Handle assembly over the aluminum portion of the tool, as

shown in the photograph. Adjust the length of the Depth Gauge Rod to stop the

drilling process when the correct hole depth is reached.Tighten the assembly in

place by turning the handle

clockwise. The handle may be

installed on either the right or left

side of the tool.

2. Select and install an appropriate drill

bit. Do this by opening the jaws of

the Chuck using the Chuck Key.

Insert the butt end of the drill bit

into the center of the Chuck. Rotate

the Chuck to close the Jaws on the

drill bit. Be sure that the bit is

centered in the Chuck Jaws.

Tighten in place using the Chuck

Key.

3. Move the Torque Selection Ring to

the Hammer Drill setting. Please see picture on page 7 for reference.This setting

will allow the drill to hammer as well as turn.

4. This tool has two Gear Settings, Low and High. Please refer to photo on page 7.

With the Gear Selector moved forward in High position the maximum blows per

minute is 19,200 BPM and rotation is 1,290 RPM. With the selector back in the

Low position, the maximum speed is 5,280 BPM and 360 RPM.

5. The Hammer Drill is best suited for drilling into hard materials such as concrete

or masonry. Select an appropriate size and type hammer drill bit (not included).

Insert it onto the Chuck and tighten securely. Be sure the drill bit is properly

inserted and tight before proceeding.

Warning: Always wear ANSI approved safety glasses and full face shield when

hammer drilling, as removed material will fly uncontrollably, possibly causing

injury. Caution: Always check around and behind the area being drilled to prevent

drilling into wires, pipes or causing other unintentional property damage.

The Hammer Drill Auxiliary

Handle Assembly

SKU 93449

For technical questions please call 1-800-444-3353

Page 9

4. Position the drill bit at the place to be drilled and squeeze the Trigger. The tool

is variable speed, and will rotate and hammer faster as the Trigger is

progressively squeezed.

5. When the forward end of the Depth Gauge Rod contacts the work surface, you

know the hole is the desired depth. Release the Trigger to stop the operation

of the tool, and withdraw the bit from the hole.

For Use as a Drill:

1. Move the Torque Selection Ring to the Drill setting. Please see picture on

page 7 for reference.This setting will allow the drill to turn but not hammer.

Move the Gear Selector to High or Low.

2. Select and install an appropriate drill bit. Do this by opening the jaws of the

Chuck using the Chuck Key. Insert the butt end of the drill bit into the center

of the Chuck. Rotate the Chuck to close the Jaws on the drill bit. Be sure that

the bit is centered in the Chuck Jaws. Tighten in place using the Chuck Key.

3. Start the drill by squeezing the trigger to be sure that the drill bit is properly

centered in the Chuck.

4. Position the drill bit at the appropriate point on the workpiece and squeeze the

trigger to start the drill operating. The tool is variable speed, and will rotate

faster as the Trigger is progressively squeezed.

5. When the desired depth has been reached, release the Trigger to stop the

operation of the tool, and withdraw the bit from the hole.

NOTE: This tool is reversible. If

the drill bit does not withdraw

easily from the hole, you may

reverse the rotation to help it

come out. With the tool stopped,

press the REV button from left to

right. Then lightly squeeze the

trigger; the drill will operate in

reverse. As needed, stop the

operation of the tool, and press

the REV button from right to left

to reset the drill in forward

rotation position. CAUTION: Do

not press the REV button while

the tool is operating. This will damage the tool.

the REV button

SKU 93449

For technical questions please call 1-800-444-3353

Page 10

For Use as a Screwdriver:

1. Move the Torque Selection Ring to the desired Torque setting, and the Gear

Selector to the desired selection. The Torque Setting will allow the internal

clutch to slip when the desired torque is reached. This will prevent the screw

from being driven too deep into the work material. This also prevents damage

to the tool caused by sudden stops as the screw bottoms out.You should

determine the proper torque setting by drilling several screws into scrap

material before beginning work. A higher number is higher torque.

NOTE: Press the REV button from left to right and then squeeze the trigger to

allow the tool to operate in reverse.

NOTE: Use of a screw holder bit attachment (not included) is recommended to

prevent possible injury to your hand or fingers.

Trouble Shooting

Tool will not operate or operates slowly:

1. Battery Pack may be discharged. Replace Battery Pack with a fresh one, or

recharge the Battery Pack.

2. Too great a load is being placed on the tool. Lighten pressure on workpiece.

Battery Pack loses charge quickly:

1. New Battery Packs will not hold a charge as long as older ones. Completely

deplete and recharge Battery Pack several times to extend its charge life.

Maintenance

1. Keep your tool clean and dry. Wipe dirt and grease from it if it becomes dirty.

2. Do not allow your tool, Battery Packs or Charger to become wet.

3. Do not leave Battery Pack in Charger unattended for long periods of time.

4. When not in use, remove the Battery Pack and store both tool and Battery

Packs in its case in a dry, secure location.

Indice

Altri manuali Chicago Electric Trapano

Chicago Electric

Chicago Electric 1/2" variable Speed Reversible HEAVY DUTY DRILL... Istruzioni per il montaggio

Chicago Electric

Chicago Electric 60495 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 68851 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 67616 Manuale di istruzioni originale

Chicago Electric

Chicago Electric 93632 Manuale di installazione

Chicago Electric

Chicago Electric 60495 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 47991 Manuale di installazione

Chicago Electric

Chicago Electric 66006 Manuale di installazione

Chicago Electric

Chicago Electric 93632 Manuale di istruzioni

Chicago Electric

Chicago Electric 46804 Manuale utente

Chicago Electric

Chicago Electric 47991 Manuale elenco delle parti

Chicago Electric

Chicago Electric 1/2" variable Speed Reversible HEAVY DUTY DRILL... Istruzioni per il montaggio

Chicago Electric

Chicago Electric 98179 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 93632 Manuale utente

Chicago Electric

Chicago Electric 91007 Manuale utente

Chicago Electric

Chicago Electric 69452 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 45790 Manuale utente

Chicago Electric

Chicago Electric 68169 Manuale di installazione

Chicago Electric

Chicago Electric 68856 Manuale utente

Chicago Electric

Chicago Electric 97907 Manuale di installazione

Chicago Electric

Chicago Electric 68126 Manuale di installazione

Chicago Electric

Chicago Electric 69360 Manuale di installazione

Chicago Electric

Chicago Electric 97594 Manuale di installazione

Chicago Electric

Chicago Electric HARBOR FREIGHT TOOLS 98544 Manuale di installazione

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente