Chinowing T21 Manuale utente
1
www.chinowing.com
T21
Handheld Ground Control Station
User Manual V 1.2.7
2019.4
2
www.chinowing.com
Content
目录
1. Disclaimer ...........................................................................................4
2. Product Precautions ...........................................................................4
2.1 Installation Note.....................................................................4
2.2 Precautions for Use................................................................ 5
3. Product Introduction ..........................................................................5
4. Item List ..............................................................................................5
5. Product Instruction ............................................................................ 7
5.1. Airborne unit(receiver) R20 ................................................ 7
5.2. Remote Control Instruction..................................................8
5.3. Receiver R20 Installation and Connection.......................... 9
6. Remote Controller Operation .......................................................... 10
6.1. Power on and Power off of the Tablet .................................10
6.2. Power On and Power Off of the Remote Controller ............ 10
6.3. Indicator Instruction of Remote Controller and Receiver .... 11
7. RC Parameters Setting Software ......................................................12
7.1. Main Interface Instruction .................................................... 12
7.2. Channel Monitoring and Calibration .................................... 13
7.3. Channel Configuration .......................................................... 14
7.4. Throttle Hold .........................................................................19
7.5. Alarm Instructions for remote control ................................. 20
8. Receiver Pairing and Configuration ................................................. 22
8.1. Operation Instruction for H840 Parameters Pairing .............25
8.2. Operation Instruction for H900 Parameters Pairing .............26
9. Charge the Remote Controller .........................................................28
10. HID Controller ................................................................................ 28
11. Common Questions ....................................................................... 31
12. Firmware Upgrading Procedure .................................................... 31
12.1. Firmware version view ........................................................31
12.1. Remote Control Firmware Upgrade ................................... 32
4
www.chinowing.com
1. Disclaimer
Thank you for purchasing the T21 hand-held remote-control station. Please use it in
accordance with local radio control regulations and read this statement carefully before
using it. Once used, it shall be deemed to endorse and accept all contents of this statement.
Please strictly follow this instruction to install and use the product. The supplier will not
bear any legal liability for any result or loss caused by improper use, installation, final
assembly or modification of the product.
2. Product Precautions
1) T21 ground unit is matched with airborne unit R20 to use together.
2) The ground unit is with built-in 12v battery (3S lithium battery). The airborne end
needs external power input DC7.4-12V(2S-3S lithium battery). Please power the system in
strict accordance with specifications.
3) With improper operation, the aircraft may cause a certain degree of injury and damage
to human and the system, please be sure to pay attention to safety during use.
4) In order to better serve customers, our R&D team has been upgrading and optimizing
the product. The software and firmware will be upgraded frequently. There may be
incompatibilities between different firmware versions. Please pay attention to asking the
supplier for the latest software firmware and technical support.
5) Software and firmware version example: calling software: HZY_ToolBench V1.2.3.4;
Ground end firmware: TTX 30-1.2.3-1.0; airborne end R20 firmware: RSx16-1.2.3-1.0;
airborne end V20 firmware: V20RX-1.2.3-1.00.
6) The software, firmware, drivers, port conversion tools, etc. involved in this manual will
be updated from time to time on our website, please visit our website to download, or
contact us for more information.
7) If you encounter any problem that cannot be solved during installation or use of the
product, please contact us or visit our web www.chinowing.com
2.1 Installation Note
1) Be sure to use the spare parts provided by our company.
2) Be sure to install the antennas before power on to avoid damage to the circuit.
5
www.chinowing.com
3) Try to make the receiver antenna without obstruction, and the end part of the antenna is
vertically downward without bending, so as to avoid shortening the communication
distance or even failing to communicate due to obstruction.
4) Do not disassemble or refit without permission. If you encounter any problem that
cannot be solved during installation, please contact us directly.
5) During installation, keep proper distance between electronic devices to minimize
electromagnetic interference.
2.2 Precautions for Use
1) Before use, please make sure that all connection wires are fastened reliably and all parts
work normally.
2) Please open the configuration software of the remote control and check whether the
channels are normal.
3) Please check the surrounding environment to ensure that there is no interference from
other devices, otherwise T21 data transmission performance will be seriously affected.
4) Check the power of the remote control before use. If the parameter adjustment software
shows that power is low, please charge the remote control timely. If the remote control is
turned off, the receiver has entered the state of Fail-safe protection. Stop using it when the
battery is too low. Don't rely on the device's low-power alarm, which is only a precaution
and tells you when to charge. It takes about 5hs to be fully charged.
3. Product Introduction
T21 is a highly integrated system of remote controller, data link and ground control station.
With the compact size, easy operation, T21 has 16 adjustable Channels and dual SBUS
output, able to control the dorne and the payload simultaneously. Working under the
frequency of 840MHz/900MHz, it can transmit stable data at the max range of 30km. It has
been widely used in UAV, UGV, USV, etc.
4. Item List
Main module
Remote controller x1
Airborne unit(receiver) x1
6
www.chinowing.com
Accessories
Power supply
cable*1
Charger*1
Receiver upgrade
configuration
line*1
Lan-to-4 pins
line*1
Power for receiver
(DC:7.4-12V, Li
battery 2s-3s)
Charge for remote
controller
Used for firmware
upgrading
and parameters
setting for receiver
For module
Parameter
configuration
7
www.chinowing.com
5. Product Instruction
5.1. Airborne unit(receiver) R20
①Power supply interface: pls use XT30 plug to power, power supply: 7.4-12v
②COM port: TTL, used for connecting COM port or API prot of flight controller
③S-BUS1 interface: to connect flight controller or other devices
④S-BUS2interface: to connect flight controller or other devices
⑤Signal strength indicator: S3 ON, signal is weak; S3 and S2 ON, signal is moderate; S3, S2
and S1 ON, signal is strong.
⑥Data transmission indicator: RXD indictor ON means there is data receiving of the receiver;
TXD indictor ON means there is data transmitting of the receiver.
⑦S-BUS data indicator L1: used for indicating the communication status of remote
controller and receiver
⑧Receiver configuration mode indicator L2: used for indicating whether it is in the
confinguration mode
⑨SET button: frequency modulation button between remote controller and receiver
By default, the S-BUS1 and S-BUS2 interfaces output the CH1 to CH16 of the
remote control to 1-16 channels.
1
②
③
④
⑤
⑥
⑦
⑧
⑨
8
www.chinowing.com
5.2. Remote Control Instruction
①RC power button: turn on or turn off RC
②⑪Small joysticks: corresponding T5, T6, T7, T8, used for controlling gimbal or other
devices
③⑩ Large joysticks: used for controlling the flight(4 kinds of joystick mode can be set by
the parameters setting software)
④⑨Knob: LD&RD
⑤⑧Three-position switch: SA&SB
⑥Tablet power button: used for turn on or turn off tablet
⑦Charing indicator of tablet: used for indicating power status of tablet
⑫Type-C charging port: powering for tablet, Max charging current 3A
⑬Standard USB interface: used for externally connecting USB keyboard, mouse or USB flash
disc, etc
⑭⑰button: SF&SC
⑮⑯Three-position switch: SE&SD
⑧
③
⑩
1
②
④
⑤
⑥
⑦
⑨
○
11
○
12
○
13
○
14
○
15
○
16
○
17
9
www.chinowing.com
5.3. Receiver R20 Installation and Connection
1. Connecting antennas to SMA port of Rx.
2. Fix the receiver to the appropriate position of the aircraft by using double-sided tape.
3. As shown in the above photo, connecting COM port and S-Bus port of the R20 receiver to
your device by lead wire of servo.
RX
TX
S
S
Receiver GND
GND Flight controller, etc
Receiver +
+ Flight controller,
etc
TX
RX
-
-
4. With 7.4-12v DC power input, L1 indicator will flicker. That means the success
connection of transmitter and remote control.
5. If you are using a dual S-Bus receiver, both S-Bus1 and S-Bus2 output CH1 to CH16 from
the remote control. And the output of S-Bus1 and S-Bus 2 can be mapped separately. See
the output mapping description.
Flight controller
Other devices
to receive
SBUS signal
10
www.chinowing.com
The default power of the receiver: 1W. Please keep the antenna away from other
electronic devices (GPS, compass, etc.) to avoid interference.
Be sure to install the antenna before power on, otherwise it may burn out the radio
module.
When using, try to make the antenna face down and without any obstacle to block,
so as to avoid the communication distance being shortened due to blocking, or even unable to
communicate.
Be sure to use the specified type of antenna and install it correctly. Do not use other
types of antennas.
6. Remote Controller Operation
6.1. Power on and Power off of the Tablet
1. Long press the power button. Release it when you see the power-up screen.
2. After the computer is turned on, you can check the remaining battery power through
indicator icon in the lower right corner of the desktop. If less than 20% power, please
charge timely.
3. After finishing the operation, pls power off the computer through the computer shutdown
interface.
When you do not use your computer for a long time, please turn it off in time to avoid
the power consumption.
If it is found that the long press the power button cannot start up the system, it is
likely that the battery is with low capacity. Please charge it by standard adapter.
6.2. Power On and Power Off of the Remote Controller
Power on: long press for 5s
Power off: long press for 5s
Indice
Altri manuali Chinowing Sistema di controllo
