Cisco ATA 191 Manuale di istruzioni

Install the ATA 191

•ATA 191 Installation Information, page 1

•Network Requirements, page 1

•Safety Recommendations, page 2

•Package Contents, page 2

•Install Your Cisco ATA , page 2

•Attach a Phone to the ATA 191, page 3

•Startup Process Verification, page 3

•Configure Startup Network Settings, page 4

•Security on the ATA 191, page 4

ATA 191 Installation Information

You connect the ATA 191 hardware and configure the ATA 191 by loading the QED and firmware files.

Install the QED file first, then install the firmware file. For more information about loading the QED and

firmware files, see the "Installation Notes" section of the "Release Notes for Cisco ATA 191 Analog Telephone

Adapter".

Network Requirements

The ATA 191 acts as an endpoint on an IP telephony network. The following equipment is required:

•Call Control system

•Voice packet gateway—Required if you are connecting to the Public Switched Telephone Network

(PSTN). A gateway is not required if an analog key system is in effect.

•Ethernet connection

Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager

Safety Recommendations

To ensure general safety, follow these guidelines:

•Do not get this product wet or pour liquids into this device.

•Do not open or disassemble this product.

•Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

•Use only the power supply that comes with the ATA.

•Ultimate disposal of this product should be handled according to all national laws and regulations.

•Read the installation instructions before you connect the system to its power source.

•The plug-socket combination must always be accessible because it serves as the main disconnecting

device.

•Do not work on the system or connect or disconnect cables during periods of lightning activity.

•To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network

voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some

LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

For translated warnings, see the Regulatory Compliance and Safety Information for the Cisco ATA 191

document.

Package Contents

The ATA 191 package contains the following items:

•Cisco ATA 191 Analog Telephone Adapter

•Regulatory Compliance and Safety Information for the ATA 191

•5V power adapter with appropriate country clip

•Ethernet cable

The ATA is intended for use only with the 5V DC power adapter that comes with the

unit.

Note

Install Your Cisco ATA

You can use either Category 3/5/5e/6 cabling for 10-Mbps connections, but you must use Category 5/5e/6 for

100-Mbps connections.

Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager

Install the ATA 191

Safety Recommendations

Procedure

Step 1 Connect the power supply to the Cisco DC Adapter port.

Step 2 Connect a straight-through Ethernet cable from the network to the network port on the ATA. Each ATA ships

with one Ethernet cable in the box.

Attach a Phone to the ATA 191

Before You Begin

You can attach one or two phones to an ATA 191.

Procedure

Connect one or more phones to a phone port of the ATA with an RJ11 cable.

The PHONE1 and PHONE2 LEDs on the ATA light as solid green when there is activity on that port.

Startup Process Verification

After your ATA has power connected to it, it begins the startup process by cycling through these steps:

1The Power LED flashes during the startup process.

2The Problem Report Tool (PRT) LED lights solid amber during initial bootup. The LED then flashes

amber and then green while the application and kernel are booting.

If the PRT LED lights red during bootup, then either the MIC certificate failed, or the ATA failed to obtain

a network address.

3The LED for Phone 1 flashes while the Phone1 port boots, followed by the LED for Phone 2.

After the Phone1 and Phone2 ports register with Cisco Unified CM successfully, the corresponding LEDs

are lit with solid green. If a phone port fails to register, the LED rapidly flashes in green three times, then

repeats.

4When the ATA has successfully booted, the Power LED lights solid green and the PRT LED turns off.

The Network LED flashes as traffic is detected.

When you go offhook on the phone, the phone LED begins to flash, and you hear the dial tone. The ATA has

completed the startup process.

Related Topics

Start up Process with Standby Image

Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager

Install the ATA 191

Attach a Phone to the ATA 191

Configure Startup Network Settings

Before You Begin

Perform this configuration if you are not using DHCP in your network.

Procedure

Step 1 Configure these network settings on the ATA after you install the device on the network:

•IP subnet information (subnet mask and gateway)

•TFTP server IP address

Step 2 Configure these optional settings as necessary:

•Administration VLAN ID

Step 3 Collect this information.

Security on the ATA 191

Security features protect against several threats, including threats to the identity of the phone and to data.

These features establish and maintain authenticated communication streams between the phone and the Cisco

Unified Communications Manager server, and digitally sign files before they are delivered.

For more information about the security features, see the Security Guide for Cisco Unified Communications

Manager.

You can start the installation of a Locally Significant Certificate (LSC) on the device profile from Cisco

Unified Communications Manager. Use the Device >Phone >Phone Configuration menu option. You can

also use this menu option to update or remove an LSC.

Before you begin, make sure that the appropriate Cisco Unified Communications Manager and the CAPF

security configurations are complete:

•On Cisco Unified Communications Operating System Administration, verify that the CAPF certificate

has been installed.

•The CAPF is running and configured.

See the Security Guide for Cisco Unified Communications Manager for more information.

Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager

Install the ATA 191

Configure Startup Network Settings

Altri manuali per ATA 191

Indice

Altri manuali Cisco Adattatore

Cisco

Cisco Linksys WUSB54G Istruzioni operative originali

Cisco

Cisco SPA100 Series Manuale di istruzioni

Cisco

Cisco AIR-PCM352 - Aironet 350 Series 11Mbps Wireless LAN PC Card... Manuale dell'operatore

Cisco

Cisco LINKSYS USB1000 Manuale utente

Cisco

Cisco iDTA153 Manuale utente

Cisco

Cisco WUSB54GC-RM - Refurb Wireless-g Compact USB Manuale utente

Cisco

Cisco SPA112 Manuale utente

Cisco

Cisco AIR-PCI340 Manuale dell'operatore

Cisco

Cisco SPA122 Manuale utente

Cisco

Cisco AIRONET CB21AG Manuale dell'operatore

Cisco

Cisco SPA112 Manuale utente

Cisco

Cisco PLE300 Manuale utente

Cisco

Cisco PLE300 Manuale utente

Cisco

Cisco Cisco Aironet Wireless LAN Client Manuale dell'operatore

Cisco

Cisco SPA122 Manuale utente

Cisco

Cisco Linksys AE1200 Istruzioni per l'installazione e il funzionamento

Cisco

Cisco ATA 191 Manuale utente

Cisco

Cisco Linksys SPA 2102 Manuale utente

Cisco

Cisco LINKSYS PLK200 Manuale utente

Cisco

Cisco PA-5EFL= Manuale dell'operatore

Cisco

Cisco ATA 186 Manuale di istruzioni

Cisco

Cisco PA-2FE-TX Istruzioni operative e di manutenzione

Cisco

Cisco PA-E3 Series Istruzioni operative e di manutenzione

Cisco

Cisco WPC54G Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente