Cisco T3 Guida rapida

CHAPTER

20-1

Cisco Network Modules Hardware Installation Guide

OL-2485-20

Connecting T3/E3 Network Modules

This chapter describes how to connect T3/E3 network modules for modular access routers and contains

the following sections:

•1-Port T3/E3 Network Modules, page 20-1

•Connecting T3/E3 Network Modules to the Network, page 20-2

•T3/E3 Network Module LEDs, page 20-3

•Related Documents, page 20-3

Tip To determine whether your router supports a specific network module, see Table 1-6 on page 1-16.

1-Port T3/E3 Network Modules

The NM-1T3/E3 network module is a single-port universal T3/E3 network module with integrated

CSU/DSU, clear channel, and subrate support. (See Figure 20-1.) Channels on the network module can

be configured as either T3 or E3 through Cisco IOS software.

Figure 20-1 1-Port T3/E3 Network Module Faceplate

Note The NM-1T3/E3 network module provides subrate T3 support for Digital Link, Kentrox, Larscom,

Verilink, and Adtran. The NM-1T3/E3 network module also provides subrate E3 support for Digital Link

and Kentrox.

SEE MANUAL BEFORE INSTALLING NETWORK MODULE

72536

NM-1T3/E3

LP AIS AL

TX RX

FERF/RAI

T3/E3

20-2

Cisco Network Modules Hardware Installation Guide OL-2485-20

Chapter 20 Connecting T3/E3 Network Modules

Connecting T3/E3 Network Modules to the Network

To connect a T3/E3 network module to the network, use a 75-ohm 728-A coaxial cable to connect the

BNC connector on the network module to a networking device. (See Figure 20-2.)

Warning

This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do

not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11

port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming

call. Statement 1042

Warning

If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port

to a public network that follows the European Union standards. Connecting the port to this type of

public network can cause severe injury or damage your router. Statement 1031

Caution To minimize transient surges, the internal wiring should not be routed in the same conduit with power

lines or external telephone lines.

Figure 20-2 Connecting a T3/E3 Network Module to a Networking Device (Cisco 7603 Router Shown)

72715

SUPERVISOR2

WS-X6K-SUP2-2GE

STATUS

SYSTEM

CONSOLE

PWR MGMT

RESET

CONSOLE

PORT

MODE PCMCIA EJECT

PORT 1 PORT 2

Switch Load

100%

LINK

OSM-4OC12 POS-SI

4 PORT OC-12 POS SM IR

STATUS 1

4RESET

LINK

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

ACTIVE

PORT 1

ACTIVE

PORT 2

ACTIVE

PORT 3

ACTIVE

PORT4

OSM-4OC12 POS-SI

4 PORT OC-12 POS SM IR

STATUS 1

4RESET

LINK

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

ACTIVE

PORT 1

ACTIVE

PORT 2

ACTIVE

PORT 3

ACTIVE

PORT4

SEE MANUAL BEFORE INSTALLING NETWORK MODULE

NM-1T3/E3

LP AIS AL

TX RX

FERF/RAI

T3/E3

TX RX

20-3

Cisco Network Modules Hardware Installation Guide

OL-2485-20

Chapter 20 Connecting T3/E3 Network Modules T3/E3 Network Module LEDs

Tip When connecting the T3/E3 network module to a port adapter used in another router series, verify that

you are connecting the TX port on the network module with the RX port on the port adapter, and the TX

port on the port adapter to the RX port on the network module.

T3/E3 Network Module LEDs

All network modules have an enable (EN) LED. This LED indicates that the module has passed its

self-tests and is available to the router. See Figure 20-3 and Table 20-1 for LEDs on the T3/E3 network

module.

Figure 20-3 T3/E3 LEDs

Related Documents

Cisco IOS Software Documentation

For information on Cisco IOS software features specific to the T3/E3 network module, see the Clear

Channel T3/E3 Network Module with Integrated CSU/DSU document.

Altri manuali per T3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Unità di controllo

Cisco

Cisco NM-1E2W Guida rapida

Cisco

Cisco 6015 Manuale per l'uso e la cura

Cisco

Cisco TelePresence Touch10 Manuale utente

Cisco

Cisco Beacon Point Module Manuale

Cisco

Cisco TelePresence Touch10 Manuale utente

Cisco

Cisco NCS 1004 Manuale utente

Cisco

Cisco 7300-1OC12POS-MM Istruzioni operative e di manutenzione

Cisco

Cisco NM-1CT1 Guida rapida

Cisco

Cisco MEM-CIP-64M Manuale utente

Cisco

Cisco WS-G5484 Manuale utente

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuale di installazione e funzionamento

Cisco

Cisco Catalyst 9400 Series Manuale di installazione e funzionamento

Cisco

Cisco ONS 15200 Manuale utente

Cisco

Cisco CGM-WPAN-OFDM-FCC Manuale utente

Cisco

Cisco Catalyst 5000 Series Manuale utente

Cisco

Cisco SCE8000 GBE Manuale utente

Cisco

Cisco T1 Manuale utente

Cisco

Cisco ASA5506-AP702 Manuale utente

Cisco

Cisco MEM-NP8F Series Guida rapida

Cisco

Cisco GS7000 Istruzioni operative

Cisco

Cisco GS7000 Manuale dell'operatore

Cisco

Cisco 3600 Series Guida rapida

Cisco

Cisco MGX RPM-XF Manuale utente

Cisco

Cisco PA-4T+ Istruzioni operative e di manutenzione

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente