Cisco Beacon Point Module Manuale
REVIEW DRAFT - CISCO CONFIDENTIAL
Cisco Beacon Hardware Installation Guide
First Published: 2016-09-28
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
©2016 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
Preface v
Audience v
Conventions v
Related Documentation vi
Obtaining Documentation and Submitting a Service Request vi
CHAPTER 1
About Cisco Beacon Point Module 1
Supported Access Points 3
Cisco Beacon Point Module Features 3
Technical Specifications 3
Cisco Beacon Point Module Model Number 4
Installing a Cisco Beacon Point Module on an Access Point 4
Checking the Cisco Beacon Point Module LEDs 9
CHAPTER 2
Declarations of Conformity and Regulatory Information 11
Manufacturers Federal Communication Commission Declaration of Conformity Statement 12
VCCI Statement for Japan 13
Guidelines for Operating Cisco Virtual Beacon in Japan 13
Japanese Translation 13
English Translation 13
Canadian Compliance Statement 14
Statement 371—Power Cable and Power Injector 15
Industry Canada 15
This Device Meets FCC and International Guidelines for Exposure to Radio Waves 15
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves 16
Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences
radioélectriques 16
Cisco Beacon Hardware Installation Guide
iii
Additional Information on RF Exposure 17
Declaration of Conformity Statements 17
Cisco Beacon Hardware Installation Guide
iv
Contents
REVIEW DRAFT - CISCO CONFIDENTIAL
Preface
•Audience, page v
•Conventions, page v
•Related Documentation, page vi
•Obtaining Documentation and Submitting a Service Request, page vi
Audience
This document is for Connected Mobile Experiences (CMX) network and IT administrators who deploy Cisco
Beacon Points or Cisco Beacon Point Modules for high accuracy virtual beacon solution.
Conventions
This document uses the following conventions:
Table 1: Conventions
IndicationConvention
Commands and keywords and user-entered text appear in bold font.bold font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
italic font
Elements in square brackets are optional.[ ]
Required alternative keywords are grouped in braces and separated by vertical
bars.
{x | y | z }
Optional alternative keywords are grouped in brackets and separated by vertical
bars.
[ x | y | z ]
A nonquoted set of characters. Do not use quotation marks around the string.
Otherwise, the string will include the quotation marks.
string
Terminal sessions and information the system displays appear in courier font.courier font
Cisco Beacon Hardware Installation Guide
v
IndicationConvention
Nonprinting characters such as passwords are in angle brackets.<>
Default responses to system prompts are in square brackets.[]
An exclamation point (!) or a pound sign (#) at the beginning of a line of code
indicates a comment line.
!, #
Means reader take note. Notes contain helpful suggestions or references to material not covered in the
manual.
Note
Means the following information will help you solve a problem.Tip
Means reader be careful. In this situation, you might perform an action that could result in equipment
damage or loss of data.
Caution
Related Documentation
For more information about Cisco CMX Cloud, see:
https://support.cmxcisco.com/hc/en-us
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service
request, and gathering additional information, see What's New in Cisco Product Documentation.
To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What's
New in Cisco Product Documentation RSS feed. RSS feeds are a free service.
Cisco Beacon Hardware Installation Guide
vi
Preface
Related Documentation
REVIEW DRAFT - CISCO CONFIDENTIAL
CHAPTER 1
About Cisco Beacon Point Module
Cisco Beacon Point Module (AIR-RM-VBLE2-K9=) is a Bluetooth Low Energy (BLE version v4.2) beacon
module that is mounted on supported Access Points. The access points now act as integrated WiFI and
Bluetooth devices or Bluetooth-integrated access points. The smart device receives signals of different
strengths from multiple Bluetooth-integrated access points.
Deploying Bluetooth-integrated access points is similar to any Wi-Fi location based service solution. The
recommended density for deploying the Bluetooth-integrated access points is 1 per 2500 sq.ft. The
recommended height for a Bluetooth-integrated access points is 13 ft (3.9 m). Cisco Beacon Center requires
the correct physical orientation, position, and height of Bluetooth-integrated access points for providing
clients with indoor navigation, turn-by-turn guidance and proximity messaging for best indoor navigation
experience.
Bluetooth-integrated access pointss connect with Cisco Beacon Center over the internet using secure HTTPS
protocol. Each Bluetooth-integrated access points has a unique IP address just like any enterprise grade
networking device. Bluetooth-integrated access points should connect with Cisco Beacon Center for
Cisco Beacon Hardware Installation Guide
1
management and control. For Bluetooth-integrated access points to communicate with the Cisco Beacon
Center the port numbers 80 (TCP) and 443 (TCP, UDP) must be open.
Figure 1: Cisco Beacon Point Module (AIR-RM-VBLE2-K9=)
•Supported Access Points, page 3
•Cisco Beacon Point Module Features, page 3
•Technical Specifications, page 3
Cisco Beacon Hardware Installation Guide
2
About Cisco Beacon Point Module
REVIEW DRAFT - CISCO CONFIDENTIAL
•Cisco Beacon Point Module Model Number, page 4
•Installing a Cisco Beacon Point Module on an Access Point, page 4
•Checking the Cisco Beacon Point Module LEDs, page 9
Supported Access Points
The Cisco Beacon Point Module can be attached to the following access points:
•AP3802I
•AP3802E
Cisco Beacon Point Module Features
Cisco Beacon Point Module comes with the following features:
Table 2: Hardware Feature Summary
DescriptionFeature
A multicolor system status LED on the front-face of
the unit.
LED indicators
A recessed button that resets a Cisco Beacon Point
Module to factory settings when the
Bluetooth-integrated access points is powered up.
Reset button
Uses the power supply of the access point.Power Options
Technical Specifications
NEED IMAGE HERE
Table 3: Technical Specifications of Cisco Beacon Point Module
DescriptionFeature
275 mm x 284.7 mm x 60.5 mm
10.8 in x 11.2 in x 2.38 in
Dimensions (of access point with Cisco Beacon Point
Module)
1.38 kg (3.06 lbs)Weight
Cisco Beacon Hardware Installation Guide
3
About Cisco Beacon Point Module
Supported Access Points
REVIEW DRAFT - CISCO CONFIDENTIAL
DescriptionFeature
UL 60950-1
CAN/CSA-C22.2 No. 60950-1
FCC Part 15.247, 15.107, and 15.109
FCC Part 15 Class B
RSS-247
ICES-003 (Canada)
ClassB EMC compliance
Compliance standards
Fanless operation; passive cooling
Nonoperating (storage) temperature: -30 to 70℃(-22
to 158℉)
Operating temperature: 0 to 40℃(32 to 104℉)
Operating humidity: 10 to 90% (noncondensing)
Operating altitude: 9843 ft (3000 m)
Environmental
Less than 4.5WPower Dissipation
Cisco Beacon Point Module Model Number
Cisco Beacon Point Module is available in the following model:
Table 4: Cisco Beacon Point Module Model Number
DescriptionProduct ID
Cisco Beacon Point Module with internal antennas
that can be mounted on supported access points.
AIR-RM-VBLE2-K9=
Installing a Cisco Beacon Point Module on an Access Point
These instructions demonstrate how to install a Cisco Beacon Point Module to an access point that is already
mounted to its location using a bracket.
Cisco Beacon Hardware Installation Guide
4
About Cisco Beacon Point Module
Cisco Beacon Point Module Model Number
REVIEW DRAFT - CISCO CONFIDENTIAL
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Cisco Unità di controllo
Cisco
Cisco WS-SVC-ASA-SM1-K7 Manuale di installazione e funzionamento
Cisco
Cisco Catalyst 3110G Manuale
Cisco
Cisco HPNA Manuale utente
Cisco
Cisco ONS 15200 Manuale utente
Cisco
Cisco C3850-NM-4-1G Manuale di istruzioni
Cisco
Cisco 3110 Manuale utente
Cisco
Cisco TelePresence Touch10 Manuale utente
Cisco
Cisco 3600 Series Guida rapida
Cisco
Cisco TelePresence Touch10 Manuale utente
Cisco
Cisco GS7000 Manuale dell'operatore
Cisco
Cisco TelePresence MCU 4500 Series Manuale utente
Cisco
Cisco 6015 Manuale per l'uso e la cura
Cisco
Cisco Catalyst 9400 Series Manuale di installazione e funzionamento
Cisco
Cisco ASA5506-AP702 Manuale utente
Cisco
Cisco SCE8000 GBE Manuale utente
Cisco
Cisco MEM-CIP-64M Manuale utente
Cisco
Cisco Firepower 4110 Manuale utente
Cisco
Cisco SM-X-1T3/E3 Manuale utente
Cisco
Cisco PA-VXA Series Istruzioni operative e di manutenzione
Cisco
Cisco TelePresence MCU 4200 Series Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
