Cisco WS-SVC-WISM2-1-K9 Guida rapida

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Catalyst 6500 Series Wireless Services Module 2

Installation and Verification Note

Product numbers: WS-SVC-WISM2-1-K9, WS-SVC-WISM2-3-K9, WS-SVC-WISM2-5-K9

This document provides installation procedures for the Catalyst 6500 Series Wireless Services Module

2 (WiSM2) and contains these sections:

•Front Panel Description, page 1

•Power Requirements, page 8

•System Requirements, page 8

•Safety Overview, page 8

•Preparing to Install the WiSM2, page 9

•Required Tools, page 9

•Installing the WiSM2, page 10

•Verifying the Installation, page 14

•Removing the WiSM2, page 14

•Related Documentation, page 16

•Obtaining Documentation and Submitting a Service Request, page 16

Front Panel Description

The WiSM2 front panel (Figure 1) includes six status light-emitting diodes (LEDs), USB and RJ-45

console ports, and USB ports.

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Figure 1 WiSM2 Front Panel

These sections describe the WiSM2 front panel:

•Status LEDs, page 3

•CONSOLE Ports, page 5

•USB Ports, page 7

282219

CLEI

CONSOLE

POWR SYSTEM ALARM

CISCO WIRELESS SERVICE MODULE (WISM2)

WS-SVC-WISM2

POWER

LED

ALARM

LED

USB

CONSOLE

LED

USB

LED

USB

Ports

SYSTEM

LED

RJ-45

CONSOLE

LED

USB

CONSOLE

Port

RJ-45

CONSOLE

Port

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Status LEDs

Six status LEDs indicate the operating states of the WiSM2 module. Table 1 describes the status LED

operation.

Table 1 Status LED Descriptions

LED Label Color Description

SYSTEM Green/Amber System Status:

•During system power-up:

–

SYSTEM blinks amber.

–

ALARM is continuous amber.

•During system boot:

–

SYSTEM blinks green.

–

ALARM is continuous amber.

•After bootup:

–

SYSTEM is continuous green.

–

ALARM is off.

•During controller image upgrade:

–

SYSTEM is continuous green.

–

ALARM blinks green.

•System crash:

–

SYSTEM is continuous amber.

–

ALARM is off.

•Firmware Error:

–

SYSTEM is continuous amber.

–

ALARM is continuous amber.

Note Power cycle the controller to clear the

firmware error.

•Internal Voltage Error:

–

SYSTEM blinks amber.

–

ALARM is continuous amber.

•Temperature Error:

–

SYSTEM is off.

–

ALARM blinks amber.

Note Check for blocked air vents and fans on the

chassis.

ALARM

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

OIR LED Descriptions

There is a consistent CLI-based Online Insertion and Removal (OIR) notification scheme for all slots

that support “Nonsurprise” OIR. Table 2 describes the OIR LED indicator for these slots. There is no

special LED indication for module insertion. The PSU and Fan Tray supports surprise OIR and does not

have a special CLI or LED indication.

POWER Green The POWER LED is green when the module is receiving power

and is off when power is removed.

CONSOLE

USB CONSOLE

LED

RJ-45 CONSOLE

LED

Green USB console port LED status:

•Off—Not active.

•Solid green—Indicates the active aux port.

Note When this LED is on, the RJ-45 console

port LED is off.

Green RJ-45 console port LED status:

•Off—Not active.

•Solid green—Indicates the active console port.

Note When this LED is on, the USB console

(aux) port LED is off.

USB LED

(USB 0 and 1)

Green/Amber USB 0/USB 1 OIR indication/notification:

•Off—Not active

•Solid green—Active and enabled.

•Solid amber—Active with failure.

Note For LED descriptions, see the “OIR LED Descriptions”

section on page 4.

Table 1 Status LED Descriptions (Continued)

LED Label Color Description

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Table 2 OIR LED Descriptions

CONSOLE Ports

There are two types of CONSOLE ports, the RJ-45 console port and the USB console port. See Figure 2

for the location of the CONSOLE ports.

Note On the front panel of the WiSM2, both ports have one CONSOLE label.

The WiSM2 offers both an RJ-45 serial console interface and a USB console interface. Only one of the

console ports can be active at a time; the USB console takes priority over the RJ-45 console by default.

When a USB Host (PC) is plugged into the USB console port, the hardware automatically switches over

to use the USB console. When the USB cable is removed or the PC deactivates the USB connection, the

hardware automatically switches to the RJ-45 console interface.

Note Only a PC that has the necessary USB console device driver causes the USB console to become active.

Plugging in a PC that does not have the USB console driver support does not cause a switchover.

When using the USB console port for operation with Microsoft Windows, you must install the Cisco

Windows USB Console Driver on any PC that is connected to the console port. If it is not installed,

prompts guide you through a simple installation process. To download the latest Cisco Windows USB

Console Driver, follow these steps:

Step 1 Go to the Software download page at

http://www.cisco.com/cisco/software/navigator.html

Step 2 Click Wireless.

Step 3 Click Wireless LAN Controllers.

Step 4 Click Integrated Controllers and Controller Modules.

Step 5 Click Cisco Wireless Services Module 2 (WiSM2).

Step 6 Click USB Console Software and follow the download instructions.

LED Label Color Description

USB Green/Yellow Off—Not active

Green—Active and enabled

Blinking green and turns off—Module is ready for removal

Note The software behavior will be

un-defined if the module is removed

before the LED is turned off.

Yellow: Present with failure

USB0

USB1

Green/Yellow

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Note The USB console driver also works on Linux and MacOS Hosts. See the notes listed inside the

Cisco Windows USB Console driver package for installation details.

There is an LED adjacent to the USB CONSOLE connector and an LED next to the RJ-45 CONSOLE

connector. One of these two LEDs will light to indicate the active console. For LED information see the

“Status LEDs” section on page 3. Both ports are described in this section.

Figure 2 USB CONSOLE Port and RJ-45 CONSOLE Port

RJ-45 CONSOLE Port

The RJ-45 CONSOLE port is used for the initial configuration of the WiSM2. The port is a single RS232

port used for customer console port access and is connected to the control plane UART serial interface.

The console port pinouts on the RJ-45 connector, is shown in Table 3. At initial power-up, the software

should set the default baud rate to 9600.

Table 3 Console RJ-45 Port Pinouts

CLEI

CONSOLE

282220

USB

CONSOLE

Port

RJ-45

CONSOLE

Port

Pin Number

Console/Aux Port (RJ-45)

Signal Direction

1NC

2TXD-DBG Output

3TXD Output

4GND

5GND

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Note The initial WiSM2 configuration must be made through a direct connection to the RJ-45 CONSOLE

port. After the initial configurations, you can make an Secure Shell (SSH) or Telnet connection to the

module to further configure the module.

USB Console Port

The USB Console port is a Type B interface that allows an interface to the console from a PC using a

Type A to Type B cable. The connector is a mini Type B. The Type B connector supports a USB interface

and outputs a standard serial (RS232) stream between the RJ-45 console stream and the USB Console

stream. Only one USB Console port is active at a time, either the RJ-45 or USB. The controller detects

if a connection is made to the USB-Console and deactivates the RJ-45 console. The pinouts of the mini

Type B is shown in Table 4.

Table 4 USB CONSOLE Type B Port Pinouts

Note In this document, the term “Mini Type B” is used to indicate only a 5-Pin Mini Type B connector and

cable. There is a 4 Pin Mini Type B connector (and cable) as well, but the two are not compatible.

USB Ports

There are two Type-A external USB ports. Each port is fully complaint per the USB 2.0 specification,

and support low (1 Mb/s), full (12 Mb/s), and high speed (480 Mb/s) operation. As per the USB 2.0

specification, these ports are backwards compatible with USB1.1 devices.

The dual-port USB receptacle is shielded and the shield is tied to chassis ground. The Type-A receptacle

can only accept Type-A plugs. Mini-A and Mini-AB plugs are not supported. The Type A connector

pinouts are shown in Table 5.

6RXD Input

7 RXD-DBG Input

8NC

Pin Number

Console/Aux Port (RJ-45)

Signal Direction

Pin Number Description

1+5V

2D-

3D+

4NC

5GND

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Table 5 USB Ports Type A Connector Pinouts

Power Requirements

The WiSM2 requires 225 W for operation. Make sure that your chassis can provide this power.

Note All Catalyst 6500 chassis (except the Catalyst 6503) require the fan tray 2 module, which requires the

2500 W power supply for proper operation. For planning purposes, be aware that the 2500 W power

supply requires a 20 A input power circuit with a NEMA plug.

You can use the show power command to view power details for your installation, including the system

power available and power statistics for installed power supplies and cards.

System Requirements

Before you install the WiSM2 into the Catalyst 6500 series switch, see the Release Notes for Catalyst

6500 Series Wireless LAN Services Module Software Release to make sure that the switch meets the

hardware and software requirements.

Safety Overview

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may

harm you. A warning symbol precedes each warning statement.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Pin Number Description

1+5V

2D-

3D+

4GND

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Warning

Hazardous voltage or energy is present on the backplane when the system is operating. Use caution

when servicing.

Statement 1034

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement

1029

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Preparing to Install the WiSM2

Note Before installing the WiSM2, you must install the Catalyst 6500 series switch chassis and at least one

supervisor engine. For information on installing the switch chassis, see the Catalyst 6500 Series Switch

Installation Guide.

Before installing the WiSM2, make sure that the following items are available:

•Catalyst 6500 series switch chassis

•Management station that is available through a console connection to perform configuration tasks

Required Tools

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

These tools are required to install the WiSM2 into the Catalyst 6500 series switch:

•Flat-blade screwdriver

•Wrist strap or other grounding device

•Antistatic mat or antistatic foam

Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note

78-16318-01

Installing the WiSM2

Note Before installing the WiSM2, you must install the Catalyst 6500 series switch chassis and at least one

supervisor engine. For information on installing the switch chassis, see the Catalyst 6500 Series Switch

Installation Guide.

This section describes how to install the WiSM2 into the Catalyst 6500 series switch.

Note All modules, including the supervisor engine (if you have redundant supervisor engines), support hot

swapping. You can add, replace, or remove modules without interrupting the system power or causing

other software or interfaces to shut down. For more information about hot-swapping modules, see the

Catalyst 6500 Series Switch Module Installation Guide.

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself.

Statement 94

To install the WiSM2 into the Catalyst 6500 series switch, follow these steps:

Step 1 Make sure that you take the necessary precautions to prevent ESD damage.

Step 2 Choose a slot for the WiSM2. See Figure 3 for the slot numbers on a Catalyst 6500 series switch.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Unità di controllo

Cisco

Cisco TelePresence Touch10 Manuale utente

Cisco

Cisco T1 Manuale utente

Cisco

Cisco Catalyst 3110G Manuale

Cisco

Cisco MEM-NP8F Series Guida rapida

Cisco

Cisco PA-VXA Series Istruzioni operative e di manutenzione

Cisco

Cisco CSS 11500 Manuale di servizio

Cisco

Cisco T3 Guida rapida

Cisco

Cisco NCS 1010 Foglio di istruzioni

Cisco

Cisco Firepower 4112 Manuale

Cisco

Cisco NCS 1004 Manuale utente

Cisco

Cisco ONS 15540 ESPx Manuale di istruzioni

Cisco

Cisco 3600 Series Guida rapida

Cisco

Cisco Catalyst 9400 Series Manuale di installazione e funzionamento

Cisco

Cisco Catalyst 5000 Series Manuale utente

Cisco

Cisco GS7000 Istruzioni operative

Cisco

Cisco SCE8000 GBE Manuale utente

Cisco

Cisco ATUC-4DMT-ISDN Istruzioni operative e di manutenzione

Cisco

Cisco NM-1CT1 Guida rapida

Cisco

Cisco MGX RPM-XF Manuale utente

Cisco

Cisco Beacon Point Module Manuale

Cisco

Cisco SM-X-1T3/E3 Manuale utente

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuale di installazione e funzionamento

Cisco

Cisco C3850-NM-4-1G Manuale di istruzioni

Cisco

Cisco 3110 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente