Cisco FlexWAN Manuale utente

CHAPTER

1-1

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Installing the FlexWAN and Enhanced FlexWAN

Modules

This chapter contains the following sections:

•Preparing to Install the FlexWAN or Enhanced FlexWAN Module, page 1-1

•Installing the FlexWAN and Enhanced FlexWAN Modules, page 1-3

•Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter, page 1-6

Preparing to Install the FlexWAN or Enhanced FlexWAN

Module

Note Before you can install the FlexWAN or Enhanced FlexWAN modules, you must install at least one

supervisor engine in the chassis. Throughout this publication, the term supervisor engine refers to

Supervisor 720 Engine.

The following tools adn equipment are required to install the FlexWAN and Enhanced FlexWAN

modules:

•3/16-inch flat-blade screwdriver for the captive installation screws on the FlexWAN and Enhanced

FlexWAN modules.

•Antistatic mat or antistatic foam.

•Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist

strap included with all upgrade kits, field-replaceable units (FRUs), and spares.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are

improperly handled, results in complete or intermittent failures. Port adapters and processor

modules consist of printed circuit boards that are fixed in metal carriers. Electromagnetic

interference (EMI) shielding and connectors are integral components of the carrier. Although the

metal carrier helps to protect the board from ESD, use a preventive antistatic strap during handling.

1-2

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Preparing to Install the FlexWAN or Enhanced FlexWAN Module

Follow these guidelines for preventing ESD damage:

•Always use an ESD wrist or ankle strap, and ensure that it makes maximum contact with the skin.

Make sure that the wrist or ankle strap is in contact with bare skin.

•Avoid contact between the printed circuit boards and clothing. The wrist strap only protects

components from ESD voltages on the body; ESD voltages on clothing can still cause damage.

•The disposable ESD grounding strap supplied with field replaceable units (FRUs) has a metal clip

at one end. Attach the metal clip (equipment end of the strap) to an unfinished (bare metal) chassis

surface.

•The Catalyst 7600 series chassis also has a built-in ESD grounding connector. This is a banana plug

connector and is identified by the ground symbol next to the connector. See Figure 1-1 for an

example of a chassis ESD wrist strap connection.

•When installing a component, use any available ejector levers or captive installation screws to

properly seat the bus connectors in the backplane or midplane. These devices prevent accidental

removal, provide proper grounding for the system, and help to ensure that bus connectors are

properly seated.

•When removing a component, use any available ejector levers or captive installation screws to

release the bus connectors from the backplane or midplane.

•Handle carriers by available handles or edges only; avoid touching the printed circuit boards or

connectors.

•Place a removed component board-side-up on an antistatic surface or in a static shielding container.

If you plan to return the component to the factory, immediately place it in a static shielding

container.

•Never attempt to remove the printed circuit board from the metal carrier.

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be

between 1 and 10 megohms (Mohm).

Figure 1-1 Example of Chassis ESD Wrist Strap Ground

113742

PS1

PS2

FAN

LINK

SLOT 2

SLOT 1

PCMCIA

EJECT AUX

CONSOLE

Enet

RESET

SWITCH/PROCESSOR

UTP3

UTP

UTP3

UTP

ESD wrist strap

ESD ground strap

connector

1-3

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing the FlexWAN and Enhanced FlexWAN Modules

Warning

Only trained and qualified personnel should be allowed to install or replace this equipment.

In the procedure that follows, the FlexWAN and Enhanced FlexWAN modules are installed into the

horizontal slots of a Cisco 7613 router chassis. (see Figure 1-2).

Note The FlexWAN and Enhanced FlexWAN modules are not supported without port adapters. You must

install at least one port adapter before installing the module in the chassis.

Figure 1-2 Slots on the Cisco 7613 Router

To install the FlexWAN or Enhanced FlexWAN modules, follow these steps:

Step 1 Make sure that you take the necessary precautions to prevent ESD damage.

Caution Handle modules by the carrier edges only. Always use an ESD wrist strap when handling modules or

coming into contact with internal components.

INPUT

FAN

OUTPUT

FAIL

INPUT

FAN

OUTPUT

FAIL

96930

Power supply 1 Power supply 2

(redundant)

ESD ground strap

connection

FAN

STATUS

SUPERVISOR2

WS-X6K-SUP2-2GE

STATUS

SYSTEM

CONSOLE

PWRMGMT

RESET

CONSOLE

PORT

MODE PCMCIA EJECT

PORT1 PORT2

Switch Load

100%

LINK

SUPERVISOR2

WS-X6K-SUP2-2GE

STATUS

SYSTEM

CONSOLE

PWRMGMT

RESET

CONSOLE

PORT

MODE PCMCIA EJECT

PORT1 PORT2

Switch Load

100%

LINK

Fan assembly

hanced FlexWAN module

Optical Service Modules

Supervisor engine

Redundant supervisor

engine

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

OC12POSMM

OSM-40C12-POS-MM

STATUS1

RESET

LINK

CARRIER

ALARM

ACTIVE

PORT1

CARRIER

ALARM

ACTIVE

PORT2

CARRIER

ALARM

ACTIVE

PORT3

CARRIER

ALARM

ACTIVE

SWITCHFABRICMDL

STATUS

SELECT

ACTIVE

SWITCHFABRICMDL

STATUS

SELECT

WS-C6500-SFM

ACTIVE

STATUS

1-4

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing the FlexWAN and Enhanced FlexWAN Modules

Step 2 Install port adapters on the FlexWAN or Enhanced FlexWAN module (see the “Installing a FlexWAN or

Enhanced FlexWAN Module Port Adapter” section on page 1-6). Tighten any screws provided to secure

the port adapter.

Step 3 Choose a slot for the FlexWAN or Enhanced FlexWAN module.

Step 4 Use a screwdriver to loosen the captive installation screws that secure the switching-module filler plate

(or the existing switching module) from the desired slot, if present.

Step 5 Remove the switching-module filler plate (or the existing switching module), if present.

Step 6 Hold the module handle with one hand, and place your other hand under the carrier to support the

module. Do not touch the printed circuit boards or connector pins.

Step 7 Place the module in the slot. Align the notch on the sides of the module carrier with the groove in the slot.

Step 8 Keep the modules at a 90-degree orientation to the backplane, and carefully slide the module into the

slot until the module faceplate contacts the ejector levers (see Figure 1-3).

Figure 1-3 Ejector Levers and Captive Installation Screws

Step 9 Use the thumb and forefinger of each hand and simultaneously push in the left and right levers to fully

seat the module in the backplane connector.

Caution Always use the ejector levers when installing or removing modules. A module that is partially seated in

the backplane causes the system to halt and subsequently crash.

Step 10 Tighten the captive installation screws on the left and right ends of the module.

Step 11 Enter the show module command to verify that the system acknowledges the new module and has

brought it online.

The following example shows the output of the show module command:

STATUS

32465

Captive

installation

screws

Ejector lever

1-5

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing the FlexWAN and Enhanced FlexWAN Modules

Router# show module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD0719027M

6 0 2 port adapter Enhanced FlexWAN WS-X6582-2PA SAD073103PD

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

5 000c.ce63.e290 to 000c.ce63.e293 2.1 7.7(1) 12.2(TETONS_ Ok

6 00e0.aabb.cc00 to 00e0.aabb.cc3f 1.x 12.2(TETONS_ 12.2(TETONS_ Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- ------------------ ------------ ------- -------

5 Policy Feature Card 3 WS-F6K-PFC3A SAD072000G6 1.1 Ok

5 MSFC3 Daughterboard WS-SUP720 SAD072001YS 1.2 Ok

Mod Online Diag Status

--- -------------------

5 Pass

6 Pass

--------------------------------------------------------------------------------

Note The status field in the output of the show module command indicates by “Ok” that the module is

operational.

The show module command displays “Ok” status and “Mod Online Diag Status” only after the

FlexWAN or Enhanced FlexWAN module has booted completely. While the FlexWAN or Enhanced

FlexWAN module is booting (the STATUS LED is orange or red), the “Ok” status and the “Mod Online

Diag Status” is unknown.

Step 12 After you install the FlexWAN or Enhanced FlexWAN modules, you must connect the port adapter

cables and configure the port adapter interfaces.

For complete cabling and configuration information for the port adapters, refer to the documentation that

shipped with your port adapter.

1-6

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Installing a FlexWAN or Enhanced FlexWAN Module Port

Adapter

This section describes how to install a port adapter in the FlexWAN or Enhanced FlexWAN module in the

Catalyst 6500 series switches or Cisco 7600 series routers.

You can install port adapters in either port adapter bay 0 or port adapter bay 1. Figure 1-4 shows one

PA-H port adapter installed in port adapter bay 0 on a FlexWAN or Enhanced FlexWAN module.

Figure 1-4 Port Adapter Installed in Bay 0

Required Tools and Equipment

You need the following tools and equipment to install a port adapter. If you need additional equipment,

contact a service representative for ordering information.

•Any specific cables for your port adapter

•Number 2 Phillips screwdriver

•Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist

strap included with all upgrade kits, field-replaceable units (FRUs), and spares

•Antistatic mat

•Antistatic container

29845

STATUS

ENABLED

HSSI

Rev. B

LB/C

Port adapter

blank in bay 1

Port adapter

securing screw

Port adapter handles not shown

Port adapter

in bay 0

1-7

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Handling Port Adapters

Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge

(ESD) damage.

Caution Always handle the port adapter by the carrier edges and handle. Never touch the port adapter’s

components or connector pins.

Figure 1-5 Handling a Port Adapter

Caution To prevent system problems, do not remove port adapters from the FlexWAN or Enhanced FlexWAN

modules or attempt to install other port adapters on the modules when the module is operating.

Replacing Port Adapters

Although the FlexWAN or Enhanced FlexWAN module supports online insertion and removal,

individual port adapters do not. To replace port adapters, you must first remove the module from the

chassis, and then install or replace the port adapters as required.

When a Port Adapter Is Not in Use

When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allow the router or

switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper

airflow across the port adapters.

If there is a blank port adapter on the FlexWAN or Enhanced FlexWAN module in which you want to

install a new port adapter, you must first remove the module from the chassis, and then remove the blank

port adapter.

H6420

Metal carrier

Printed circuit board

1-8

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Installing a New Port Adapter in an Enhanced FlexWAN Module

This section describes how to first remove a port adapter from an Enhanced FlexWAN module, then how

to install a new port adapter into its bay. (The procedure for the FlexWAN module is similar.)

Note: You must first remove the

Enhanced FlexWAN Module from

the chassis before removing a port

adapter from the Enhanced

FlexWAN Module.

Step 2

With the screw removed, grasp the

handle on the front of the

port adapter (or blank port adapter)

and carefully pull it out of its bay,

away from the edge connector at

the rear of the bay. (See A.)

Step 3

To install the port adapter, carefully

align the port adapter carrier

between the upper and the lower

edges of the port adapter bay.

(See B.)

Step 5

Install the screw in the rear of the

port adapter bay. Do not overtighten

the screw. (See A.)

Step 6

Reinstall the Enhanced FlexWAN

Module in the chassis, and tighten

the captive installation screw on each

side of the Enhanced FlexWAN

Module faceplate. (See C.)

96929

Step 1

To remove the port adapter,

remove the screw that

secures the port adapter (or

blank port adapter). (See A.)

Step 4

Carefully slide the new

port adapter into the port adapter

bay until the connector on the

port adapter is completely seated in

the connector at the rear of the

port adapter slot. (See B.)

Slot

guide

Screw

FAN

LED

SUPERVISOR I

STATUS

SYSTEM

ACTIVE

PWR MGMT

RESET

CONSOLE1%PCMCIAEJECT

LINK

SUPERVISOR I

WS-X6K-SUP1

STATUS

SYSTEM

ACTIVE

PWR MGMT

RESET

CONSOLE

SwitchLoad

100%

DTE/

DCE

PCMCIAEJECT

PORT1

LINK

PORT2

LINK

8PORTGIGABITETHERNET

WS-X6408

LINK

STATUS

2345678

LINK

8PORTGIGABIT ETHERNET

WS-X6408

LINK

STATUS

2345678

LINK

8PORTGIGABITETHERNET

WS-X6408

LINK

STATUS

2345678

LINK

24PORT100FX

WS-X6224

STATUS

24PORT100FX

WS-X6224

STATUS

24PORT100FX

WS-X6224

STATUS

LINK

STATUS

1-9

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Warnings and Cautions

Observe the following warnings and cautions when installing or removing port adapters.

Caution Do not slide a port adapter all the way into the slot until you have connected all the required cables.

Caution To prevent jamming the carrier between the upper and the lower edges of the port adapter slot, and to

ensure that the edge connector at the rear of the port adapter mates with the connection at the rear of the

port adapter slot, make certain that the carrier is positioned correctly.

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself.

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Warning

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.

Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The

telecommunications lines must be disconnected 1) before unplugging the main power connector or

2) while the housing is open, or both.

1-10

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1 Installing the FlexWAN and Enhanced FlexWAN Modules

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Unità di controllo

Cisco

Cisco C3850-NM-4-1G Manuale di istruzioni

Cisco

Cisco GS7000 Istruzioni operative

Cisco

Cisco NM-1CT1 Guida rapida

Cisco

Cisco WS-G5484 Manuale utente

Cisco

Cisco NCS 1004 Manuale utente

Cisco

Cisco Catalyst 3110G Manuale

Cisco

Cisco PA-VXA Series Istruzioni operative e di manutenzione

Cisco

Cisco 6015 Manuale per l'uso e la cura

Cisco

Cisco TelePresence Touch10 Manuale utente

Cisco

Cisco TelePresence MCU 4200 Series Manuale utente

Cisco

Cisco ATUC-4DMT-ISDN Istruzioni operative e di manutenzione

Cisco

Cisco TelePresence Touch10 Manuale utente

Cisco

Cisco Firepower 4112 Manuale

Cisco

Cisco Catalyst 5000 Series Manuale utente

Cisco

Cisco CSS 11500 Manuale di servizio

Cisco

Cisco PA-4T+ Istruzioni operative e di manutenzione

Cisco

Cisco CGM-WPAN-OFDM-FCC Manuale utente

Cisco

Cisco Catalyst WS-X3001 Manuale dell'operatore

Cisco

Cisco T1 Manuale utente

Cisco

Cisco MEM-CIP-64M Manuale utente

Cisco

Cisco NM-1E2W Guida rapida

Cisco

Cisco SM-X-1T3/E3 Manuale utente

Cisco

Cisco WS-SVC-ASA-SM1-K7 Manuale di installazione e funzionamento

Cisco

Cisco Firepower 4110 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente