Cisco FirePOWER 8000 Series Manuale utente

Insert and Remove a Network Module (NetMod) on

an 8000 Series FirePOWER Appliance

Document ID: 118194

Contributed by Nazmul Rajib and Josiah Zimmermann, Cisco TAC

Engineers.

Aug 06, 2014

Contents

Introduction

Prerequisites

Before You Begin

Required Tool and Hardware

Remove the Module or Slot Cover

Insert a Module or Slot Cover

Introduction

Instead of the usual fixed port configuration of most high−end security appliances, the modularity of the 8000

Series appliances enables you to choose and change the number and type of interfaces for the appliance.

Various Network Modules (NetMods) are inserted into the 8000 Series appliances to customize the interface

configuration to match your network requirements. This document describes how to insert and remove a

NetMod in an 8000 series FirePOWER appliance.

Caution: If you install a NetMod in an incompatible slot on your appliance or a NetMod is otherwise

incompatible with your system, an error or warning message appears in the web interface on the managing

Defense Center when you attempt to configure the NetMod.

Prerequisites

Before You Begin

Before you begin, prepare to insert or remove your module using the following guidelines:

Identify all appliance and module parts.• Identify the slots where you want to install your NetMods.• Identify the correct slots for your stacking modules.• Confirm that the EMI gaskets are in place.• Unplug all power cords from the appliance.•

Warning: You cannot hot−swap modules. You must power down and unplug both power cords from the

appliance before inserting or removing modules.

Caution: Use proper electrostatic discharge (ESD) practices such as wearing wrist straps and using an ESD

work surface when handling the modules. Store unused modules in an ESD bag or box to prevent damage.

Required Tool and Hardware

T8 Torx screwdriver• 8000 Series FirePOWER appliance•

Remove the Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to release the latch.

Step 3: Slide the module out of the slot.

Insert a Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to open the latch. The near end of the latch is visible. The far

end of the latch is inside the module.

Step 3: Insert the module into the slot until the far end of the latch is inside the slot and the near end of the

latch touches the outside of the slot.

Step 4: Push the lever toward the module so that the latch engages and pulls the module into the slot.

Step 5: Press firmly on the screw hole to push the lever fully against the module to secure the latch.

Step 6: Insert and tighten the reserved T8 Torx screw into the lever.

Updated: Aug 06, 2014 Document ID: 118194

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco ONS 15310-MA SDH Manuale

Cisco

Cisco IAD1101 Manuale utente

Cisco

Cisco WS-CE500 - Catalyst Express 500-24PC Manuale di istruzioni

Cisco

Cisco IPS 7.1 Manuale utente

Cisco

Cisco CPS-MSP-1RU-K9 Manuale utente

Cisco

Cisco GS7000 Istruzioni operative

Cisco

Cisco 3600 Series Istruzioni operative e di sicurezza

Cisco

Cisco ISA 3000 Guida rapida

Cisco

Cisco IronPort C670 Manuale utente

Cisco

Cisco OSM-12CT3/T1 - Optical Services Module... Guida rapida

Cisco

Cisco Edge 300 Series Guida rapida

Cisco

Cisco ONS 15454 Manuale di istruzioni

Cisco

Cisco Nexus 93600CD-GX Manuale

Cisco

Cisco Linksys NSLU2 Manuale utente

Cisco

Cisco Firepower 2130 Guida alla manutenzione e all'assistenza

Cisco

Cisco IAD2430 Series Manuale

Cisco

Cisco MA-UMNT-MR-A3 Manuale utente

Cisco

Cisco Aironet 1000 Series Manuale

Cisco

Cisco CGR 1240 Manuale utente

Cisco

Cisco Mc3810 - 16MB Flash Memory Guida rapida

Cisco

Cisco WAE-674-K9 - Wide Area Application Engine... Manuale

Cisco

Cisco ONS 15310-MA Manuale utente

Cisco

Cisco NSS4100 - Gigabit Storage System Manuale di istruzioni

Cisco

Cisco 2610 - Router - EN Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente