Cisco Wap581 Manuale utente

Quick Start Guide

Cisco WAP581 Wireless-AC/N Dual Radio

Access Point with 2.5GbE LAN

Welcome

Thank you for choosing the Cisco WAP581 Wireless-AC/N Dual Radio Wave 2 Access

Point with 2.5GbE LAN. The Cisco WAP581 is an indoor dual radio 802.11acWave2 +

802.11acWave1 access point with Power over Ethernet (PoE). -PoE Supplied by UL

Listed I.T.E.

NOTE The unit should be connected to PoE networks only, without routing to the

outside plant.

This guide is designed to familiarize you with the general layout of the access point,

describe how to deploy the device in your network, and describe how to configure

the device. Your access point has more features and functionality than what is

described in this guide. For additional information, see the Administration Guide. A

Cisco WAP125 Quick Start Guide 2

link to the Administration Guide is found in To reset the device to factory default

settings:, page11.

Package Contents

•Wireless Access Point

•Mounting kit

•This Quick Start Guide

•Ethernet cable

•Pointer Card with China RoHS

•Technical Support Contacts

•EU Directives 1999/5/EC Compliance Information (for EU SKU only)

1Before You Begin

Before you begin the installation, make sure that you have the following equipment

and services:

•A computer with one of the following browser support:

–Internet Explorer 9.0 or later

–A recent version of either Chrome, Firefox or Safari

•Tools for installing the hardware

•One or more Ethernet network switches with either PoE, PoE injector or

external power adapter

2Cisco WAP581 Wireless-AC/N Premium Dual

Radio Access Point with PoE Setup Features

Front Panel

The front panel of the device consists of a single system LED. For a full description

of the colors of the light and its indications, see Verifying the Hardware

Installation, page 6.

Back Panel

The back panel of the device has two RJ-45 Ethernet ports. Facing the back of the

device, the right port (labeled “ETH0/PD”) is an 2.5GbE with 802.3at & 802.3af

Cisco WAP125 Quick Start Guide 3

Power over Ethernet (PoE) port which is used to power your device. The left port

(labeled “ETH1”) is a general Gigabit Ethernet LAN interface. Both are auto-sensing,

Gigabit Ethernet (802.3) ports used to connect your WAP devices to network devices,

such as computers, routers, or switches. We strongly recommend that you use a

Category 5e or better cable for Gigabit connectivity.

Side Panel

The side panel of the device consists of the following:

•Kensington Lock Slot—Helps to secure the unit physically using a cable

attached to the device.

•Reset button—See Rebooting the Devices or Returning them to their Factory

Default Settings, page10 for information on the Reset button.

Default Setting

Parameter

Default Value

Username

cisco

Password

cisco

LAN IP Address

DHCP address assigned by

server

Fallback LAN IP

192.168.1.245

Subnetwork Mask

255.255.255.0

If you are using a Cisco RV Series router, the default range for the DHCP assigned

address is from 192.168.1.100 to 192.168.1.254. Any device connecting to the same

LAN will be assigned an IP address in this range.

If your network does not have an existing DHCP server, the WAP581 will start a

DHCP server for WLAN stations and stop the DHCP client when WAP581 is in factory

default. The DHCP server will assign the IP address from 192.168.1.20 to

192.168.1.100.

3Mounting the Cisco WAP581 Wireless-AC/ N

Premium Dual Radio Access Point with PoE Setup

You can place your access point on a desktop, or mount it on a wall or ceiling.

Cisco WAP125 Quick Start Guide 4

Placement Tips

•Ambient Temperature—To prevent the access point from overheating, do not

operate it in an area that exceeds an ambient temperature of 104°F (40°C).

•Mechanical Loading—The device should be level, stable, and secure to

prevent it from sliding or shifting out of position.

Wall and Ceiling Mounting

The Cisco WAP581 can be wall or ceiling-mounted. There is a mounting kit packed

with your device. The kit is designed to install your device to the wall or the ceiling.

The mounting bracket has some flexibility so that you can reuse existing holes

drilled for a Cisco WAP551 or WAP561 device. The installer can remove the Cisco

WAP551 or WAP561 and mount the Cisco WAP581. You will need 4pcs of anchors

and screws to mount the device. The dimensions for the mount kit screws are as

follows

1 7.8 to 8.3 mm/ 2 21.8 to 22.3 mm/ 3 5.5 to 6.0 mm/ 4 17.5 to 18.2mm/ .31 to .33

in .86 to .88 in .22 to .24 in .69 to .72 in

The details to mount the Cisco WAP581 on a hard ceiling or wall is depicted in the

following diagram

Cisco WAP125 Quick Start Guide 5

WARNING Insecure mounting might damage the device or cause injury. Cisco is not

responsible for damages incurred by insecure wall or ceiling mounting.

STEP 1 Determine where you want to mount the device. Verify that the surface is

smooth, flat, dry, and sturdy.

STEP 2 Drill two pilot holes into the surface 2.75 inches (70 mm) apart for your Cisco

WAP device.

STEP 3 Insert a screw into each hole, leaving a gap between the surface and the base

of the screw head.

STEP 4 Place the upper slots of the bracket over the screws, adjust the screws

accordingly, and slide the bracket down until the screws fit snugly into the

slots.

STEP 5 Using the bracket as a template, drill two more holes for the lower screws.

STEP 6 Insert a screw into each lower hole.

Cisco WAP125 Quick Start Guide 6

STEP 7 Slide the WAP device into the bracket, placing the cable through the break-out

tab found in the back of the bracket.

4Connecting the Cisco WAP581 WirelessAC/N

Premium Dual Radio Access Point with PoE Setup

The WiFi default SSID is “Cisco SB-Setup” with the passphrase “cisco123” in WPA2-

PSK AES. This wireless default configuration will not allow traffic between WiFi and

Ethernet; users will need to go through the setup wizard to resume the traffic

between WiFi and Ethernet.

The user can also perform the initial configuration using a wired Ethernet

connection.

To connect the device to the wired network:

STEP 1 Connect the Ethernet cable to the Ethernet port of a PoE switch.

STEP 2 Connect the other end of the network Ethernet cable to the Ethernet port

(PoE) of the wireless access point.

NOTE WAP581 bundles the two Ethernet ports to be link aggregation mode.

If the two Ethernet ports have been connected at the same time, the link

partner must also support link aggregation.

After installation, all lights should be active. Refer to Verifying the

Hardware Installation, page 6 for details about the different lights on each switch.

5Verifying the Hardware Installation

To verify the hardware installation, complete the following tasks:

•Check the cable connections.

•Check the state of the indicator lights

Label

Activity

Description

Power

Off

The WAP581 is out of power.

Cisco WAP125 Quick Start Guide 7

Solid (Green)

The Cisco WAP581 is normal; no wireless client

connected.

Flashing (Green)

The device is booting.

Solid (Blue)

The Cisco WAP581 is normal; at least one

wireless client connected.

Flashing (Blue)

The Cisco WAP581 is upgrading the firmware.

Solid (Red)

The Cisco WAP581 fails to boot with both

firmware images.

Flashing cycle

with Green and

Blue

Indicates the availability of new firmware

updates for the hardware that can be

downloaded from Cisco.com

Ethernet: Left-

Green

Off

No Ethernet link.

Solid Green

Ethernet link is active.

Flashing Green

Transmitting or receiving data.

Ethernet No.0:

Right-Green

Off

Gigabit Ethernet Link is active

Solid Green

2.5Gigabit Ethernet Link is active

Ethernet No.1:

Right-Green

Off

Fast Ethernet Link is active

Solid Green

Gigabit Ethernet Link is active

NOTE If you need help resolving a problem, visit the Cisco Support Community at

www.cisco.com/go/smallbizsupport.

6Getting Started with the Configuration

To configure the wireless access points, you can either use Ethernet or wireless.

Please follow these steps to access the Wizard and then the web-based

configuration utility from your computer by Ethernet:

STEP 1 Ethernet: Connect the wireless access point to the same network (IP subnet)

as your computer. The factory default IP address configuration of the

access points is DHCP. Make sure your DHCP server is running and can be

reached.

See Incorrect IP Address, page10 for troubleshooting information, or if

you do not have a DHCP server.

Wireless: Search the wireless SSID "CiscoSB-Setup", and connect to this

SSID with the passphrase "cisco123".

STEP 2 Locate the IP address of the wireless access point.

Cisco WAP125 Quick Start Guide 8

a. The wireless access points can be accessed and managed by

Cisco network tools and services including the Cisco FindIT Network

Discovery Utility that enables you to automatically discover all

supported Cisco devices in the same local network segment as your

computer. You can get a snapshot view of each device or launch the

product configuration utility to view and configure the settings. For

more information, see www.cisco.com/go/findit.

b. The wireless access points are Bonjour-enabled and automatically

broadcast their services and listen for services being advertised by

other Bonjour-enabled devices. If you have a Bonjour-enabled

browser, such as Microsoft Internet Explorer with a Bonjour plug-in, or

the Apple Mac Safari browser, you can find the wireless access point

on your local network without knowing its IP address.

You can download the complete Bonjour for Microsoft Internet

Explorer browser from Apple’s website by visiting:

http://www.apple.com/bonjour/

c. Locate the IP address assigned by your DHCP server by accessing your

router or DHCP server. See your DHCP server instructions for more

information.

STEP 3 Launch a web browser, such as Microsoft Internet Explorer or Mozilla Firefox.

STEP 4 In the Address field, enter the default DHCP address and press the Enter key.

STEP 5 Enter the default user name of cisco and password of cisco in the User Name

and Password fields.

STEP 6 Click Login. The Wireless Access Point Setup Wizard appears.

STEP 7 Follow the Setup Wizard instructions to finish the WAP device installation. We

strongly recommend that you use the Setup Wizard for the first

installation.The Setup Wizard turns on the Wi-Fi radio, which allows you to

connect wirelessly. For more advanced configurations, see the

Administration Guide. A link to the Administration Guide is found in ,

page11.

Congratulations, you can now start using your wireless access point.

Cisco WAP125 Quick Start Guide 9

7Suggested Next Steps

Smart Power Source

Smart PoE is designed for detecting the power level from the PSE (Power Sourcing

Equipment) side; it does not matter whether 802.3at or 802.3af mode, the WAP581

will operate at the appropriate mode automatically.

Smart PoE ensures that the WAP581 remains functional once powered by 802.3af

PSE, and intelligently to adjust operations below:

•Second Ethernet port disabled

•2.4-GHz 802.11n radio in 2x2:2 spatial-stream mode

•5-GHz 802.11ac radio operates without restrictions

In case of an error while installing, try the following troubleshooting procedures

described in this section:

Troubleshooting

If you cannot display the configuration utility, you can test the ability of the

computer to communicate with the device by using ping.

To use ping on a computer running Windows:

STEP 1 Verify that the Cisco WAP581 is powered on and the lights indicate the

appropriate links.

STEP 2 Locate the device’s IP address. While there are different ways to locate your

device’s IP address, this procedure uses Cisco FindIT.

a. If you have previously downloaded Cisco FindIT, open Internet

Explorer and launch Cisco FindIT. For more information on

downloading Cisco FindIT, see www.cisco.com/go/findit.

b. In the Cisco FindIT display, place your mouse over the device’s name.

The device IP address is displayed along with other device

information.

STEP 3 Open a command window by choosing Start > Run and enter cmd.

STEP 4 At the command window prompt, enter ping and the device IP address. In this

example, we pinged 192.0.2.10.

If successful, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data: Reply

from 192.0.2.10: bytes=32 time<1ms TTL=128

Cisco WAP125 Quick Start Guide 10

If it fails, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data:

Request timed out.

Possible Cause of Installation Failure

No Power

•Power up the switch and your computer if they are turned off.

•Make sure your PoE switch is powered on and the lights indicate that you have

a link. See Verifying the Hardware Installation, page 6.

•Verify that the devices on your network are not plugged into a switchable

outlet.

Bad Ethernet Connection

•Check the state of the indicator lights. See Verifying the Hardware Installation,

page 6.

•Check the Ethernet cable to ensure that it is firmly connected to your devices.

Devices connected by the Ethernet cable can include the WAP device, and

routers, any switches, and your computer.

•Verify the connected switch has auto-negotiation enabled. The access point

and the switch need the same negotiation parameters set.

Bad Image

After a new firmware installation, if the Power light is solid red, contact system

support; see , page11.

Incorrect IP Address

The most likely cause of connectivity failure is an incorrect IP address. The Web

browser may be pointing to the wrong IP address, or your computer may be

configured with an IP address that is not in the same subnet as the device.

Because the factory default IP address configuration is DHCP, make sure that your

DHCP server is running and can be reached. You may need to disconnect and

reconnect the devices for them to discover their new IP addresses from the DHCP

server. You can then query the DHCP server for the new IP address. See Step 2 of

Getting Started with the Configuration, page 7 for more information on how to

find the DHCP address.

If the wireless access points do not receive a DHCP response (there is no DHCP

server on your network) after 60 seconds, the access points will fallback to the

following default static IP address: 192.168.1.245 and a default mask of

Altri manuali per Wap581

Indice

Altri manuali Cisco Punto di accesso wireless

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manuale

Cisco

Cisco 7330 Manuale utente

Cisco

Cisco Aironet AIR-AP1200 Manuale

Cisco

Cisco Meraki MR36 Manuale utente

Cisco

Cisco 1552S Manuale utente

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Manuale utente

Cisco

Cisco WAP121 Manuale utente

Cisco

Cisco 700 series Manuale utente

Cisco

Cisco 3310 Mobility Services Engine Manuale utente

Cisco

Cisco WAP150 Manuale utente

Cisco

Cisco WAP125 Manuale utente

Cisco

Cisco Linksys WAP610N Manuale utente

Cisco

Cisco ASR 1001 Manuale

Cisco

Cisco Meraki MR28 Manuale utente

Cisco

Cisco Aironet 1530 Series Manuale

Cisco

Cisco Linksys WAP54G LA Manuale utente

Cisco

Cisco AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access... Manuale

Cisco

Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access... Manuale

Cisco

Cisco AIR-AP1572IC Manuale

Cisco

Cisco Small Business AP541N Manuale utente

Cisco

Cisco WAP121 Manuale utente

Cisco

Cisco Aironet 1600 Series Guida di riferimento rapido

Cisco

Cisco Meraki GR60 Manuale utente

Cisco

Cisco Aironet LAP1522 Manuale

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente