Clarke CWB300LS Manuale utente

ASSEMBLY INSTRUCTIONS

GC0416

WORKBENCH WITH SHELF

PART NO: CWB300LS

Part No: 7637870

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE workbench.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATION

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Model CWB300LS

Dimensions (L x W x H) 1500 x 750 x 895 mm

Weight 25.2 kg

Maximum rated load 300 kg (worktop)/100kg (shelf)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. Always read these instructions before use.

2. Always wear protective gloves when assembling the workbench.

3. It is recommended that the assembly be done by two persons.

4. Not following these instructions could result in the workbench falling over,

causing damage to equipment and personal injury.

5. Never carry out any alterations or modifications to this product or use the

workbench for a purpose for which it was not intended.

6. Never allow children to climb on the workbench.

7. Always ensure the load is positioned centrally and evenly distributed.

8. If replacing parts, only use those supplied by Clarke International.

9. Do not exceed the maximum rated load of 300 kg (bench/100kg (shelf) as

stated on the warning labels.

10. Only use on a flat, level surface capable of supporting the workbench and

its maximum load.

11. Always ensure you are working on a firm flat surface, and that the

workbench is completely stable.

12. Take care when placing a heavy load on to the bench. It should be

placed gently so that the strain is taken up gradually.

13. Always keep the work areas clean and well lit.

14. Check for damaged parts before using the workbench. Any part that

appears damaged should be carefully checked to determine that it will

perform its intended function. Replace any damaged parts as soon as

possible.

15. Keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING & INVENTORY

When unpacking, check for damaged or missing parts. Any deficiencies

found should be reported to your CLARKE dealer where the product was

originally purchased.

Do not dispose of damaged components or packaging with general

household waste. They should be taken to a recycling centre and disposed of

appropriately. This product should include the following;

No Description Quantity

ACornerPost 4

B Long Support Beam 3

C Centre Support 1

D Short Support Beam 2

ELowerEndBeam 2

F Worktop Support Beam 2

G Worktop Panel (see front cover picture) 1

H Location Plate 4

J Lower Shelf (see front cover picture) 1

K Lower Shelf Supports 2

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

TOOLS REQUIRED

• Rubber mallet or hammer

• Protective cloth/wood block

ASSEMBLY PROCEDURE

1. Assemble on a firm, level surface. Avoid assembly on a domestic carpet.

2. Always ensure that the tabs sit at the bottom of the slots.

3. It is recommended that the assembly should be done by two persons.

4. Use a cloth or softwood block to

protect the surface finish of the

product when using a mallet.

5. The tabs of the beams will often

enter the slots fully using just firm

hand pressure but if they are too

tight, you may require a rubber

mallet to assist. If so, always use a

cloth to protect the product paint

finish.

6. Tap gently with the mallet to drive the tabs of the beams fully into the slots

in the corner post. Always strike the edge close to the post.

7. Decide how high you want the lower beams to be, relative to the floor,

noting that the lower beams should never be more than half height from

the bottom of the corner posts.

8. Use the short support beams (D) to

connect the front and rear corner

posts together. Ensure the beam

(D) is in the highest possible

position.

NOTE: The beam edge with the

wider flange should be

installed uppermost to

support the worktop.

9. Add the lower end beam (E) with

the two connecting slots). Repeat this again for the other end assembly,

making sure that the corresponding lower end beams are at the same

height.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

10. Use the long support beams to

connect the two end assemblies

together as shown in Fig 3.

11. Add the centre support beams

(F), by bending the flexible tabs to

90 degrees and slotting them into

place as shown in Fig 4.

12. Finally bend the tabs back 180

degrees to lock securely.

13. Connect the centre support (C)

to the lower end beams (E) by

bending the flexible tabs to 90

degrees and slotting them into

place. Finally bend the tabs back

180 degrees to lock in place.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

14. Add the remaining long beam (B)

followed by the lower shelf

supports (K) to creat the lower

framework.

15. Position the bench on the plastic

feet.

16. Lay the worktop panel (G) into

position on the support beams.

• Always fit the worktop at the

highest possible position.

17. Add the lower shelf (J) in position.

SPARE PARTS

In the event of damage, spare parts are available from the Clarke

International parts department.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Deposito attrezzi

Clarke

Clarke CWB1700P Manuale di istruzioni

Clarke

Clarke CWB1250 Manuale utente

Clarke

Clarke CWB2001P Manuale utente

Clarke

Clarke CHB1500 Manuale utente

Clarke

Clarke CWB1201E Manuale utente

Clarke

Clarke CERT1225 Manuale utente

Clarke

Clarke CWB1000 Manuale utente

Clarke

Clarke CWB114 Manuale utente

Clarke

Clarke CWB1250 Manuale utente

Clarke

Clarke CMUS3 Manuale utente

Clarke

Clarke CWBR1B Manuale utente

Clarke

Clarke CWB1630R Manuale utente

Clarke

Clarke CWC38 Manuale utente

Clarke

Clarke CWB1500D Manuale utente

Clarke

Clarke CWB80B Manuale utente

Clarke

Clarke CWB57 Manuale utente

Clarke

Clarke CWB300 Manuale utente

Clarke

Clarke CPF13 Guida alla risoluzione dei problemi

Clarke

Clarke CWB1205P Manuale utente

Clarke

Clarke Metalworker CBGS2 Manuale utente

Clarke

Clarke CWB1200E Manuale utente

Clarke

Clarke PC4 Manuale utente

Clarke

Clarke CWB1530 Manuale utente

Clarke

Clarke CMPW1 Manuale utente

Manuali Deposito attrezzi popolari di altre marche

Ryobi

Ryobi RWB03 Manuale utente

Husky

Husky H27CH5TR4BGK Manuale utente

Scheppach

Scheppach ts 2100 Manuale utente

Cornwell Tools

Cornwell Tools CTB360AKBK Manuale utente

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Manuale utente

Cassese

Cassese CS200 CART Manuale utente

Kendall Howard

Kendall Howard ESDW-9630-1000 Manuale utente

Lista

Lista Align Istruzioni per il montaggio

Workzone

Workzone 99609 Manuale utente

Stanley

Stanley STST83800-1 Manuale utente

Homak

Homak PROFESSIONAL Series Manuale del sistema

Perel

Perel ROLLER SHUTTER STORAGE CABINET Manuale utente

Husky

Husky H5CH2R Manuale utente

BGS technic

BGS technic 4107 Manuale utente

Ryobi

Ryobi RWB02 Manuale utente

Husky

Husky H52CH6HDV3WHT Manuale utente

Sealey

Sealey PTB66004 Manuale utente

General International

General International Excalibur 40-100 Manuale elenco delle parti