CLEAN Instruments PH200 Manuale utente

MODE

ESC

CAL

INFO

SET

ENT

HOLD

DO200

CLEAN INSTRUMENTS

2006, No.511 Tianmu W. Rd. Shanghai 200070, China

11F No.25,Siwei St., Zhonghe Dist.,New Taipe City 23570, Taiwan

www.cleaninst.com

2013.07

www.cleaninst.com

Meter

PH200/CON200/DO200

Operation Manual

Conductivity / TDS / Salinity

Dissolved Oxygen

Customer Service: [email protected]

PH200CON200DO200

pH／ORP

Dissolved oxygen(mg/L)

14.64

14.22

13.82

13.44

13.09

12.74

12.42

12.11

11.81

11.53

11.26

11.01

10.77

10.53

10.30

10.08

9.86

9.66

9.46

9.27

Temperature°C

Dissolved oxygen(mg/L)

9.08

8.90

8.73

8.57

8.41

8.25

8.11

7.96

7.82

7.69

7.56

7.43

7.30

7.18

7.07

6.95

6.84

6.73

6.63

6.53

Temperature°C

7.7.3 Factory defaults

Corresponding interface

P - 01

P - 02

P - 04

P - 05

Item

Atmospheric Pressure

Salinity

Auto Lock

Auto power off

Backlight

Unit of the displayed value

Factory Defaults

1013 mBar

0.0 g/L

OFF

7.7.2 Water saturated dissolved oxygen in different temperature

(Atmospheric Pressure 101325Pa100% RHSalinity 0‰)

TABLE OF CONTENTS

1 Preface

1.1 Before Use

1.2 In Use

1.3 Safety

2 Basic Operation

2.1 Battery

2.2 Electrode Installation

2.3 Shell

2.4 Power on/off and Backlight

3 Key Panel

3.1 Key instruction

3.2 Key function

4 Appearance

4.1 Display

4.2 Display Character Table

5.1 Technical Specifications

5.2 Browse the parameter

5.3 pH Set UP

5.3.1 P01 pH Standard Solution

5.3.2 P02 Manual Temperature setting

5.3.3 P03 Temperature Offset setting

5.3.4 P04 Auto Lock Function setting

5.3.5 P05 Auto Power Off Setting

5.3.6 P06 Clearing Memory Function

5.3.7 P07 Reverting to Factory Default Setting

5.4 Calibration Mode

5.5 Measurement Mode

5.6 Storage of Data

5.7 Calibration Parameter and Setting Parameter

5.8 Appendix

6.1 Technical Specifications

6.2 Browse the parameter

6.3 Set UP

6.3.1 P01 Cell Constant (K)

6.3.2 P02 Temperature Compensation Base

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

pH / ORP

Conductivity / TDS / Salinity

Average Atmospheric Pressure ph/kPa

101.3

100.1

98.8

97.6

96.4

95.2

94.0

92.8

91.7

90.5

89.4

88.3

87.2

86.1

85.0

84.0

82.9

81.9

80.9

79.9

78.9

77.9

76.9

76.0

75.0

74.1

73.2

72.3

Altitude h/m

2800

2900

3000

3100

3200

3300

3400

3500

3600

3700

3800

3900

4000

4100

4200

4300

4400

4500

4600

4700

4800

4900

5000

5100

5200

5300

5400

5500

Average Atmospheric Pressure ph/kPa

71.4

70.5

69.6

68.7

67.9

67.0

66.2

65.4

64.6

63.0

62.2

61.4

60.7

59.9

59.2

58.4

57.7

57.0

56.3

55.6

54.9

54.2

53.5

52.9

52.2

51.6

50.9

Altitude h/m

100

200

300

400

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

2100

2200

2300

2400

2500

2600

2700

7.7.1 The corresponding Average Atmospheric Pressure with the Altitude

7.7 APPENDIX

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝

噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝噝

6.3.3 P03 Conductivity Temperature Factor

6.3.4 P04 TDS Factor

6.3.5 P05 Temperature modified Factor

6.3.6 P06 Auto Lock Function Setting

6.3.7 P07 Auto Power Off Setting

6.3.8 P08 Clearing Memory Function

6.3.9 P09 Reverting to Factory Default Setting

6.4 Setting Parameter

6.5 Calibration

6.6 Appendix

6.6.1 Conductivity sensor measuring range

6.6.2 Factory Defaults

7.1 Technical Specifications

7.2 Browse the parameter

7.3 Set UP

7.3.1 P01 Atmospheric Pressure

7.3.2 P02 Salinity Compensation

7.3.3 P03 Temperature Offset

7.3.4 P04 Auto Lock Function Setting

7.3.5 P05 Auto Power Off Setting

7.3.6 P06 Clearing Memory Function

7.3.7 P07 Reverting to Factory Default Setting

7.4 Calibration

7.5 Measurement Mode

7.6 Storage of Data

7.6.1 Storage of measuring data

7.6.2 Browse on data storage

7.6.3 Setting parameter

7.7 APPENDIX

7.7.1 The corresponding Average Atmospheric Pressure with the Altitude

7.7.2 Water saturated dissolved oxygen in different temperature

7.7.3 Factory defaults

8 GENERAL INFORMATION

8.1 Warranty

8.2 Return Of Malfunction Instruments

8.3 Guidelines Or Returning Unit For Repair

Dissolved Oxygen

DO200

1 Preface

1.1 Before Use

1.2 In Use

The meter may only be carried out by trained experts.

1.3 Safety

Unqualified meter should not be installed and used.

The meter should be used under the required working condition.

The meter should not be opened and repaired by clients themselves.

Please make sure to cut the power off when you open the cover to carry on any operation.

Thank you for selecting CLEAN meter.

Although the meter use advanced technology and meet

the requirements of current safety rules, improper use can still threaten the safety of users, and / or

cause harmful influences to factory and other equipments. Therefore, before using the

meter, relevant person must read and understand contents of this operation manual.

Operation manual should be kept accessible within the person who use the meter.

If you have problems which are not mentioned or can not be explained in this manual, please

contact CLEAN local customer service center. They will be very glad to help you.

Modified meter should not be used. Manufacturers and suppliers do not bear

responsibility for the damage and lost caused by modifying instruments without

permission. Clients should bear all the risks.

This instrument is IP67 rated. Please use waterproof cable glands when you connect

the cable. Also,please loose it when you open the cover. After connecting the

cable, please tighten the cable conductor according to the following instruction

with cable ties, or it will cause danger such as cable conductor or interface falls off

when open the cover.

On any unmentioned use or the use that contradict with the technical parameters the operators

should bear the responsibility.

Other conditions of right use include:

- Remarks and requirements stated in operation manual.

- Local safety regulations on safe operation.

- Information and warning of products that are used together with the meter in the contract.

(chassis, electrode, etc.)

- Required operating environment and working condition.

7.6.3 Setting parameter

1. Long press to enter into Setting parameter when in measurement mode. Press to

check through all the parameters.

2. Press to quit and go back to measurement mode.

0140

DO200

2 Basic Operation

2.1 Battery

2.4 Power on/off and Backlight

Use the coin to remove the battery cover by following the “-” direction.

Insert 2*7AAA batteries in the battery compartment with the correct Positive and Negative poles.

Tight the battery cover by following the “+” direction.

2.2 Electrode Installation

2.3 Shell

You can refer to the Electrode operation manual for use and maintenance. The direction of the red

dot marker on the Electrode and the salient point on the unit should be the same when install the

electrode to the unit. Remove the electrode by pulling out the clamp on the electrode.

This series of meter is portable and water-proof, with IP67 rated. If the meter accidentaly touches

water or other fluids, pls wipe it clean immediately. The meter function is not affected usually. But if

affected and cannot use, (possibly because of the battery cover is not tight and penetrated by

water). Please contact our company or CLEAN local customer service center. They will be very glad

to help you.

Power on

Short press power on/off key to start the meter. You can hear the indicator tone and whole screen

displayed within 1 second.

Power off

Long press the power on/off key to power off the meter.

Auto power off in 10 minutes if without any operation.

LCD backlight

Short press power on/off key to control if turn on the backlight or not.

7.6.1 Storage of measuring data

7.6.2 Browse on data storage

7.6 Storage of Data

1.If you need to save the measuring data once it is stabilized, press , the Lot no. will be shown

on the upper right of the screen. Press “ ” to save the data. You can also press to not

save. The meter will automatically go back to measurement mode after data saved. The unit at

most can save 50 sets data. The screen will show “OVER” if more than 50 sets reminds you the

memory card is full.

2.Enter into setting mode P-06 if you need to delete the saved data forever. You can refer to

Clearing memory function.

1. Press to enter into the browse on the data storage , the Lot no. will be shown and data

twinkling. Press to check all the saved data. Press to go back to measuring mode. If

showed “NONE” means no data is saved yet.

2. If you quit and re-entering during checking the data, the meter will freeze in the last set of data.

3902

DO200

PH200 CON200

DO200

SET

ENT

HOLD

DO200

7.5 Measurement Mode

1. You can first set the meter per your request. Otherwise, the setting will be factory defaults.

2. Before each measuring, first lay aside the electrode for around 15mins to fully activate the

sensor after the electrode is connected with the meter.

3. After power on, press to select the operation mode (% or mg/L).

4. Immerse the electrode in the solution and stir gently. The measuring mark will twinkle. You can

read the value once the data is stabilized and shows the stable symbol .

5. If the Auto Lock Function is ON, the meter can lock the measured value after the reading had

stabilized and display . Press to unlock.

6. If the changed temperature is needed, you can refer to P-03 Temperature Offset.

3 Key Panel

Key Description

Power on

ON/OFF backlight

Long press to Power off

Mode switch

Exit from current mode operation

Data setting

Enter into calibration mode

Long press to enter into parameter browsing

Freeze or unlock the displayed value

Store the displayed value into memory

Increment values or scroll through the next options available

Recall stored values from the memory

Decrement values or scroll through the next options available

Short press: Short press means release the key once after pressing. (If there is no mark out below,

default it as Short press)

Long press: Long press means press the key for 3 seconds and release.

Hold: Hold means not release the key, used in adjusting data and accelerate after a certain time.

Not release the key until the value is set as needed.

3.2 Key function:

3.1 Key instruction

0338

DO200

7.4 Calibration

Illustration on the calibration point symbols:

1. The“Air” is shown at the right bottom of the screen during and after air calibration.

2. The “Zero” is shown at the right bottom of the screen during and after air calibration.

3. Both“Air” and “Zero” is shown after 2 points calibration.

Note:

You can press back to the measurement mode during calibration and all the calibration

point is saved. When the measured signal is out-ranged, the sign “Err” will be showed, possibly

the aging electrode or the polluted standard solutions lead to this.

1. In measurement mode, press to enter calibration process. .

2. First point calibration-100% air calibration: put the sensor in air, after you get a stable value or the

stable symbol shows up, press key to confirm 100.0% saturated dissolved oxygen point.

3. After pressing , the electrode Slope will be showed on the screen. Then automatically

initiate second point calibration -0% point calibration.

1. Dip the sensor in standard solution, when the value is stable, press key to confirm 0% point.

Then system go back to measurement mode.

2. If you need to adjust the Atmospheric Pressure Compensation and the Salinity Compensation

according to local situation. You can set in P-01 and P-02.

Note: Factory defaults first point 100% air calibration. If you don’t need to calibrate 0% point,

press key to go back to measurement mode.

After air calibration, the meter will automatically initiate second point calibration:

4 Appearance

1 Measuring Status-Calculating

2 Measuring Status-Stable Value

3 Electrode inserted display

4 Setup display

5 Offset - Electrode Offset

6 Slope - Electrode Slope

7 Done - Calibration Done

8 mVȠPHȠmAȠc$Ƞ%mSȠuSȠc$Ƞmg/LȠppmȠpptg/LmBar - Unit of Measurement

Auto / Manual - Temperature Compensation

10 4.01Ƞ7.00Ƞ10.01

Calibrated Points -USA Buffer Standard

4.01Ƞ6.86Ƞ9.18

Calibrated Points - NIST Buffer Standard

4.1 Display

3704

DO200

4.2 Display Character Table

Sensor

Automatic Temperature Compensation

Manual Temperature Compensation

Automatic Temperature Compensation

Manual Temperature Compensation

Electrode Slope

autolock

Auto Off

no stored data

Clear data

place of the stored data

Sensor Offset

Menu item

Password Setting

Factory Defaults

Sensor Slope 1

Sensor Slope 2

Save Data

Error

Off

Yes

Temperature value Over

Temperature value Under

Full Data Storage

Measuring Value Over

Measuring Value Under

TDS

Salinity

Temperature Base

Coefficient

Offset

nA output of electrode

Sensor slope

Atmospheric pressure

Salinity

mg/L

DO electrode voltage

Buffer Solution

NIST Standard

USA Standard

7.3.7 P07 Reverting to Factory Default Setting

In P-07, you can select NO or YES to not reverting or reverting to factory settings by pressing .

Please refer to above description steps to set up P-07.

If select YES, the meter will revert all the settings to factory defaults and all the settings will lost

forever. The unit will restart at the same time.

You can go to next parameter setting by pressing , or pressing key to quit and go

back to measurement mode.

Note:

1. During setting, you can press key to quit setting whenever necessary.

2. During setting, you can adjust anything twinkling by pressing . If it is the data

twinkling, you can speedy adjust the data by pressing .

0536

DO200

New design, Comfortable holding, Easy carrying , Simple Operation

65*40mm, large LCD with backlight for easy meter information reading

IP67 rated, dustproof and waterproof, Floats on water

Up to 3 points auto-buffer-recognition: Zero offset, Slope of Acid/Alkali

segment, Ensure accurate measuring results for the full range

One key to check through all the settings, including: Zero offset, Slope

of Acid/Alkali segment, and all the settings

Auto lock function

50 data sets memory stores and recalls

Auto Power off saves battery after 10-mins non-use

2*1.5V 7AAA battery, long battery life

CP337 Operating Carrying Pouch

PH200 Meter

pH / ORP 7.3.6 P06 Clearing Memory Function

In P-06, you can set the Clearing Memory Function.

Please refer to above description steps to setup P-06.

If select YES, the meter will clear all the saved data.

You can go to next parameter setting by pressing , or press key to quit and go

back to measurement mode.

3506

PH200

DO200

PH200

MODE

ESC

CAL

INFO

SET

ENT

HOLD

5.1 Technical Specifications

Range

Resolution

Accuracy

Range

Resolution

Accuracy

Range

Resolution

Accuracy

Power supply

Working time

NIST

USA

Environment

Memory

-2.00 16.00 pH

0.01 pH

±0.2% F.S.

-2000~2000 mV

1 mV

± 0.2% F.S.

-10.0 °C~110.0 °C

0.1 °C

± 0.2 °C

2*7 AAA batteries

>500 hrs

4.006.869.18

4.017.0010.01

-5 °C~60 °C, Relative humidity90%

50 sets

ORP

Temperature

Power

pH Buffer Kinds

Others

5.2 Browse the parameter

7.3.4 P04 Auto Lock Function Setting

7.3.5 P05 Auto Power Off Setting

In P-04, you can set the Auto Lock Function.

Please refer to above description steps to setup P-04.

If the Auto Lock Function is ON, the meter can lock the measured value after the reading had

stabilized and display . Press to unlock.

You can go to next parameter setting by pressing , or press key to quit and go

back to measurement mode.

In P-05, you can set the Auto Power Off Function.

Please refer to above description steps to setup P-05.

If the Auto Power Off is ON, the meter will power off if no operation in 10mins.

You can go to next parameter setting by pressing , or press key to quit and go

back to measurement mode.

0734

PH200

DO200

Long press for 3 seconds in measurement mode.

Then press 　　　　　　　　　　 or 　　　　　　　　　 to browse the parameters

1. Zero offset

2. Slope

3. High/Low segment of the slope

4. Buffer kinds

5. Temperature compensation

6. Hold Auto Lock

7. Auto power off

8. Battery power

Altri manuali per PH200

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CLEAN Instruments Strumento di misura

CLEAN Instruments

CLEAN Instruments DH200 Manuale utente

CLEAN Instruments

CLEAN Instruments PH500T Manuale utente

CLEAN Instruments

CLEAN Instruments PH200 Manuale utente

CLEAN Instruments

CLEAN Instruments DH30 Manuale utente

CLEAN Instruments

CLEAN Instruments DH30P Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente