Clevertronics CLP LIFELIGHT PRO Specifiche tecniche

1942295

V1.0

8 June 2021

UK Instruction Sheet Template – V1.1 – Updated: 20/11/2020

Zoneworks, HIVE and DATA Monitored Options

Fittings with part numbers -ZW, -HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also

be connected via Ethernet/Internet/Fibre)

. Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HVG, DATA

Commissioned

LED on Solid (Green)

ZW, DATA Un-commissioned Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HVG

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HVG Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI fitting please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Light

ing Control System

Commissioning Technicians and not Clevertronics

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way

“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections

are marked as Da Da.

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Maintained fittings (CLIFEM-PRO-xx) cannot be scanned with a camera using the Clevertest Plus App

as the maintained light source interferes with the camera scanning function. To register the fitting

manually enter the serial number from the QR code and visually read the test result and enter manually

into Clevertest Plus App.

CLP™ LIFELIGHT PRO Surface Mount

Emergency Luminaire

Installation & Maintenance Instruction Leaflet

NOTE: Standard product codes with this symbol

are enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Australia (Head Office)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

IP20

UK OFFICE

Website: www.clevertronics.co.uk

362 Stockley Close

West Drayton UB7 9BL

Phone: 01895 430 255

Models:

CLIFEz-PRO-aa-SMC-bb-xx-yy

Testing :

Options:

Manual Test

xx = Blank

Maintained

z = M

Zoneworks

xx = ZW

Non-Maintained

z = Blank

Z/W DATA

xx = DATA

Colour, Black

yy = BLK

Zoneworks Hive

xx = HVG

Warm White

aa = WW

DALI Registered

xx = DALI

Switched Live(Active)

bb = SA

Spare Parts:

1550230

BATT:LP 3.2V 6400mAh.200mm lead.Brkt.

1100811

Lifelight Pro,Head Assem,Ld:280mm,Round,Gen2,LT (Daylight White)

1100809

Lifelight Pro Head Ass,Ld:280mm,Rnd,Gen2,Blk,LT (Daylight White, Black)

1100821

Lifelight Pro,Head Assem, Ld:280mm,Rnd,WW,Gen 2 (Warm White)

1100808

LifelightPro,HeadAss, Ld:280mm,Rnd,WW,Gen 2,Blk (Warm White, Black)

UKM02370030002

CLIFE-PRO-SMS-CKIT-IC2-475, Lifelight Pro, Control Only, 475mA, LP, CTP, OWC

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant British Standards.

1942295

V1.0

8 June 2021

UK Instruction Sheet Template – V1.1 – Updated: 20/11/2020

Installation:

This CLIFE-PRO-SMC Surface Mount Emergency Luminaire can be installed on solid or T-BAR ceilings

or used to replace an existing unit.

•Locate the installation position.

•Refer Images and Dimensions below for the mounting hole dimensions.

•Pre-drill mounting holes.

•Mount ceiling mounting bracket and use suitable fixings to secure the bracket into the pilot holes.

•Bring in supply cables via the top entry hole (surface mount conduit entry).

•Terminate the supply cables to the L, N & E terminals (for -SA, terminate the Switched Live(Active)

to Lsw, for –DALI or –DATA fittings terminate the DALI or DATA cable to the terminals marked Da

Da or DATA).

•Install Cylinder containing the control gear, ensuring to connect the supply cable to the connector

from the supply terminal block.

•Locate and fit securing screws on sides.

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four

Segment Marking on the product will include an ‘’F’’ in third segment block.

•For -HVG fittings, screw in the supplied antenna to the antenna connector accessible on the

external surface.

•Wall mounting bracket optional, comes with additional instructions.

•The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer

than 350mm is not expected.

Images and Dimensions:

Ceiling Mounting Bracket

Optional Wall Mounting Bracket

Luminaire Dimensions

245mm (L) x 128mm (D)

Mounting Hole Dimensions

35mm x 90mm

Mounting Hole Dimensions

70mm x 70mm

Weight

0.7kg

Weight

1.9kg

Part Number White

2740045

Part Number Black

2740048

Note:

This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-

user replaceable light source and battery - to be replaced (if required, refer installation instructions for

battery replacement) by Clevertronics service personnel/agents or a registered electrician.

Battery Replacement:

1. Prior to any work, isolate the power to the luminaire that requires battery replacement.

2. Open the fitting by removing the securing screws on sides, support cylinder while removing screws.

3. Disconnect the Supply Connector. The Luminaire is now isolated from the Mounting Bracket.

4. Remove screws from Top Bar and the Gear Tray assembly can be removed.

5. Remove the Battery Connector from the Emergency Driver.

6. Remove the battery from the gear tray by removing mounting screws.

7. Replace battery, re-install screws and connecter to Emergency Driver.

8. Reinstall the Gear Tray, ensure the Top Bar is aligned at 90 degrees (1/4 turn) to the side securing

screw holes.

9. Reconnect the Supply Connector and fit the securing screws on sides to secure the luminaire into

the Mounting Bracket.

Testing Procedure:

When the luminaire is connected to the un-switched Live, it must be allowed to charge the battery for at

least 24 hours. The emergency lamp only illuminates during a power fail. Conduct the following tests:

•The emergency lamp must illuminate for at least 180 min after disconnection from the mains. The

results of all tests are required to be recorded in a service logbook, which is to be kept on-site at all

times. If the unit fails to illuminate for the requisite time, remedial action must be taken to repair the

situation and once completed, the unit must pass a subsequent test.

•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.

•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Below are a list of common problems and their possible causes:

Fault: The Green LED indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected.

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The Li-ion battery in the Exit & Emergency Unit has been selected to give

excellent long life performance in a controlled IEC 60598-2-22 testing environment. Excessive battery

cycling will reduce through-life performance and may lead to premature battery failure. Battery warranty

claims, as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

https://clevertronics.co.uk/product-warranty-statement/

Altri manuali Clevertronics Attrezzatura di illuminazione

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics FBKLED Series Manuale di istruzioni

Clevertronics

Clevertronics L10 LJWELED-40 Series Manuale utente

Clevertronics

Clevertronics L10 LWFLED 2IPREM Series Manuale di istruzioni

Clevertronics

Clevertronics L10 LIFELIGHT PRO Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LED CIRCLITE Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics Argonaut PLUS Guida alla manutenzione e all'assistenza

Clevertronics

Clevertronics ARGOPRO-1200 Series Manuale utente

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manuale utente

Clevertronics

Clevertronics TS EUBPRO-LI Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manuale utente

Clevertronics

Clevertronics L10 Cleverfit Pro Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LUBPRO Series Manuale

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP CBS2LEDS-DIF Series Specifiche tecniche

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Istruzioni per l'installazione e il funzionamento

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente