CNC4PC C82 Manuale utente
___________________________________________________________________________
User’s Manual Page i
USER’S
MANUAL
VER.1
C82- MULTIFUNCTION CNC BOARD
Rev. 3.2
MARCH 2020
___________________________________________________________________________
User’s Manual Page ii
USER'S MANUAL TABLE OF CONTENTS
Contents Page #
FEATURES.....................................................................................................................1
I/O SPECIFICATIONS.....................................................................................................2
BOARD DESCRIPTION..................................................................................................2
POWER TERMINALS AND CONFIGURATION JUMPERS............................................3
4.1 Power terminal...........................................................................................................3
4.2 Source Output 5VDC.................................................................................................3
4.3 Source Output 10-24VDC..........................................................................................3
4.4 Input terminals for port_1 and port_2 ......................................................................4
4.5 Select JUMPER COM for the inputs of port_1 and port_2......................................5
JUMPER POSITION .......................................................................................................6
5.1 Selecting the SCHP operation mode........................................................................6
5.2 Jumper configuration driver enable.........................................................................7
5.3 Jumper configuration driver fault.............................................................................7
5.4 Configuration jumper pin 16 or 17............................................................................7
CONNECTION EXAMPLE FOR SHIELD C78 ................................................................8
6.1 RJ45 shield C78 connection for axes, Limits and Encoder....................................8
6.2 RJ45 shield board description..................................................................................8
6.3 Pinout.........................................................................................................................9
7.0 CONNECTION EXAMPLE FOR SHIELD C77 ..............................................................10
7.1 Terminal Shield Screw-on.......................................................................................10
7.2 Shield board description .........................................................................................10
DRIVER DISCONNECTION JUMPERS........................................................................11
E-STOP TERMINAL......................................................................................................11
TYPICAL CONNECTIONS............................................................................................12
LED INDICATOR ..........................................................................................................13
DIMENSIONS................................................................................................................15
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 1
FEATURES
•Designed for ESS AND ETHER-MACH motion controller.
•Built-in PWM-Based Speed Control and Two Built-in Electromechanical
Relays with NO and NC positions for spindle control.
•The system monitors:
-E-Stop.
-Safety Charge Pump.
-VFD Fault.
-Driver Fault.
•Optoisolated inputs working at 5-24VDC.
•Outputs can be 500mA open collector or +5vdc at 50mA TTL.
•Buffered outputs.
•Electromechanical Relay with NO and NC positions for general purpose
(Port_2 16 or 17, jumper-selectable).
•Microcontroller based SCHP.
•Can be powered with a voltage between +10 and +24VDC.
•Status LEDs on all input and Output connections.
•DIN Rail mountable.
•Pluggable Screw-On Terminals.
•It is compatible with family of C34 connector boards that allow quickly
connecting to popular drives connecting not just the step and direction
signals, but also the fault and enable signals.
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 2
I/O SPECIFICATIONS
OPTOISOLATED DIGITAL INPUT TTL SPECIFICATIONS
On-state voltage range
5 to 24VDC
Maximum off-state voltage
0.8V
Typical signal delay
2.8uS
DIGITAL OUTPUT TTL SPECIFICATIONS
Maximum output voltage
5VDC
Maximum output current
24mA
Maximum off-state voltage
0.44 V
Maximum supported frequency
400KHz
Typical signal delay
10nS
Time of transition to high impedance state
12nS
BOARD DESCRIPTION
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 3
POWER TERMINALS AND CONFIGURATION JUMPERS
4.1 Power terminal
The board requires an external power supply which can deliver 10-24VDC@700mA to power
the logic of the board and the ESS or ETHER-MACH, but keep in mind that each output can
deliver up to 500mA and if powering other breakout or relays boards. So, you will need to add
all the expected power consumption.
4.2 Source Output 5VDC
4.3 Source Output 10-24VDC
10-24VDC can be sourced to sensors or other cards requiring it.
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 4
4.4 Input terminals for port_1 and port_2
These terminals support signals 5-24VDC, you can connect sensors NPN, PNP, switches,
capacitive sensors, etc. set jumpers depending on signal voltage.
PORT_1
Jumper position change
PORT_2
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 5
4.5 Select JUMPER COM for the inputs of port_1 and port_2
Set the Jumper to COM = +5VDC, GND or 10-24VDC to determine the common for the input
signals to be used.
COM = 5V
PORT_2 PORT_1
COM = GND with 5VDC
COM = GND with 10-24VDC
COM = 10-24VDC
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 6
JUMPER POSITION
5.1 Selecting the SCHP operation mode
The Safety Charge Pump uses pin 17 on port 2. When the SCHP is enabled on the board, then
the output of the terminals will be active while the Safety Charge Pump signal is present and
inactive while the SCHP is not present.
1-2: SCHP ON 2-3: SCHP OFF
Note: also, that Relay3 on can also be tied to pin 17 or 16 on port 2. If the jumper is set to be
tied to pin 17, then the relay will activate while the system is active. This can be ideal to control
power to DC servos or to handle servo brakes. Or enable/disable any other feature that is
associated to the system been active.
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 7
5.2 Jumper configuration driver enable
1-2: Driver enable ON 2-3: Driver enable OFF
5.3 Jumper configuration driver fault
1-2: Driver fault ON 2-3: Driver fault OFF
5.4 Configuration jumper pin 16 or 17
1-2: PIN17 2-3: PIN16
____________________________________________________________________________
___________________________________________________________________________
User’s Manual Page 8
CONNECTION EXAMPLE FOR SHIELD C78
6.1 RJ45 shield C78 connection for axes, Limits and Encoder
6.2 RJ45 shield board description
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali CNC4PC Sistema di controllo
