Code Alarm CATX120 Istruzioni operative

Model CATX120

Programming Guide

The keychain transmitters included with the system have

been pre-programmed at the factory, with each button pre-

assigned to control a specific function of the system.

It is important to remember that during programming, each

individual step of the procedure must be executed within 15

seconds of the previous step.

When the 15 second time limit is allowed to expire, the

system will automatically terminate the programming mode.

This is indicated by a long chirp from the siren.

Additionally, the system will store codes from up to 4

different transmitters. If a 5th transmitter is programmed to

any receiver channel, then the first transmitterprogrammed

to that channel will be erased from the system’s memory.

To program new or additional transmitters, the alarm must

be disarmed and the valet switch must be in the OFF

position:

1. Enter the vehicle, and turn the ignition key to the ON

position.

2. Press and release the valet/programming/override

switch 3 times.

3. The dash LED will flash one time, and the sounding

device will beep one time, indication the system is ready to

accept programming for transmitter 1.

4. Press and hold the Arm Icon button until the sounding

device emits a long beep, indicating the signal has been

stored into memory.

5. If you have additional transmitters (up to 4) that need to

be programmed, repeat step 4 for each transmitter.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one. Be

sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX120

Programming Guide

Indice

Altri manuali Code Alarm Allarme auto

Code Alarm

Code Alarm Procomp Manuale utente

Code Alarm

Code Alarm CSI-300 Manuale utente

Code Alarm

Code Alarm CA 6551 SST Manuale utente

Code Alarm

Code Alarm caSEC Manuale di installazione e funzionamento

Code Alarm

Code Alarm Professional 1000 Manuale utente

Code Alarm

Code Alarm ca 1552 Professional Series Manuale utente

Code Alarm

Code Alarm CA 6151 Manuale utente

Code Alarm

Code Alarm Car Alarm Manuale utente

Code Alarm

Code Alarm CA 1550 Manuale utente

Code Alarm

Code Alarm CA1B5 Manuale utente

Code Alarm

Code Alarm UTXPR Manuale del proprietario

Code Alarm

Code Alarm Professional caSECRS Manuale utente

Code Alarm

Code Alarm CATX520 Istruzioni operative

Code Alarm

Code Alarm ca 1151 Manuale utente

Code Alarm

Code Alarm ca 1051 Manuale utente

Code Alarm

Code Alarm Professional Series CA 1550 Manuale utente

Code Alarm

Code Alarm CA 421 Manuale utente

Code Alarm

Code Alarm CA 310 Manuale utente

Code Alarm

Code Alarm TW-1 Manuale utente

Code Alarm

Code Alarm ca1554 Manuale utente

Code Alarm

Code Alarm PROFESSIONAL SERIES CA 1551 Manuale utente

Code Alarm

Code Alarm CA100 Manuale utente

Code Alarm

Code Alarm CA 180 Manuale utente

Code Alarm

Code Alarm 2000 Manuale utente

Manuali Allarme auto popolari di altre marche

Clifford

Clifford 3606X Manuale utente

Ultra Start

Ultra Start 2500M SERIES Manuale utente

Ultra Start

Ultra Start 650 Series Manuale utente

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuale utente

Sparkrite

Sparkrite SRA8 Manuale utente

Viper

Viper 4708V Manuale utente

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuale

Falcon

Falcon Predator XL3 Guida utente

Audiovox

Audiovox Auto Security XR91 Istruzioni operative

Clifford

Clifford Sabre II Manuale utente

CrimeStopper

CrimeStopper CS-8717 Guida rapida

Ultra Start

Ultra Start 450 SERIES Manuale utente

Scytek electronic

Scytek electronic Vectra X3 Manuale utente

Excalibur

Excalibur AL-1860-EDPB Manuale utente

Clifford

Clifford CYBER 2 Manuale utente

Gemini

Gemini 7057 Manuale utente

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuale utente

Magicar

Magicar FAI-440 Manuale utente