Cooper Security Scantronic i-gsm02 Guida all'installazione

i-gsm02

GSM Module

Installation and

Programming Guide

Page 2

Introduction .......................................................................... 3

Installation............................................................................ 3

Preparation......................................................................... 3

Choosing a network account............................................... 3

Siting the antenna ............................................................ 4

Checking network signal strength........................................ 4

Dealing with poor signal strength ........................................ 5

Fitting the Module................................................................ 6

Registering a SIM Card......................................................... 7

Using Top Up Cards..........................................................10

Other Programming ............................................................10

Recording Voice Messages ...................................................11

Finishing the Physical Installation..........................................11

Every effort has been made to ensure that the contents of this book are correct. However,

neither the authors nor Cooper Security Limited accept any liability for loss or damage caused

or alleged to be caused directly or indirectly by this book. The contents of this book are subject

to change without notice.

Printed and published in the U.K.

This manual applies to software used in the i-on40 control unit with version 2.xx.xx software.

i-gsm02

Page 3

Introduction

The i-gsm02 module is designed to fit on the i-on40 control unit.

The i-gsm02 allows the control unit to report alarms over the

mobile telephone network using either recorded speech messages,

or SMS (Short Message Service) texts. The

Figure 1 shows the main features of the module.

1 2 3 4

Top Bottom

1. Speaker 3. Sim card holder

2. Microphone 4. Connector pins

5. Aerial socket

Figure 1. i-gsm02 Module

Installation

Preparation

Before installing the i-gsm02, please consider the type of network

account and the physical location of the unit and its antenna.

Choosing a network account

Avoid using a pay as you go account. If you must, then be aware

that the i-gsm02 cannot warn you of low credit. Set up regular top-

ups for the account or manage it through the internet (if the

provider gives you that option).

Note: This module is not currently compatible with 3G sim cards.

i-gsm02

Page 4

Siting the antenna

Before installing the unit you must decide on a suitable location for

the antenna. Site the antenna so that it can receive a good signal

from the phone network. Note that the supplied antenna lead is 3m

long.

Place the antenna:

As high as possible.

As far away from the control unit as possible.

At least 1 metre from any metalwork (pipes, cabinets, cabling,

cement reinforcing bars, metallic coated glass).

Vertically (see Figure 2).

So that the lead runs horizontally from the antenna for at least

250mm.

250mm

2,000 mm

No metal within

this area.

2,000 mm

Figure 2. Aerial Positioning

Checking network signal strength

There are three ways to check the network signal strength at your

installation:

1. Use the i-gsm02. You can temporarily fit the SIM card and

antenna to the i-gsm02 and fit the i-gsm02 module to the i-on40.

Caution: Follow the instructions in “Fitting the Module” on page .

You can then register the SIM card (see page 7). However, you

should be aware that unless the SIM is registered, the i-on40 will

report the strength of the strongest network signal. This may be an

emergency network. (In the UK, all networks must provide access

i-gsm02

Page 5

to any mobile phone for emergency calls.) Check that the i-gsm02

SIM is registered before checking the signal strength.

Caution: If you must remove the i-gsm02 module: a) remove all

power from the control unit, both mains and battery, b) take care

not to bend the pins.

2. You can use your mobile phone, provided that it is registered

with the same network as the SIM (Subscriber Identity Module)

card that you intend to fit to the i-gsm02. If your phone reports at

least two bars of signal at the site of the i-gsm02 antenna then the

i-gsm02 should be able to work on that network.

NOTE: When testing the signal strength you must hold your phone

in the exact location of the i-gsm02 antenna.

If you decide that a location has a good signal, then you must fit

the centre rib of the i-gsm02 antenna within 20mm of the spot

occupied by your phone. (The signal wavelength is so short, that

moving 80mm can change the signal strength markedly. This may

not matter with a strong signal, but with a weak signal it could

mean that the i-gsm02 will not register.)

3. If your phone does not work on the same network as the SIM

you intend to install in the i-gsm02, then, provided your phone is

not locked, you can put the i-gsm02 SIM in your phone, and test

for network signal strength as described in step 1. Ensure that you

can make a call from the chosen position, it is not enough to rely

on the signal strength indication.

Once you have completed testing you must remember to shut down

your phone in the recommended manner before extracting the i-

gsm02 SIM. If you remove power abruptly (for example by taking

the phone battery out) the SIM card may not have time to de-

SIM for several hours.

Note: Do not lock the SIM card with a PIN (the i-gsm02 will not let

you key in a PIN for the card).

Dealing with poor signal strength

If the signal strength is poor, either:

Find a better antenna position.

Change the network provider.

i-gsm02

Page 6

Fitting the Module

Note: Do not fit the i-gsm02 OR its antenna until you have

confirmed that there is adequate network signal strength.

1. Remove mains power from the i-on40 end station.

2. Caution: Open the end station lid and disconnect the battery.

3. Pass the plug end of the antenna lead from outside the end

station case through one of the cable entry holes into the

interior and connect the antenna lead plug to the i-gsm02 (see

Figure 3).

Figure 3. Connect the Aerial

4. Fit the SIM card (see Figure 4). Ensure that you fit the SIM card

in the correct orientation.

Figure 4. Fit a SIM Card

i-gsm02

Page 7

5. Fit the i-gsm02 to the plug on module sockets (see Figure 5). Take

care not to unseat the antenna lead connector. Do not use excessive

force when seating the module.

Figure 5. Fitting i-gsm02 Module

6. Using the supplied surface wipe, clean the area onto which you

intend to stick the antenna. Remove the backing paper on the

glued side of the antenna. Fix the antenna onto the cleaned

surface. Note: The adhesive on the antenna is fast acting. You

will not be able to reposition the antenna once you have put it

in place.

7. Reconnect the battery. (The control unit will not start.)

Registering a SIM Card

Once you have fitted the i-gsm02 module and its SIM card, you

must register the SIM card with the service provider. To do this you

must make a telephone call from the i-on40 control unit via the

newly installed i-gsm02 module.

7. Apply mains power to the i-on40 unit.

8. From standby, enter the Installer code, then use the scroll keys

(uor n) to display the Test menu:

Press Yto select. The screen will show the first option: Test

Messages.

i-gsm02

Page 8

9. Press uor press nto show:

GSM Phone Utils.

10. Press Yto select. The screen will show the first option: Make

Call.

11. Use the scroll keys (uor n) and then Y, to select the following

options:

Make Call Allows you to enter a number and make a call via

the GSM link. The i-on40 will act like a hands

free mobile phone. You can use the * and # keys

as you would on a normal phone.

Signal Strength If the level is low you may need to reposition the

control unit, or seek another service provider.

GSM Number (This may not appear if you are using Vodafone

as a service provider.) Note this number down so

that you can supply it when registering your SIM

card.

IMEI Number You should note this number down as you will

need to provide it when you register your SIM

card with certain service providers.

12. Select the Make Call option.

13. Dial the appropriate telephone number for registering the SIM

card as shown in the instruction leaflets for the card.

Note that the i-on40 cannot support the text message response

service calls using the * and # keys. You must call the service

provider manually and either register with a human operator, or

navigate an automated answering service. Once the phone call is

established you can use the * and # keys as you would on a normal

phone.

If the control unit is having difficulty registering, the keypad display

may show one of the following error codes:

"Not Reg." Not registered, gsm module is not searching for a

new operator

"Reg. Home" Registered, home network ("Reg. Home" gets

replaced with operator name when available)

i-gsm02

Page 9

"Searching..." Not registered, gsm module is searching for a new

operator

"Reg.

Denied" Registration denied

"Reg.

Unknown" Unknown

"Reg. Roam" Registered, roaming ("Reg. Roam" gets replaced

with '*' and operator name when available)

The exact details of registering your SIM card differ for each

provider.

Note that 02 print the SIM serial number and the GSM telephone

number on the packing for the SIM card.

To register an 02 SIM dial 248 and follow the instructions given by

the automatic answering service.

T-Mobile

T-Mobile print the GSM telephone number, PIN number and PUK

(unlock number) on the sheet carrying the SIM card and top up

card.

To register a T-Mobile SIM dial 150 and follow the instructions given

by the automatic answering service.

If you have several mobile phones fix the sticky label provided

showing the GSM number to the top up card.

Orange

Make sure you have the GSM module’s IMEI number to hand. You

will also need the SIM card serial number which is printed on the

SIM card.

You will need to provide a password and the four digit code to

identify yourself in the future. Choose them before making the call

and write them down in the booklet.

To register an Orange SIM dial 0800 079 0006. A human operator

will reply.

While registering your SIM, the operator will provide you with your

GSM number. Make sure you note this number on the top up card.

i-gsm02

Page 10

Vodafone

To register a Vodafone SIM dial 2345 and follow the instructions

given by the automatic answering service. During the instructions

you will be given your GSM number. Make sure that you note this

number down on the back of the top up card.

Using Top Up Cards

Avoid using a pay as you go account. If you must, then be aware

that the i-gsm02 cannot warn you of low credit. Set up regular top-

ups for the account or manage it through the internet (if the

provider gives you that option).

Various service providers supply top up cards with their SIMs. Part

of the registration procedure is to link the top up card with the SIM.

The cards contain just enough credit to allow you to make the

registration call. Once you have finished this process you will need

to supply more credit to the top up card. You should do this

immediately.

While registering, make sure that you write the phone number of

the GSM module down on the top up card.

The table below provides spaces for you record the relevant

information about your GSM installation.

IMEI No.

SIM Card Serial No.

GSM No.

Top Up Card No.

Other Programming

For details on programming the i-gsm02 please refer to the

i-on40 Programming Reference. All the options necessary for

programming the module are in the Installer Menu under the

Communications option.

Note: The control unit hides the Communications – Speech Dialler

and Communications – ARC Reporting options if there is no i-

gsm02 fitted.

Indice

Altri manuali Cooper Security Unità di controllo

Cooper Security

Cooper Security Scantronic 9752 Manuale utente

Cooper Security

Cooper Security Scantronic 9751 Manuale utente

Cooper Security

Cooper Security SD3 Manuale utente

Cooper Security

Cooper Security M-Series Manuale utente

Cooper Security

Cooper Security i-On 40 Manuale utente

Cooper Security

Cooper Security i-on Series Manuale utente

Cooper Security

Cooper Security Scantronic 9853 Istruzioni generali

Cooper Security

Cooper Security M800 Guida utente

Cooper Security

Cooper Security Scantronic i-sd02 Guida all'installazione

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente