Crestron CNWMBG2-34A Manuale utente

CRESTRON CNWMBG2-34A Wall-Mount Wired Panel

REMOTE CONTROL SYSTEMS

1 DOC. 8002B

Specifications subject to change without notice.

1 2 3

UP1 UP2

DOWN1 DOWN2

BAR 2BAR 1

100

CRESTRON

4.63 in

11.76 cm

4.63 in

11.76 cm

Panel installs in 4-gang electrical box (1.60 in (4.06 cm) minimum depth).

SYNTAX:

NET.ID <10 to FE>: CNWP

i1,o1 = <signal name> \ button and LED combined

i2 = <signal name> \ independent button

o2 = <signal name> \ independent LED

" = " "

i30 = <signal name>

o30 = <signal name>

BAR1 = <signal name> \ left bargraph

UP1 = <signal name> \ left volume up button

DOWN1 = <signal name> \ left volume down button

BAR2 = <signal name> \ right bargraph

UP2 = <signal name> \ right volume up button

DOWN2 = <signal name> \ right volume down button

DESCRIPTION:

The CNWMBG2-34A wired panel interfaces to a CRESNET II control system over the CRESNET II network. The panel uses

30miniature pushbuttonswith self-containedfeedback LEDs.Two bargraphindicatorsare included.Each bargraphhas two

miniature pushbuttons. The CNWMBG2-34A is designed for wall-mounting using a standard four-gang electrical box.

Custompanel finishes,engraving,colored buttoncaps, andtheomission ofunusedbuttons areall standard.

CRESTRON CNWMBG2-34A Wall-Mount Wired Panel

REMOTE CONTROL SYSTEMS

2 DOC. 8002B

Specifications subject to change without notice.

Eachunique panel or component on the CRESNET II network requires the setting of an identity code (ID CODE).ID CODES are

two-digithexadecimal numbers, from 10 toFE. The ID CODE ofthe panel should be set tomatch the ID CODE specifiedin the

NET.IDstatement of the CRESNET II SIMPL-C program referencing the panel (refer to syntax section). To set an ID CODE,

removethe panel fromthe electrical box anddisconnect power.

Accessible through the back plate are two miniature circuit-mounted rotary switches, identified as H and L. These 16-

position hexadecimal switches can be set to 0 through F. Using a small screwdriver, rotate the arrow in the center of the

switch marked H to point to the first (or most-significant) digit or letter of the specified ID CODE. Set the switch marked L to

the second (least-significant) digit or letter of the specified ID CODE.

The 4-pin connector marked NET should be wired to the CRESNET II network. Network termination points are available at

the control system power supply. Network units may also be daisy-chained together. Refer to the latest revision of the

CRESNET II reference manual section on CNPWS power supplies (Doc 8017 or Doc. 8091) for wire gauge specifications and

connectiondetails.

Thepanel drawing on the previous page showsthe location of the SIMPL-C button numbersand their corresponding button

positions.Buttons or bargraphs which arenot used need not beassigned a signal name.

REQUIRES:

CRESNET II Workshop Version 4.00 or later.

CRESNET II Operating System SR30160.OPS or later.

FURTHER INQUIRIES:

If after reviewing this information you still have additional questions, please contact a CRESTRON technical support

representative by dialing (888) CRESTRON [(888) 273-7876] or (201) 894-0660.

Indice

Altri manuali Crestron Rack e supporto

Crestron

Crestron RMK-4000L Manuale utente

Crestron

Crestron TMK-4L Manuale utente

Crestron

Crestron TST-600-DSW-PMK Manuale utente

Crestron

Crestron TSW-560 Manuale utente

Crestron

Crestron CCS-TS-6500-MCK Manuale utente

Crestron

Crestron TMK-15L Manuale utente

Crestron

Crestron MMK-15L Manuale utente

Crestron

Crestron TMK-3100L Manuale utente

Crestron

Crestron TPS-6X-DSW Manuale utente

Crestron

Crestron RMK-15L Manuale utente

Crestron

Crestron RMK-8L Manuale utente

Crestron

Crestron TST-902-DSW Disegno dimensionale

Crestron

Crestron RMK-9L Manuale utente

Crestron

Crestron TSW-770-MSMK-ANG Manuale utente

Crestron

Crestron MK-IM-RX Manuale utente

Crestron

Crestron TMK-12L Manuale utente

Crestron

Crestron MMK-1000L Manuale utente

Crestron

Crestron HBK-6000 Manuale utente

Crestron

Crestron MP-WP-2XLRO-1G Manuale utente

Crestron

Crestron CAEN-CK Manuale utente

Crestron

Crestron MPC3-101-RMB Manuale utente

Crestron

Crestron PMK-1000L Manuale utente

Crestron

Crestron CCS-UC-200-WSTND Manuale utente

Crestron

Crestron TSS-752-MSMK Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente