Cross Technologies 2005 Manuale utente

Instruction Manual

Model 2005-10-01

Upconverter

October 2013, Rev. A

DC ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST CONVERTER

CKU

70 140

IF FREQUENCY

GHz 1MHz10MHz100MHz

CROSS TECHNOLOGIES, INC.

DC POWER

J1 J3 J2

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB: www.crosstechnologies.com

E-MAIL: [email protected]

INSTRUCTION MANUAL

MODEL 2005-10-01 Upconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Front Panel Controls/Indicators 5

2.3 Rear Panel Input/Output Signals 5

2.4 Accessing the PC Card 6

2.5 Installation/Operation 6

3.0 Environmental Use Information 5

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies,

Inc.’s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies,

Inc. shall not be liable for any special, indirect, or consequential damages. This warranty

does not cover parts or equipment which have been subject to misuse, negligence, or

accident by the customer during use. All shipping costs for warranty repairs will be

prepaid by the customer. There are not other warranties, express or implied, except as

stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2005-10-01 Manual, Rev. A Page 2 10/30/2013

MODEL 2005-10-01 Upconverter

1.0 General

1.1 Equipment Description

The 2005-10-01 Test Upconverter for loop-back applications converts a 70 MHz or 140 MHz IF signal

to 2000 to 2500 MHz in 1 MHz steps with selection of high side LO (C = inverted) or low side LO

(Ku = non-inverted) and 70 or 140 MHz input over the 2.0 - 2.5 GHz range. The 2005-10-01 allows for

an input level range of +10 to -15 dBm.

Featuring low phase noise, these units are used to loop 70 or 140 MHz modulators to 2.0 - 2.5 GHz receivers

for test purposes and the output consists of the LO and both upper and lower sidebands. The 70 or 140 MHz

carrier input is mixed with a synthesized local oscillator (LO) signal. The output frequency is selected and

indicated by the four BCD switches which control the synthesized LO. Front panel LEDs light when DC

power is applied (green) and when a PLL alarm occurs (red). The mixer output is applied to the output

amplifier providing a nominal gain of -10 dB. Connectors are 50ΩBNC (female) for the IF input and for

the RF output (other connector options are available). Powered by a 120 VAC wall power supply (100-240

±10%VAC, option -P4). The 2005 can be mounted on a 1 3/4” X 19 “ rack mount panel (option -R).

2000

2500

MHz OUT

140

MHZ IN

1860

2640

MHz

2. 338

CONTROLLER

Block Diagram

ATTEN

FIGURE 1.1 Block Diagram

DC ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST CONVERTER

CKU

70 140

IF FREQUENCY

GHz 1MHz10MHz100MHz

CROSS TECHNOLOGIES, INC.

DC POWER

J1 J3 J2

FIGURE 1.2 Front and Rear Panel

2005-10-01 Manual, Rev. A Page 3 10/30/2013

1.2 Technical Characteristics

TABLE 1.0 2005-10-01 Upconverter Specifications*

Input Characteristics

Impedance 50Ω

Return Loss 15 dB

Frequency 70 or 140 MHz center, ±20 MHz

Level +10 to -15 dBm

1dB compression +15 dBm

Output Characteristics

Impedance 50Ω

Return Loss 12 dB

Frequency Range 2.0 to 2.5 GHz

Channel Characteristics

Gain -10 dB ± 3 dB

Spurious Response <-40dBC max, < -45dBC typ for Fc ±20MHz;

OUTPUT NOT FILTERED, Lo<=RF nominal

Frequency Response ± 2 dB, 2.0 - 2.5 GHz; ± 0.5 dB, any 10MHz increment

Synthesizer Characteristics

Frequency Accuracy ± 25 kHz max; Option -HT for ±0.1ppm Internal Reference

Frequency Step 1.0 MHz minimum

-100-90-80-70-70

1MHz100kHz10kHz1kHz100 MHz

dBC/Hz

Phase Noise

Fre

Indicators

DC Power Green LED

PLL Alarm Red LED

Other

RF, IF Connectors 50ΩBNC (RF), 50ΩBNC (IF)

Size, Bench Top 4.7” Wide X 1.75” High X 6.5” Deep

Size, Rack Mount 19 inch standard chassis 1.75”High X 7.0” Deep (option -R)

Power, standard 120 ± 10% VAC, 60 Hz, 10W max wall mount power supply

AC Power 100-240 ±10% VAC, 47-63 Hz, wall mount power supply (option -P4)

*+10 to +40 degrees C; Specifications subject to change without notice

2005-10-01 Manual, Rev. A Page 4 10/30/2013

2.0 Installation

2.1 Mechanical

The 2005-10-01 is packaged in an aluminum extrusion. The -R option is mounted on a 1 3/4” X 19” panel

that can be mounted to a rack using the 4 holes at the ends. The unit derives +DC from the wall power supply

(+15V unregulated, or regulated universal -P4). See Figure 2.3.

2.1.1 Cleaning Instructions

Wipe the exterior with a dry, soft cloth. Use no detergent or cleaning chemicals.

2.2 Front Panel Controls/Indicators - Fig. 2.1 shows front panel controls and indicators for the 2005-10-01.

SW6 - LO SELECT

Slide switch selects high side (C)

or low side (Ku) local oscillator.

DS1 - POWER LED

Lights green when DC

power is present

SW1 to SW4 - FREQUENCY BCD SWITCHES

Select the desired output frequency which is the LO

frequency - 70, -140, +70, or +140 MHz in GHz.

DS2 - ALARM LED

Lights red when PLL

comes out of lock

SW5 - IF SWITCH

Slide switch selects 70 or 140 MHz IF In

DC ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST UPCONVERTER

CKU

70 140

IF FREQUENCY

GHz 1MHz10MHz100MHz

FIGURE 2.1 2005-10-01 Front Panel Controls and Indicators

2.3 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output signals to the 2005-10-01.

J1 - IF INPUT

70 or 140 MHz input.

+10 dBm max level

BNC (female)

50Ωconnector.

(Option -SS, 50ΩSMA)

J3 - DC POWER

The unregulated DC voltage from the

wall power supply (option P, P4).

15 VDC, 200 ma.

J2 - RF OUT

Output selected and

indicated by four

BCD switches.

BNC (female)

50Ωconnector.

(Option -SS, 50ΩSMA)

+15GND

CROSS TECHNOLOGIES, INC.

DC POWER RF

J1 J3 J2

FIGURE 2.2 2005-10-01 Rear Panel Inputs and Outputs

2005-10-01 Manual, Rev. A Page 5 10/30/2013

2.4 Accessing the PC Card

There are NO USER JUMPERS or other on-card controls. ALTHOUGH IT IS NOT RECOMMENDED AND

MAY VOID THE WARRANTY the following shows how to remove the printed circuit board (PCB) from the

extrusion:

1. ALWAYS REMOVE POWER when installing or removing the PCB from the extrusion

2. Remove four (4) rear panel screws (see Figure 2.3).

3. GENTLY pull the rear panel and PCB assembly completely out of the extrusion.

4. To install the PCB, GENTLY push the rear panel and PCB assembly completely into the extrusion

Make sure the shield goes in the lower channel and the PCB in the next channel above that in the

extrusion and that the front panel controls go through the front panel holes.

5. Install four (4) rear panel screws.

EXTRUSION

FRONT SCREWS (4EA)

FRONT PANEL

RACK MOUNT PANEL (FOR -R MODELS ONLY)

REAR SCREWS (4EA)

PCB

ASSEMBLY

REAR PANEL

WALL

POWER

SUPPLY

(-P and -P4 ONLY)

2005 TEST CONVERTER

CROSS TECHNOLOGIES, INC.

100MHz

FREQUENCY

10MHz 1MHzGHz

LO IF

CKU 70140

ALARM

FIGURE 2.3 2005 Assembly Drawing

2.5 Installation / Operation

2.5.1 Installing and Operating the 2005-10-01

1. If using the receiver LNB voltage to power the 2005-10-01, be sure +14 to +24 VDC is on the RF

center conductor. If using the wall power supply (options -P or -P4), connect the power supply to

the DC POWER connector and either 120 ±10% (-P) or 100-240 ±10% VAC (-P4) (Figure 2.2)

2. Select either C or KU band (SW6) and either 70 or 140 MHz IF (SW5) using the

front panel switches (Figure 2.1).

3. Connect a +10dBm max signal to IF In, J1 (Figure 2.2).

4. Connect the RF OUT, J2, to the receiver under test (Figure 2.2).

5. Set BCD switches, SW1 to SW4, to the desired frequency (Figure 2.1).

6. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.1).

2005-10-01 Manual, Rev. A Page 6 10/30/2013

3.0 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connection to the

Branch (use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2005-10-01 Manual, Rev. A Page 7 10/30/2013

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB: www.crosstechnologies.com

E-MAIL: [email protected]

Printed in USA

2005-10-01 Manual, Rev. A Page 8 10/30/2013

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cross Technologies Convertitore multimediale

Cross Technologies

Cross Technologies 2115-275-1845 Manuale utente

Cross Technologies

Cross Technologies 2016-75-213 Manuale utente

Cross Technologies

Cross Technologies 4115-300 Manuale utente

Cross Technologies

Cross Technologies 2005-02P4 Manuale utente

Cross Technologies

Cross Technologies 2116-140T120 Manuale utente

Cross Technologies

Cross Technologies 2416 25 Series Manuale utente

Cross Technologies

Cross Technologies 2117-7172 Manuale utente

Cross Technologies

Cross Technologies 2116-21-1014 Manuale utente

Cross Technologies

Cross Technologies 3116-145-1600 Manuale utente

Cross Technologies

Cross Technologies 2415-02 Series Manuale utente

Cross Technologies

Cross Technologies 4117-14 Manuale utente

Cross Technologies

Cross Technologies 2017-0923 370 Series Manuale utente

Cross Technologies

Cross Technologies 2116-300-1600 Manuale utente

Cross Technologies

Cross Technologies 2017-03 Manuale utente

Cross Technologies

Cross Technologies 2015-03A Manuale utente

Cross Technologies

Cross Technologies 2016-02-1200 Manuale utente

Cross Technologies

Cross Technologies 4115-41-212 Manuale utente

Cross Technologies

Cross Technologies 2016-1522 Manuale utente

Cross Technologies

Cross Technologies 2016-8085 Manuale utente

Cross Technologies

Cross Technologies 2015-26 Manuale utente

Cross Technologies

Cross Technologies 2116-182193 Manuale utente

Cross Technologies

Cross Technologies 2416 02I Series Manuale utente

Cross Technologies

Cross Technologies 2016-57 Manuale utente

Cross Technologies

Cross Technologies 2015-58T Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente