Cross Technologies 2117-9395 Manuale utente

Instruction Manual

Model 2117-9395

Up/Downconverter

September 2019, Rev. 0

MODEL 2117

CROSS TECHNOLOGIES INC.

EXT

10MHZ POWERALARM

UP/DOWNCONVERTER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2117-9395 Up/Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Front & Rear Inputs and Outputs 6

2.3 Available Options/Pinouts 7

2.4 Installation/Operation 8

2.5 Use Information 9

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2117-9395_Manual Page 2 09/12/19

MODEL 2117-9395 Up/Downconverter

9.30-9.50 GHz Up, 9.30-9.50 GHz Down

1.0 General

The 2117-9395 Up/Downconverter converts 2.00 - 2.20 GHz to 9.30 - 9.50 GHz and 9.30-9.50 GHz to 1.60 -

1.80 GHz, with non-inverting spectrums. Front panel LEDs provide indication of DC Power, External 10 MHz,

and PLL Alarm. The gain is +20 dB for the upconverter and -20 dB for the downconverter. Connectors are

Type N female for the RF output and input, BNC female for the L-band input and output and external reference

input and reference output. A three-way switch controls which 10 MHz reference is being used. In the AUTO

position, the internal reference is used unless a +3 dBm ± 3 dB, 10MHz reference signal is connected to the

external reference input. The 2117 is powered by a 100-240 ± 10% VAC power supply, and in a 1 3/4” X 19” X

19” rack mount chassis.

MODEL 2117

CROSS TECHNOLOGIES INC.

EXT

10MHZ POWERALARM

UP/DOWNCONVERTER

FRONT PANEL

GND

EXT REF

IN REF

OUT

INT EXTAUTO

S1 J112

J11

MONITOR

AND

CONTROL

15 23

J111

RF2 IN

RF2 OUT

J102J101

RF1 OUT

RF1 IN

DOWNCON UPCONV

REAR PANEL

FIGURE 1.1 Model 2117-9395 Front and Rear Panels

2117-9395

Up/Dowconverter

Block Diagram

10 MHz

To PLLs

EXT 10 M

10 M

MON

2.00 to 2.20

GHz IN

RF2 In

9.30 to 9.50 GHz BP 2.20 GHz LP

9.30 to 9.50

GHz OUT

RF2 Out

7.30 GHz

9.30 to 9.50

GHz IN

RF1 In

1.60 to 1.80

GHz OUT

RF1 Out

9.30 to 9.50 GHz BP

7.70 GHz

1.80 GHz LP

Upconverter

Dowconverter

ATT. ATT.

FIGURE 1.2 Model 2117-9395 Up/Downconverter Block Diagram

2117-9395_Manual Page 3 09/12/19

1.2 Technical Characteristics

TABLE 1.0 2117-9395 Up/Downconverter Specifications*

EQUIPMENT SPECIFICATIONS*

SPECIFICATIONS*

IInput

Input Characteristics

UP, C

DOWN, C

Impedance/Return Loss 50Ω/14 dB 50Ω/14 dB

Frequency 2.00-2.20 GHz 9.30-9.50 GHz

Noise Figure, Max. 20 dB @ max gain 25 dB @ max gain

Input Level range -40 to -20 dBm -20 to 0 dBm

OOutput

Output Characteristics

Impedance/Return Loss 50 Ω/14 dB 50 Ω/14 dB

Frequency (GHz) 9.30-9.50 GHz 1.60-1.80 GHz

Output Level Range -20 to 0 dBm -40 to -20 dBm

1 dB comp, max gain

+10 dBm -10 dBm

Mute @ 0 dBm out

>50 dB

N/A

CChannel

Channel Characteristics

Gain, max. at Fc, fixed

+20 ±2 dB -

-20 ±2 dB

Image Rejection >

>60 dBC

Spurious, Inband, sig. rel. <

<-50 dBC, 0dBm

<-50 dBC, -5dBm

Spurious, Inband, sig. ind. <

<-50 dBC, Gmax

Spurious, Out of band

<-50 dBm, Gmax <-50 dBm, Gmax

2 tone 4MHz; Max -10 ea

<-50 dBC,Gmax <-50 dBC,Gmax

Frequency Resp. band

±1.5 dB

Frequency Resp. 85 MHz

± 0.75 dB

Frequency Sense n

non-inverting

LO Characteristics

LO Frequency Downconverter -7.70 GHz; Upconverter - 7.30 GHz

Frequency Accuracy ± 0.01 ppm max over temp internal reference; external reference input

10 MHz Level +3 dBm, ± 3dB, 75 ohms, External In or Internal out

-110-100-85-80-70

1MHz100kHz10kHz1kHz100

MHz

dBC/Hz

Phase

Noise

Fre

q (

)

Controls, Indicators

INT/AUTO/EXT Switch Selects internal or external 10 Mhz 9 (rear panel DP3T switch)

Ext 10 MHz Yellow LED, indicates external 10 MHz reference selected

PLL Alarm Red LED, External contact closures

Power Green LED

Other RF1 In, RF2 Out N-type (female), 50Ω

RF1 Out, RF2 In BNC (female), 50Ω

10 MHz connectors BNC (female), 75Ωconnector; works with 50Ωor 75Ω

Alarm Connector DB9 - NO or NC contact closure on Alarm

Size 19 inch standard chassis 1.75” high X 14” deep

Power 100-240 ± 10% VAC, 47 - 63 Hz, 50 watts maximum

Options

Connector Options See TABLE 2.2

*+10˚C to +40˚C; Specifications subject to change without notice.

2117-9395_Manual Page 4 09/12/19

2.0 Installation

2.1 Mechanical - The 2117-9395 consists of one RF PCB housed in a 1 RU (1 3/4 inch high) by 14 inch deep

chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2117-9395 can

be secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2117-9395 is assembled.

PS IN

PIN 1, +12 VDC

PIN 2, +5 VDC

PIN 3, +5 VDC

PIN 4, GROUND

PIN 5, GROUND

PIN 6, -12 VDC

PIN 7, +24 VDC

PIN 8, +24 VDC

POWER

SUPPLY

FIGURE 2.0 2117-9395 Mechanical Assembly

2117-9395_Manual Page 5 09/12/19

2.2 Rear Panel Input/Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.

INT AUTO EXT

GND

J102

AND

MONITOR

CONTROL

J2 - EXT 10 MHz INPUT

BNC (Female), 75Ωinsert

external 10 MHz reference

here

(

dBm

± 3 dB)

J11 - ALARM

DB9 (Female)

connector.

See table 2.1

5 23

J8-10 MHz OUTPUT

BNC (Female), 75Ω

J101

1.6 to 1.8 GHZ IN

BNC Type Female 50Ω

-40

-20

dBM

J102

9.3 to 9.5 GHZ IN

N-Type Female 50Ω

-20

dBM

J112

9.30 to 9.50 GHz OUT

N-type Female 50Ω

-20

dBM

S1 - 10MHz SWITCH

3 position switch INT selects 10MHz

ref. Auto selects internal10MHZ ref.

unless a 0 dBm ± 3 dB 10 MHz

signal is inserted on J2 EXT selects

external

10MHz

reference

from

J2.

J2 J101 J111 UPCON

J112

J111

2.00 - 2.20 IN

BNC

-40

-20

RF2 IN

RF2 OUT

J11

RF1 IN

DOWNCON

J102

RF2 OUT

RF1 OUT

EXT REF

IN RF

OUT

AC INPUT

100-240 VAC, 47-60 Hz

Uses 2 amp Slow Blo,

5mm

fuse.

Shown below (Option P48) - Rear Panel Input/Output Signals

with Option P48, 48 VDC nominal 36-72 VDC, 2.5A maximum.

INT AUTO EXT

GND

J102

AND

MONITOR

CONTROL

5 23

36 TO 72 VDC

• •

•

DC INPUT

J2 J101 J111 UPCON

J112

RF2 IN

RF2 OUT

J11

RF1 IN

DOWNCON

J102

RF2 OUT

RF1 OUT

EXT REF

IN RF

OUT

DS2 - ALARM LED

Lights RED when PLL

comes out of lock.

DS1 - POWER LED A

Lights GREEN when DC voltage is

present from AC power supply.

DS3 - EXT 10MHZ LED

Lights YELLOW when external

10MHz reference is active.

POWER

EXT

10MHZ ALARM

FIGURE 2.2 2117-9395 Front Panel Controls and Indicators

2117-9395_Manual Page 6 09/12/19

TABLE 2.1 J111

TABLE 2.1 J11 Pinouts (DB9)

Pin Function

1 Not Used

2 Not Used

3 Not Used

4 Not Used

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

TABLE 2.3

DC1

TABLE 2.3 DC1 Pinouts

Pin# Function

1 Minus DC input

2NC

3 Plus DC input

4NC

Shell Ground

FIGURE 2.1 2117-9395 Rear Panel I/Oʼs FIGURE 2.3 2117-9395 DC1 Pinouts

TABLE 2.2 Available Options

P48 = 48 VDC Nominal 36-72 VDC, 2.5A max.

R = Redundant AC Power Supply

Available Connector Options

NF 50ΩN-Type (RF), 75ΩF-Type (L-Band)

N50ΩN-Type (RF), 75ΩBNC (L-Band)

NN 50ΩN-Type (RF), 50ΩN-Type (L-Band)

SS 50ΩSMA (RF), 50ΩSMA (L-Band)

FIGURE 2.2 2117-9395 Available Options

2117-9395_Manual Page 7 09/12/19

2.4 Installation / Operation

2.4.2 Installing and Operating the 2117-9395 Downconverter

1.) Connect a -20 dBm to 0 dBm from 9.30 - 9.50 GHz, signal to RF INPUT, J102 (Figure 2.1).

2.) Connect the L-BAND OUTPUT, RF1 OUT, J101 to the external equipment.

Output will be 1.60 - 1.80 GHz.

3.) Connect 100-240 ± 10% VAC, 47 - 63 Hz to AC connector on the back panel.

4.) Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).

5.) Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS a external

10MHz, 0 dBm signal is connected to J2), or EXT (for external 10MHz, 0 dBm ref that is inserted

at J2) on rear panel switch S1 (Figure 2.1).

6.) If EXT is selected or AUTO is selected and there is a 10MHz, 0 dBm signal at J2, check that DS3

(yellow, Ext 10 MHz) is on (Figure 2.2).

7.) Check that a 10MHz, 0 dBm ±3 dB signal is present at the 10 MHz REF OUTPUT (J8)

(Figure 2.1).

8.) AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot

in the drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot.

If a fuse continues to open, the power supply is most likely defective.

2.4.3 Installing and Operating the 2117-9395 Upconverter

1. Connect a -40 dBm to -20 dBm signal, from 2.0 to 2.2 GHz,

to L-BAND INPUT, RF2 IN, J111 (Figure 2.1).

2. Connect the RF OUTPUT, J112, to the external equipment.

Output will be 9.3 to 9.5 GHz.

3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.

4. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).

5. Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS a external 10MHz,

3 dBm signal is connected to J2), or EXT (for external 10MHz, 3 dBm ref that is inserted at J2) on rear

panel switch S1 (Figure 2.1).

6. If EXT is selected or AUTO is selected and there is a 10MHz, 3 dBm signal at J2, check that DS3

(yellow, Ext 10MHZ) is on (Figure 2.2).

7. Check that a 10MHz, 3 dBm ±3 dB signal is present at the 10MHZ REF OUTPUT (J8) (Figure 2.1).

8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the

drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a fuse

continues to open, the power supply is most likely defective.

2117-9395_Manual Page 8 09/12/19

AC Fuse - 2 amp slow blow (Type T),

5 mm X 20 mm

FUSE DRAWER

SPARE FUSE

INPUT

100-240± 10%VAC

47-63 Hz

2A MAX

FUSE

TYPE T 2A GDC

250 VOLT

FOR 100 - 240 V~

FIGURE 2.3 Fuse Location and Spare Fuse

2117-9395_Manual Page 9 09/12/19

Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra. (Maximum Recommended Ambient Temperature)

D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between units

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connection to the

Branch (use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2117-9395_Manual Page 10 09/12/19

Altri manuali Cross Technologies Convertitore multimediale

Cross Technologies

Cross Technologies 2099-10 Manuale utente

Cross Technologies

Cross Technologies 2115-275-1845 Manuale utente

Cross Technologies

Cross Technologies 2017-03 Manuale utente

Cross Technologies

Cross Technologies 2016-25-01 Manuale utente

Cross Technologies

Cross Technologies 2016-75-213 Manuale utente

Cross Technologies

Cross Technologies 2415 0925 Series Manuale utente

Cross Technologies

Cross Technologies 2017-0923 370 Series Manuale utente

Cross Technologies

Cross Technologies 2117 Manuale utente

Cross Technologies

Cross Technologies 2015-24 Manuale utente

Cross Technologies

Cross Technologies 4115-41-212 Manuale utente

Cross Technologies

Cross Technologies 2415-x02 Manuale utente

Cross Technologies

Cross Technologies 2017-1727-140 Manuale utente

Cross Technologies

Cross Technologies 4116-31-2831 Manuale utente

Cross Technologies

Cross Technologies 4116-285-2450 Manuale utente

Cross Technologies

Cross Technologies 2009-2425-1750 Manuale utente

Cross Technologies

Cross Technologies 2016-12 Manuale utente

Cross Technologies

Cross Technologies 2015-03A Manuale utente

Cross Technologies

Cross Technologies 2005-10 Manuale utente

Cross Technologies

Cross Technologies 2016-26 Manuale utente

Cross Technologies

Cross Technologies 2415-02 Series Manuale utente

Cross Technologies

Cross Technologies 3115-21-109 Manuale utente

Cross Technologies

Cross Technologies 2016-57 Manuale utente

Cross Technologies

Cross Technologies 2015-05 Manuale utente

Cross Technologies

Cross Technologies 2115-122 Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente