Crosswater Elite Manuale utente

Elite water

control system

Operation and care guide

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

This operation and care guide

must be left with the user.

ELITEUSER

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Important Safety Information

Please read these instructions carefully before

using this system and keep in a safe place for

future reference.

To reduce the risk of electric shock and injury,

basic safety precautions, including the following,

should always be followed when using electrical

appliances.

Children MUST be supervised at all times when

using this shower control. Training should be

given to children and vulnerable individuals

before permitting them to operate the controls.

Do not pull on the power cable: this may

damage it and cause electric shock.

Never operate any appliance with a damaged

cable or plug. Do not use an appliance that

has been dropped or damaged or after any

malfunctions.

WARNING

CONTINUOUSLY TURNING THE

CONTROL WHEEL IN THE CLOCKWISE

DIRECTION MAY OVERRIDE THE PRE-

SET MAXIMUM TEMPERATURE, WITH

CONSEQUENT RISK OF SCALDING.

ALWAYS TAKE CARE WHEN

OPERATING THE CONTROL WHEEL,

AND DO NOT LEAVE CHILDREN

UNATTENDED WHILST THE PRODUCT

IS IN OPERATION.

Key to the display icons

Operating the Elite water control system

Setting the temperature

Setting the water ﬂow

Using the menu

Diverting the water ﬂow

Accessing the extended menu display

Setting the memory

(shower processor only)

Bath ﬁlling memory option

(bath processor only)

Cleaning (safe) mode

Opening and closing the pop up

bath waste (*using Viega electronic

waste ﬁller)

Self check mode

Thermal disinfection

Contents

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Extra features

Changing display from ﬂow

to temperature

Water consumption

Return

Setting maximum inlet temperature

Setting maximum run-time

(until automatic switch-o)

Change from Centigrade (Celsius)

to Fahrenheit

Statistics

Reset to factory settings

Cleaning / maintenance

Servicing / contact info

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Key to the display icons

Open / close bath drain

valve (Bath ﬁller waste only

available on bath processor)

Cleaning mode: disables the

control for 45 seconds

Set a new code

Backwards / return

Divert: Bath processor

Outlet 1: bath ﬁller icon

Outlet 2: hand shower icon

Outlet 3: ﬁxed head icon

Change display: ﬂow to

temperature - Display

switches automatically back to

temperature after 10 seconds

Save / delete current

pre-sets / quick access

(ﬂow, temperature, ﬁlling

bath stop level

Statistics

Self check: Diagnosis:

Inspection of control unit and

water supply

Setting maximum run-time

(until automatic switch-o)

Setting the maximum outlet

temperature

Change from Centigrade

(Celsius) to Fahrenheit

Reset to factory settings

Access and lock to extended

menu / features with a 3 digit

code

Shows the total amount

and last usage of water

consumption

Thermal disinfection

(emergency stop by pressing

control) Water will ﬂow at

maximum temperature for

5 minutes

Divert: Shower processor

Outlet 1: ﬁxed head icon

Outlet 2: hand shower icon

Outlet 3: body jet icon

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Operating the Elite water control system

Setting the temperature

Turn the control wheel

anti-clockwise, the control

will illuminate Blue, the

temperature is displayed and

the light will ﬂash until the set

temperature is reached.

Turn the control wheel until the

control illuminates Orange, the

temperature is displayed and

the light will ﬂash until the set

temperature is reached.

Cold Warm Hot

Press the control wheel once,

the control illuminates Orange

and water will start to ﬂow

through ‘default’ outlet.

To turn ON To turn OFF

Press the control wheel once,

the water and lights will turn o.

Important note: Risk of scalding, please read the Safety Information on page 1 before using.

Note: The ‘default outlet’ is the outlet that the water ﬂows through

ﬁrst when the control is turned on.

The default outlet is set during installation and can only be

changed from the processor, not the controller.

Turn the control wheel

clockwise, the control will

illuminate Red, the temperature

is displayed and the light will

ﬂash until the set temperature

is reached. After 40 degrees

is reached, one full turn of the

wheel will equal a half degree.

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Setting the water ﬂow

At the same time, press

and turn the control wheel

clockwise to increase the ﬂow

and anti-clockwise to decrease

the ﬂow.

Turn on the control.

Press the menu button and the

option icons will appear.

Rotate the control wheel to

scroll through the icons, when

the required icon is highlighted

press the menu button to

select.

Using the menu (Note: The bath control is used below for demo purposes)

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Diverting the water ﬂow

Accessing the extended menu display

Without turning on the control,

press the menu button and

scroll to the ‘open lock’ icon,

press menu button to select.

The pre-set key code is 000,

this can be changed using the

control wheel as required.

Note: The key icon will have a

question mark above it until it

has been selected or changed.

Press the menu button to

select and the key code will

be displayed, press again and

the display brieﬂy shows if the

extended menu is locked

(a cross) or open (a tick), the

display then closes.

Note: The icon to set a new

code will be activated for 30

minutes each time the control

is turned on, after that the icon

will not show.

Next time the menu is entered

the extended menu can be

viewed.

To ‘lock’ the extended menu

follow the same procedure,

except select the ‘locked’ icon.

Turn on the control.

Press the menu button, the icons

will appear with the ‘un-selected’

outlet icon highlighted.

Press the menu button to select,

the outlet will be diverted, the

temperature will be displayed and

the outlet icon will appear brieﬂy.

Note: The icons only represent a

divert function (images only).

If outlet 3 is selected when the

unit is switched o there will

always be a slight surge of water

through outlet 2 as it’s making its

way back to outlet 1.

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Setting the memory (shower processor only)

Up to three memory settings

can be stored.

Note: Only the ‘default outlet’

temperature can be set to

memory. The max. temp setting

for the memory is 40 degrees.

Press the control wheel

once. The temperature will

be displayed along with the

memory number (1, 2 or 3)

next to the temperature icon.

Set the desired

temperature.

Set the ﬂow rate.

Press the menu button,

scroll to the ‘save’ icon.

Press the control wheel

once and the shower

temperature is now stored.

To access a stored memory;

Whilst in the ‘O’ position,

press the control wheel once

to select memory 1, press twice

for memory 2 and press three

times for memory 3.

The screen will display the

selected memory setting.

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Bath ﬁlling memory option (bath processor only)

Up to three memory settings

can be stored.

Note: To ﬁll the bath from one

of the memory settings the

bath must be connected to the

‘default outlet’. The max. temp

setting for the bath memory is

42 degrees.

Press the control wheel

once. The bath will start to

ﬁll. The temperature will be

displayed along with the

memory number (1, 2 or 3)

next to the temperature icon.

Fill to the desired

temperature and depth.

Press the menu button,

scroll to the ‘save’ icon.

Press the control wheel

once and bath temperature

and depth is now stored.

To access a stored memory;

Whilst in the ‘O’ position,

press the control wheel once

to select memory 1, press twice

for memory 2 and press three

times for memory 3.

The screen will display the

selected memory setting.

DIGITAL

DIGITAL WATER CONTROL AT YOUR FINGERTIPS

Opening and closing pop up bath waste (bath processor only)

This option is only available if

using a *Viega DGX0600C

and DGX0700C drain valve.

(works with Bath processor

only.)

Press the menu button and

select the ‘pop up waste’ icon.

Press the control wheel once

to open or close the pop up

waste.

The icon will display brieﬂy to

conﬁrm.

Press the menu button and

enter the extended menu.

Select the ‘cleaning mode’

icon by pressing the menu

button.

The control will ﬂash Green.

This will disable the controls

for 45 seconds to allow the

controls to be cleaned without

accidentally turning on the

control.

Cleaning (safe) mode

To stop, press the menu button,

scroll to the power icon and

press the menu button.

Indice

Altri manuali Crosswater Sistema di controllo

Crosswater

Crosswater Solo Manuale del prodotto

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente