CTA PAD-PARAFPE Manuale utente
Base Component
for Convertible Printer Shelf Floor Stand
PAD-PARAFPE
INSTRUCTION - MANUAL
CONTENTS:
INSTALLATION:
888-733-4448
1. Assembling base
x2
1A. Combine both halves of the base (B) as shown above. Take (1) unit of
the body (A) and align the mounting holes. Rotate in (4) screws (E) with
provided allen key until securely tightened.
2. Attaching Base Pads
2A. Flip over the now combined base section. Find the base pads (H) and
peel off the sticker to expose the adhesive. Place the foam pads (adhesive
face down on base) at the corners and give it a firm press for a few
seconds until it’s securely attached.
3. Assembling Body Segments
3A. Find the other body unit (A) and the printer shelf component. First
unlock the compartments using the keys (I).Then align holes between
two body units at a time. Take (4) screws (E) and using the provided
allen key tool (G), rotate in the screws as shown until securely tightened.
A
x2
B
x6
I
x4
D
M5 x 6
x12
E
M5 x 12
x4
M
M6 anchor
x2
F
M5 Allen Key
x1
G
x4
H
x2
N
x1
K
Foam Adapter & Sheet Bundle
x1
J
x1
C
A
B
G
E
H
B
A
E
I
B
A
(4)
G
I
I
888-733-4448
4. (Optional) Anchoring Base to Floor
4A. Drill (4) holes into the surface using a power drill or like (not
provided). Take the metal anchor (F) and place the casing into the
holes. Then take the screw end and rotate in with screwdriver (not
included) until securely tightened.
4B. If not anchoring into floor, use the (2) hole fillers (D) to plug in for a
more seamless look.
Setting Up Device
& Enclosure
Lock or unlock your tablet enclosure with security key
as shown
Find the appropriate size foam padding (included) for
the tablet you wish to use. Make sure device is
compatible for the enclosure. Lay in device and
connect any cables/cords as needed.
If needed, lay-in correct included masking insert.
Close and lock enclosure afterwards and you’re set
**Tablet shown for
illustration and
NOT INCLUDED.
**Tablet shown for
illustration and
NOT INCLUDED.
F (4) D (4)
5. Assembling Enclosure to
Printer Shelf Component
5A. Align the VESA holes of the enclosure (J) to
that of the printer shelf component (C). Rotate in
screws (E) from above using provided allen key
tool (G) as shown until securely tightened.
(4) M5 x 12
Cable Routing
Cable Management
Unlock all (3) body unit storage compartments
using the correct key for each section. Fish the
cables through as shown and out the opening
at the very bottom as needed.
G
M
J
C
M
Altri manuali CTA Rack e supporto
CTA
CTA ADD-ADMA Manuale utente
CTA
CTA PAD-PARAFU Manuale utente
CTA
CTA PAD-ASK13B Manuale utente
CTA
CTA PAD-PARAFDC Manuale utente
CTA
CTA PAD-PARAF1 Manuale utente
CTA
CTA PAD-PARAF1GT Manuale utente
CTA
CTA PAD-UAM Manuale utente
CTA
CTA PAD-SWM Manuale utente
CTA
CTA ADD-PARAFS Manuale utente
CTA
CTA PAD-HGTSB Manuale utente
CTA
CTA PAD-SCGS Manuale utente
CTA
CTA ADD-CPOLEGN Manuale utente
CTA
CTA PAD-ASKM6 Manuale utente
CTA
CTA PAD-TAM Manuale utente
CTA
CTA PAD-FTS9 Manuale utente
CTA
CTA PAD-SSMANS Manuale utente
CTA
CTA PAD-ASKP Manuale utente
CTA
CTA PAD-CFWM Manuale utente
CTA
CTA PAD-TPADM Manuale utente
CTA
CTA PAD-VPOS1W Manuale utente
