Dahua Technology IPC-HFW5431E-Z Manuale utente
i
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC 12V or AC 24V in the IEC60950-1. (Power supply requirement is
subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent power
off when necessary.
Please prevent the line cord from being trampled or pressed, especially the plug, power socket and
the junction from the device.
Note: Do not connect these two power supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus; otherwise
it may cause overexposure (It is not the device malfunction), which will affect the longevity of CCD
or CMOS.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and
with strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please do not allow rain or damp to the indoor device in case fire or lightning may occur.
Please keep the sound ventilation in case of heat accumulation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
ii
3. Operation and Daily Maintenance
Please do not touch the heat dissipation component of the device directly in order to avoid scald.
Please do not dismantle the device; there is no component which can be fixed by users themselves
in the machine. It may cause water leakage or bad image for the device due to unprofessional
dismantling. Please contact after-sale service to replace desiccant if it becomes green.
It is recommended to use the device with thunder proof device in order to improve thunder proof
effect.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust
or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if
it is necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean
the device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with
abrasiveness, otherwise it will damage the surface coating or reduce the working performance of
the device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to deal with once dirt is found:
Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or
paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change
the cloth and wipe several times if it is not clean enough.
Warning
Please modify the default password after login in order to avoid being stolen.
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser beam device.
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded content will
be added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurred when using the
device.
iii
Please contact the customer service for the latest procedure and supplementary documentation.
There may be deviation between the actual value of some data and the value provided in the
manual due to the reasons such as the real environment is not stable and so on. Please refer to
the company’s final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the manual.
FCC Information
1. FCC conditions：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference;
This device must accept any interference received, including interference that may cause
undesired operation.
2. FCC compliance：
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Note:
Please refer to the disk for more details, check and download corresponding user’s manual and tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
iv
Table of Contents
1Device Structure .........................................................................................................................1
1.1 Device External Cable .................................................................................................1
1.2 Framework and Dimension.........................................................................................2
1.3 Alarm Setup...................................................................................................................2
2Device Installation ......................................................................................................................5
3Network Configuration...............................................................................................................9
3.1 Modify IP Address........................................................................................................9
3.2 Login WEB Interface..................................................................................................10
1
1Device Structure
1.1 Device External Cable
Note:
The following figure is for reference only, which is used to know the function of cable port.
There are differences about cable structure between different models, please refer to the actual
product for more details.
You can refer to the following figure for cable information. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
No.
Port
Name
Function
Connector
Note
1
AUDIO
OUT
Audio
output port
RCA
Output audio signal to speaker and etc.
2
AUDIO
IN
Audio input
port
RCA
Input audio signal, receive analog audio signal from
pick up and etc.
3
LAN
Network
port
Ethernet
port
Connect to standard Ethernet cable.
Note: Some series don’t support PoE.
4
I/O
I/O port
-
Alarm signal input/output.
5
Power
Power input
port
/
Power port. Input DC 12V or AC 24V power.
Note:
Please connect the DC5.5 round port to 2-pin
converter cable when you are using AC 24V power.
Please use according to device tag.
Please refer to the follow sheet for detailed pin information.
2
Port Name
SN
Name
Note
I/O Port
1
ALARM_NO
Alarm output port. It is to output the alarm signal to the
alarm device.
NO: normal open alarm output port.
It must be used with ALARM_COM.
2
ALARM_COM
Alarm output public port.
3
ALARM_IN1
Alarm input port 1. It is to receive the on-off signal from
the external alarm source.
4
ALARM_IN2
Alarm input port 2. It is to receive the on-off signal from
the external alarm source.
5
GND
Ground port
1.2 Framework and Dimension
Note:
The following figure is for reference only, which is used to know the device dimension.
Please refer to the following figure for dimension information. The unit is mm. See Figure 1- 2.
Figure 1-2
1.3 Alarm Setup
Note:
It is only supported by some series products.
3
Figure 1-3
Alarm input, output description:
Step 1
Connect alarm input device to the alarm input of I/O port cable.
Step 2
Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND of I/O port cable,
Alarm output is the relay switch output; alarm output port can only be connected to NO (normally
open) alarm device.
Step 3
Open the WEB, set alarm input and output correspondingly in alarm setup. Alarm input on the
WEB is corresponding to that of the device I/O port cable. When there is alarm, alarm input
device will generate signal of high and low level. Set corresponding NO and NC inputs.
Step 4
Set alarm output on the WEB, the alarm output is corresponding to the alarm output end of the
device, this is the alarm output port of the I/O port cable.
Please refer to the following figure for alarm input and output information. See Figure 1-4.
Alarm input: When the input signal is idle or grounded, the device can collect the different
statuses of the alarm input port. The input signal is connected to 3.3V or is idle; the device
collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 1-4
Please refer to the following figure for alarm output information. See Figure 1-5 and Figure 1-6.
4
Figure 1-5
Figure 1-6
Mode A:
Level application. Alarm output high and low level, alarm output is OC; it needs to increase pull-
up resistance externally to work normally. Max external pull-up level is 12V, max port current is
300mA (peak). After external pull-up resistance is increased, the default output signal is high
level (external pull-up voltage), and it switches to low level when there is alarm output.
Mode B:
Switch application. Alarm output is used to drive external circuit, max voltage is 12V and max
current is 300mA (peak), it is recommended to use an audible and visual alarm whose model is
H103C.
5
2Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera
and the bracket.
Figure 2-1
Please see Figure 2-1.
Step 1
SD card installation (Optional)
You can see the SD installation card slot, analog output, two direction button and reset
button after you open the lower cover.
Insert the SD card into the slot which is shown in Figure 2-2, you can press the SD card
slightly to insert it because the card slot is elastic.
Figure 2-2
Indice
Altri manuali Dahua Technology Telecamera di sicurezza
Dahua Technology
Dahua Technology NAVIGATOR X1550 Manuale utente
Dahua Technology
Dahua Technology DH-PSDW8842ML-A180-D237 Manuale utente
Dahua Technology
Dahua Technology HAC-HDBW2401RP-Z Manuale utente
Dahua Technology
Dahua Technology DSS4004-S2 Istruzioni generali
Dahua Technology
Dahua Technology D-IPC-HDBW3441F-AS-M-0360B Manuale utente
Dahua Technology
Dahua Technology IPC-HFW2849S-S-IL-0280B Manuale utente
Dahua Technology
Dahua Technology N82AL32 Manuale utente
Dahua Technology
Dahua Technology IPC-HFW1320S-W Manuale utente
Dahua Technology
Dahua Technology N28BL7Z Manuale utente
Dahua Technology
Dahua Technology 8A840WANF Manuale utente
Dahua Technology
Dahua Technology IPC-HDW1531SP Manuale utente
Dahua Technology
Dahua Technology HFW5241E-ZE Manuale utente
Dahua Technology
Dahua Technology IPC-HDW2431T-AS-S2 Manuale utente
Dahua Technology
Dahua Technology 52C230UNI Manuale utente
Dahua Technology
Dahua Technology DH-IPC-HDW3441TP-ZS-S2 Manuale utente
Dahua Technology
Dahua Technology IPC-HFW3841E-AS-0280B-S2 Manuale utente
Dahua Technology
Dahua Technology 50430IC Manuale utente
Dahua Technology
Dahua Technology Lite IPCHFW2231T-ZAS-S2 Manuale utente
Dahua Technology
Dahua Technology Ultra IPC-HFW7442H-Z Manuale utente
Dahua Technology
Dahua Technology IPC-HFW81230E-Z Manuale utente
