Danfoss DHP-R 7UA HPC EM Manuale utente

VMILF102

DHPR&DP

INSTALLATION INSTRUCTIONS

EXPANSION MODULE, HPC EM

COOLING MODULE, HPC CM

VMILF1022 – Danfoss

VMBQI102

VMILF102 Danfoss – 3

Table of contents

Installation for WCS function (warm water loading) ... 4

Installation for TWC function (tap water control)...... 6

Installation for Shunt function ....................... 8

Important information!

24 VAC 1 must not be connected together with:

󰥎

 •24VAC2

 •24VDC

 •Otherequipmentthatuses0-10Vcontrolsignal

 •SignalgroundGND

24 VAC 2 must only be used as power supply to:

󰥎

 •Externalequipmentthatrequires0-10Vcontrolsignal

 •Auxiliarymodules

The two separate 24 VAC circuits must never be connected

󰥎 to each other or to protective ground.

The total power load on 24 VAC 1 respectively 24 VAC 2 must

󰥎 notexceed50VA.

VMILF1024 – Danfoss

VMBQI102

Expansion module, HPC EM

Theoperationaldescriptionfortheexpansionmoduleisavailableinthecontrollermanual.

Installation for WCS function (warm water loading)

Application

TheexpansionmoduleinWCSoperationalmodecontrolswarmwaterloadingofthe

water heaters.

WCS operation is achieved by setting the switch according to the ﬁgure.

Required accessories for installation

Submersiblesensor,Thermokon-DanelkoAKF1004140,itemno.086U3364

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

Other accessories

PilotvalveVVL(2-way),heatexchanger(tapwatervvx),circulationpump.

System image

Heat exchanger

Aheatexchangerisconnectedbetweentheheatpumpandthecirculationforthewaterheatersasdepictedinthesystem

image above.

Circulation pump

Acirculationpumpisconnectedneartheheatexchanger.

Pilot valve

Apilotvalveisconnectedbetweenthecirculationpumpandtheheatexchanger.

Submersible sensor

Asubmersiblesensorisconnectedonthereturnlineoftheheatexchanger,asclosetotheheatexchangeraspossible.

Heat circuit

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Heatexchanger

Modular cable

Steering valve

Circulation pump

Expansion module

WCS operation

Submersible sensor

return VVX

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–5

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheWCSposition



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for WCS operation:

Temperatureinput,T1:Submersiblesensor(heatexchangerreturnline)

Temperatureinput,T2:-

Analogueoutput0-10V,AO1:Signaltopilotvalve

Relay,DO1:Signaltocirculationpump(no-potentialclosure,maximum6A)

Exp.in:ConnectionfromHPCRM

Exp.out:Connectiontopossibleadditionalmodule.

Submersible sensor



• ConnecttoT1andGND

Circulation pump



• ConnecttoDO1.1to24VAC2.1



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2

Pilot valve



• ConnectAO1tothesignalinputofthepilotvalve



• ConnectGNDtopilotvalveGND.IfGNDismissinginthepilotvalve,connectGNDto24VAC2.2somewhereinthe

system. It is most appropriate to jumper terminals 144 and 146 in the controller cabinet.



• ConnectthepilotvalveterminalGto24VAC2.1



• ConnectthepilotvalveterminalG0to24VAC2.2.

•

Exp.in

GGNDG0Y1

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

WCS

24 VAC 2.1

24 VAC 2.2

alt. GG

0Y1

24 VAC 2.1

24 VAC 2.2

AO1

0-10V

Circ. pump

FromExp.out

Submersible sensor

Pilot valve

VMILF1026 – Danfoss

VMBQI102

Installation for TWC function (tap water control)

Application

In the TWC mode, the expansion module ensures that outgoing hot tap wa- ter

and heat water circulation have a suﬃciently high temperature, to prevent the pre-

sence of Legionella bacteria.

TWC operation is achieved by setting the switch according to the ﬁgure.

Required accessories

2 PT1000 strap-on temperature detectors with 2 m of cable, item no.

086U3365(itemnumbercorrespondsto1transmitter)

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

System image

Sensor, water heater

Astrap-ontemperaturedetectorisconnectedonthesupplylineleadoftheendheater,beforethemixingvalve.

Sensor, hot water return

Astrap-ontemperaturedetectoris connectedonthereturnleadofthewarmwatercirculation,beforethecirculation

pump.

Heat circuit

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Modular cable

Sensor, water heater

Electriccartridge

Sensor, hot water return

Expansion module

TWC function

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–7

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheTWCposition



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for TWC operation:

Temperature input, T1: Sensor, water heater

Temperature input, T2: Transmitter, hot water return

Analogueoutput0-10V,AO1:-

Relay,DO1:Signaltoelectriccartridge,hotwater(no-potentialclosure,maximum6A)

Exp.in:ConnectionfromHPCRM

Exp.out:Connectiontopossibleadditionalmodule.

Electric cartridge



• ConnecttoDO1.1to24VAC2.1.



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2.

Sensor, water heater



• ConnectthesensorcabletoT1andGND.

Sensor, hot water return



• ConnectthesensorcabletoT2andGND.

Exp.in

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

TWC

24 VAC 2.1 24 VAC 2.2

Start signal for

electric cartridge

water heater

Hot water return

FromExp.out

VMILF1028 – Danfoss

VMBQI102

Installation for Shunt operation

Application

Intheshuntmode,theexpansionmodulemaintainstherequiredtemperaturefora

second heat circuit.

The shunt function is achieved by setting the switch according to the ﬁgure.

Required accessories

1PT1000strap-ontemperaturedetector,itemno.086U3365

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

Other accessories

Shunt valve, circulation pump.

System image

Sensor, shunt temperature

Astrap-ontemperaturedetectorisconnectedonthesupplylineoftheheatcircuit,afterthecirculationpump.

Heat circuit 1

Heat circuit 2

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Shunt valve

Sensor, shunt temperature

Circulation pump

Modular cable

Expansion module

Shunt function

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–9

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheShuntposition.



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for shunt operation:

Temperature input, T1: Sensor, shunt temperature.

Temperatureinput,T2:-

Analogueoutput0-10V,AO1:Signaltoshuntvalve.

Relay,DO1:Signaltocirculationpump(no-potentialclosure,maximum6A).

Exp.in:ConnectionfromHPCRM.

Exp.out:Connectiontopossibleadditionalmodule.

Sensor, shunt temperature



• ConnecttoT1andGND

Circulation pump



• ConnecttoDO1.1to24VAC2.1.



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2.

Shunt valve



• ConnectAO1tothesignalinputofthepilotvalve.



• ConnectGNDtopilotvalveGND.IfGNDismissinginthepilotvalve,connectGNDto24VAC2.2somewhereinthe

system. It is most appropriate to jumper terminals 144 and 146 in the controller cabinet.



• ConnectthepilotvalveterminalGto24VAC2.1.



• ConnectthepilotvalveterminalG0to24VAC2.2.

Exp.in

GGNDG0Y1

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

Shunt

24 VAC 2.1

24 VAC 2.2

0-10V

alt.

0Y1

24 VAC 2.1

24 VAC 2.2

AO1

Circ. pump

FromExp.out

Shunt temperature

Shunt valve

VMILF10210 – Danfoss

VMBQI102

Inputs and outputs, HPC EM

Temperature inputs

Input Shunt TWC WCS

T1 Shunt temperature HW heater temp WCS temperature

T2 – HW return temp –

Analogue outputs

Outputs Shunt TWC WCS

AO1 Control signal – Control signal

Relay outputs

Outputs Shunt TWC WCS

DO1 Circulation pump Heater HW Circulation pump

Altri manuali Danfoss Unità di controllo

Danfoss

Danfoss AB-QM DN 125 Manuale utente

Danfoss

Danfoss SVA-S Manuale utente

Danfoss

Danfoss Colibri ETS 12C Manuale utente

Danfoss

Danfoss WVS 32 Manuale utente

Danfoss

Danfoss TS 12.5 Manuale utente

Danfoss

Danfoss AME 13 Manuale utente

Danfoss

Danfoss PVG 16 PVH/Covers Manuale

Danfoss

Danfoss ESMD Manuale utente

Danfoss

Danfoss MBC 5000 Manuale utente

Danfoss

Danfoss PVG 120 Manuale utente

Danfoss

Danfoss HPV Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 360 Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente

Danfoss

Danfoss ICF 15 Manuale utente

Danfoss

Danfoss VACON NXP IP00 Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente

Danfoss

Danfoss ASV-P Manuale utente

Danfoss

Danfoss 38E Manuale utente

Danfoss

Danfoss ICSH 25 Manuale utente

Danfoss

Danfoss GBCH Series Manuale utente

Danfoss

Danfoss PVG 32 Manuale

Danfoss

Danfoss SVA-S 6-10 Manuale utente

Danfoss

Danfoss PVG 32 Manuale utente

Danfoss

Danfoss EV250B NC Manuale di istruzioni per l'installazione

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente