Datamax H-Class Manuale utente

Cutter Option

92-2469-01 Rev.B

Overview

This document describes the installation, use and care of the Cutter option for wide model H-Class

printers. After taking a moment to verify the contents of the kit and the tools required, follow the steps

below to install, use and maintain the Cutter option.

Contents

In addition to this procedure, the kit contains the following items:

Item Description

Cutter Assembly

Screw (2)

Tools Required

To install this option, you will need a Phillips screwdriver.

Installing the Cutter

CAUTION

Always remove power before performing installation or maintenance.

1) Turn OFF the Power Switch and unplug

the power cord from the AC Receptacle.

AC Receptacle

Power Switch

2) Raise the cover and remove media.

Remove the Panel, Thumbscrews and

Tear Bar.

Panel

Tear Bar

Thumbscrews

3) Separate the Hinge Plate from the

Cutter Assembly (Item ).

Hinge Plate

Cutter Assembly

4) Carefully press the Hinge Plate onto the

Front Plate and then secure it using the

two Screws (Item ).

Front

Plate

Hinge

Plate

Screws

5) Mount the Cutter Assembly onto the

Mounting Pins of the Hinge Plate.

Hinge

Plate

Cutter

Assembly

Mounting

Pins

6) Plug the Cutter Cable into the Hinge

Plate Jack, and then close the Cutter

Assembly. This completes the

installation.

Cutter

Cable Hinge Plate

Jack

Cutter

Assembly

Using the Cutter

1) Ensure the Media has a clean, straight

edge then load and route it through the

Cutter Opening.(See the Operator’s

Manual for detailed loading information.)

Cutter

Opening

Media

2) Close the cover then plug the power cord

into the AC Receptacle and turn ON the

Power Switch.

AC Receptacle

Power Switch

3) Press the FEED Key on the Front

Panel, and then proceed accordingly:

If cutting standard size labels and a

cut was performed, this completes

installation; or,

If a cut was not performed, see

“Configuring the Printer,” below.

Note: If cutting small labels,

performance may be increased; see

“Increasing Small Label Throughput,”

below.

FEED

Key

Front Panel

Configuring the Printer

The Cutter, a plug and play option, may require configuration if the default setup has changed:

Note: The Cutter can also be controlled by host software commands. Ensure that your labeling

program is properly set to cut, including the desired label size. To test the Cutter, see

“Testing the Cutter”; or, if problems occur, see “Troubleshooting” (below).

a) Press the MENU Key on the printer’s front panel. (See the Operator’s Manual for menu details.)

b) Using the DOWN ARROW Key, scroll to PRINTER OPTIONS then press the ENTER Key.

c) Using the DOWN ARROW Key, scroll to CUTTER then press the ENTER Key.

d) Using the DOWN ARROW Key, scroll to AUTO then press the ENTER Key.

e) Press the ESCAPE Key and then, at the SAVE CHANGES? prompt, select YES.

f) Turn the Power Switch OFF and ON to complete configuration.

Increasing Small Label Throughput

CUT BEHIND is a menu setting that allows the printer to queue then cut a specified number (0 – 2) of

small labels, where the elimination of repeated positioning operations can result in a throughput

increase. To achieve faster throughputs when cutting batches of small labels, follow the procedure

below to establish the queue amount and setup the printer:

a) Measure the length (L) of your media, label edge to label edge including gap, if any.

b) Calculate the Cut Behind number (N): Divide the distance** of 1.24 inches (31.50 mm) by the

length (L) of the media. N = 1.24 ÷ L

**This distance may vary between printers and require slight modification.

c) Calculate the Present Distance (PD): Subtract the product of the length (L) and the Cut Behind

number (N) from the distance** of 1.24 inches (31.50 mm). PD = 1.24 – (N x L)

d) Enter the calculated Present Distance (PD) in the PRINT CONTROL / PRESENT DISTANCE

menu.

e) Enter the calculated Cut Behind number (N) in the PRINTER OPTIONS / CUTTER / CUT

BEHIND menu, and then exit the menu and save your settings.

f) Test the setup: With the media installed, repeatedly press the FEED Key to verify the cut location

– if the location is incorrect adjust the PRESENT DISTANCE accordingly, adding distance to

move the cut farther out or subtracting to move it closer. When satisfactory, the printer is ready

for use.

Notes:

PRINT CONTROL / PRESENT DISTANCE cannot be set to AUTO.

SYSTEM SETTINGS / FAULT HANDLING / VOID AND RETRY should not be used with this

function.

During the setup process some queued blank labels may be lost.

See the Operator’s Manual for menu and other details.

Maintaining the Cutter

To ensure trouble free operation, the Cutter should be cleaned (using the items listed below) after printing

each roll of labels, and more often if the cutting action becomes sluggish.

Recommended Cleaning Items

Isopropyl alcohol

Cotton swabs

Compressed air or soft-bristle brush

CAUTION

Remove power before performing maintenance.

Cutter Blades are SHARP. Keep body parts away from the cutting surfaces.

Never use metal objects on the cutting surfaces.

Take proper precautions when using isopropyl alcohol, a flammable liquid.

Follow these steps to clean the Cutter:

1) Turn OFF the Power Switch and unplug

the power cord from the AC Receptacle.

AC Receptacle

Power Switch

2) Remove media from the printer. Open

the Cutter Assembly, disconnect the

Cutter Cable from the Hinge Plate

Jack, and then remove the Cutter

Assembly from the Hinge Plate.

Cutter

Cable Hinge Plate

Jack

Cutter

Assembly

3) Remove the four Cover Screws and two

Rear Shields from the Cutter

Assembly.

Cover Screws

Rear Shields

Cutter Assembly

(Cabling not shown for clarity.)

4) Remove the Cover from the Mechanism

and then, using compressed air (or a

brush), remove all debris.

Cover

Mechanism

5)Pressing on the Lever to gain access

and using a Cotton Swab dampened

with alcohol (see note below), wipe clean

the Fixed Blade, the Movable Blade,

and the other areas where adhesive has

accumulated.

Cotton Swab

Fixed

Blade

Movable

Blade

Lever

Note: Heavy deposits can be removed using WD-40 (or another non-damaging adhesive

remover) if carefully and sparingly applied using a cotton swab. Never spray directly onto

the assembly; severe damage can result.

6) Place the Cover and the two Rear Shields onto the Mechanism, and then secure all with the four

Cover Screws.

Rear

Shields

Cover

Mechanism

Cover

Screws

7) Place the Cutter Assembly onto the

Hinge Plate then connect the Cutter

Cable to the Hinge Plate Jack. Close

the Cutter Assembly.

Cutter

Cable Hinge Plate

Jack

Cutter

Assembly

8) Load media. Close the cover. Plug the

power cord into the AC Receptacle and

turn ON the Power Switch.

AC Receptacle

Power Switch

Altri manuali per H-Class

Indice

Altri manuali Datamax Etichettatrice

Datamax

Datamax M-Class Mark II Manuale utente

Datamax

Datamax A-Class Mark II Manuale utente

Datamax

Datamax Allegro 2 Manuale utente

Datamax

Datamax Workstation w1110 Manuale utente

Datamax

Datamax RL4e Manuale utente

Datamax

Datamax Prodigy Plus Manuale utente

Datamax

Datamax E-Class Mark III Manuale utente

Datamax

Datamax I-Class Manuale utente

Datamax

Datamax M-Class Mark II Manuale utente

Datamax

Datamax LP3 Manuale utente

Datamax

Datamax I-Class Mark II Manuale utente

Datamax

Datamax MICROFLASH 4T Manuale utente

Datamax

Datamax M-Class Mark II Manuale utente

Datamax

Datamax E Class E-4203 Manuale utente

Datamax

Datamax H-Class Manuale utente

Datamax

Datamax I-Class Manuale utente

Datamax

Datamax I-Class Mark II I-4212E/203 Manuale utente

Datamax

Datamax M-Class Mark II Manuale utente

Datamax

Datamax H-Class Manuale utente

Datamax

Datamax A-Class A-4212 Manuale utente

Datamax

Datamax E-4304 Manuale utente

Datamax

Datamax H-Class Manuale utente

Datamax

Datamax RP Series Manuale utente

Datamax

Datamax MICROFLASH 4TE Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente