Dell PowerEdge 1750 Manuale utente
Dell Poweredge 1750
Installing a ROMB Card (PERC4/DI)
CAUTION: Before you perform this procedure, you must turn off the system and
disconnect it from its power source. For more information, see "Safety First—For
You and Your System" in "Troubleshooting Your System."
CAUTION: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. See your System
Information Guide for complete information about safety precautions, working
inside the computer, and protecting against electrostatic discharge.
NOTICE: To avoid possible data loss, back up all data on the hard drives before changing
the mode of operation of the integrated SCSI controller from SCSI to RAID.
1. Turn off the system, including any attached peripherals, and disconnect the system
from the electrical outlet.
2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your
System."
3. Locate the ROMB card connector on the system board. See Figure A-3.
4. If a PCI card is installed over the ROMB card connector, remove it. See "Removing an
Expansion Card."
5. Position the ROMB card with the notch in its plastic cover facing the redundant power
supply bay, and align the edges of the card with the four plastic standoffs on the
system board.
6. Press down on the three "bulls eyes" on the ROMB card cover until the four plastic
standoffs snap over the edge of the card. See Figure 6-11.
Figure 6-11. Installing the ROMB Card and Backup Battery
7. Install the ROMB backup battery:
a. Position the battery board as shown in Figure 6-11, and press it down into the
two standoffs until it snaps into place.
b. Plug the battery cable into the RAID BATTERY connector on the system board.
8. If you removed a PCI card in step 4, replace it. See "Installing an Expansion Card."
9. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your
System."
10. Reconnect the system and peripherals to their power sources, and turn them on.
11. Enter the System Setup program and verify that the setting for the SCSI controller has
changed to reflect the presence of the RAID hardware. See "Using the System Setup
Program" in your User's Guide.
12. Install the RAID software. See the ROMB card software documentation for more
information.
Removing a ROMB Card
CAUTION: Before you perform this procedure, you must turn off the system and
disconnect it from its power source. For more information, see "Safety First—For
You and Your System" in "Troubleshooting Your System."
CAUTION: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. See your System
Information Guide for complete information about safety precautions, working
inside the computer, and protecting against electrostatic discharge.
NOTICE: To avoid possible data loss, back up all data on the hard drives before changing
the mode of operation of the integrated SCSI controller from SCSI to RAID.
1. Turn off the system, including any attached peripherals, and disconnect the system
from the electrical outlet.
2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your
System."
3. If a PCI card is installed over the ROMB card, remove the PCI card. See "Removing an
Expansion Card."
4. Pull the ROMB card up out of the four standoffs. See Figure 6-11.
5. Disconnect the ROMB backup battery from the backup battery connector, and pull the
battery assembly up out of the two standoffs. See Figure 6-11.
6. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your
System."
Altri manuali per PowerEdge 1750
7
Indice
Altri manuali Dell Server
Dell
Dell PowerEdge C6145 Guida rapida
Dell
Dell PowerEdge 2800 Manuale di istruzioni
Dell
Dell PowerEdge T350 57C92 Manuale
Dell
Dell EMC XC Core XC650 Manuale
Dell
Dell EMC E39S Series Manuale
Dell
Dell PowerEdge R820 Manuale utente
Dell
Dell PowerEdge R630 Manuale utente
Dell
Dell Wyse ThinOS T10 Manuale utente
Dell
Dell PowerVault DL2300 Manuale utente
Dell
Dell PowerEdge UPS 500T Manuale di istruzioni
Dell
Dell PowerEdge C6220 Manuale
Dell
Dell PowerEdge 2500 Manuale utente
Dell
Dell DR4300 Manuale utente
Dell
Dell PowerEdge R415 Manuale utente
Dell
Dell PowerEdge M630 Manuale utente
Dell
Dell EMC PowerEdge R640 Manuale
Dell
Dell Precision KR019 Manuale utente
Dell
Dell PowerEdge R330 Manuale utente
Dell
Dell EMC PowerEdge R350 Manuale
Dell
Dell PowerEdge 2410 Manuale utente
