Dell PowerEdge 2550 Manuale utente

www.dell.com

support.dell.com

Dell™ Systems

ACTIVATING THE DELL PERC 3/DI

Notes, Notices, Cautions, and

Warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous

situation which, if not avoided, may result in severe injury.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of

Dell Computer Corporation is strictly forbidden.

Trademarks used in this text:

Dell

PowerEdge

, and the

DELL

logo are trademarks of

Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any

proprietary interest in trademarks and trade names other than its own.

February 2001 P/N 448VG Rev. A00

Activating the Dell PERC 3/Di 1-1

Activating the Integrated RAID Controller

This document explains how to activate your Dell™ system’s PowerEdge™ expandable

RAID controller 3/Di (PERC 3/Di). Your upgrade kit includes a RAID controller memory

module, RAID hardware key, RAID battery, and RAID software.

WARNING: Before you perform this procedure, you must turn off the system and

disconnect it from its electrical outlet. For more information, see “Safety

First—For You and Your Computer” in your system’s

Installation and

Troubleshooting Guide

NOTICE: To avoid possible data loss, back up all data on the hard-disk drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

CAUTION: See “Protecting Against Electrostatic Discharge” in the safety

instructions in your

System Information

document.

1Open the system doors.

See “Opening the System Doors” in your system Installation and

Troubleshooting Guide.

2Open the ejectors on the RAID controller memory module socket by pressing down

and outward, which allows you to insert the memory module into the socket.

See Figure 1-1 for the location of the socket on the system board.

1-2 Activating the Dell PERC 3/Di

www.dell.com | support.dell.com

Figure 1-1. System Board Features

hardware key connector for

optional RAID controller

memory module socket

for optional RAID

controller

RAID controller

battery connector

Activating the Dell PERC 3/Di 1-3

3Align the memory module's edge connector with the slot in the center of the memory

module socket, and insert the memory module into the socket (see Figure 1-2).

The memory module socket has two alignment keys that allow you to install the

memory module in the socket in only one way.

NOTE: The RAID controller memory module must be an unbuffered memory module, rated

to run at 100 MHz or faster. Do not substitute registered memory modules such as those

used for system memory.

4Press the memory module with your thumbs while pulling the ejectors with your index

fingers to lock the memory module into the socket (see Figure 1-2).

Figure 1-2. Installing a Memory Module

5Examine the RAID hardware key (see Figure 1-3) to ensure that it is labeled for your

system.

Hardware keys intended for use in other systems will not enable the RAID controller.

6If the key is the correct type, install the key in its socket on the system board

(see Figure 1-1) and secure the key with the latches on each end of the socket

(see Figure 1-3).

alignment keys (2)

memory module

socket ejectors (2)

1-4 Activating the Dell PERC 3/Di

www.dell.com | support.dell.com

Figure 1-3. Installing the RAID Hardware Key

7Insert the RAID battery into the bracket on the underside of the system door

(see Figure 1-4).

Figure 1-4. Installing the RAID Battery

socket

latches (2)

RAID hardware key

RAID battery

system door

Activating the Dell PERC 3/Di 1-5

8Connect the battery cable to the RAID battery connector on the system board

(see Figure 1-1).

9Close the system doors, reconnect the system and peripherals to their electrical

outlets, and turn them on.

10 Enter the System Setup program and verify that the setting for the SCSI controller has

changed to reflect the presence of the RAID hardware.

See “Changing the System Setup Settings.”

11 Install the RAID software.

For more information, see the RAID controller documentation.

Changing the System Setup Settings

1Turn on your system.

If your system is already turned on, shut the system down and then turn it on again.

2Press <F2> immediately after you see the following message:

Press <F2> for System Setup

If you wait too long and your operating system begins to load into memory, allow the

system to complete the load operation, and then shut down the system and try again.

NOTE: To ensure an orderly system shutdown, see the documentation that accompanied

your operating system.

3Press <Alt><p> to switch to Page 2 of the System Setup screen.

• If the system detects the new RAID controller memory module and RAID

hardware key, the system displays the RAID option in the Integrated Devices

section of the screen.

• If the system displays the SCSI option, it did not detect the integrated RAID

controller. Ensure that the RAID hardware key and RAID memory module are the

correct type and repeat all hardware installation steps found earlier in this

document.

NOTICE: To avoid possible data loss, back up all data on the hard-disk drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1-6 Activating the Dell PERC 3/Di

www.dell.com | support.dell.com

4Press the left- or right-arrow key to change the RAID option to RAID Enabled.

Channel A displays RAID, and Channel B displays SCSI. (When the RAID option is

set to SCSI, Channel A and Channel B display SCSI.)

5Press <Alt><b> to save settings, and then reboot the system.

6Configure the RAID subsystem and install the RAID driver and management software.

For more information, see the PERC 3/Di controller documentation.

www.dell.com

support.dell.com

Systèmes Dell™

ACTIVATION DE DELL PERC 3/DI

Remarques, avis, précautions et

avertissements

REMARQUE : Une REMARQUE indique une information importante qui

peut vous aider à mieux utiliser votre ordinateur.

AVIS : Un AVIS vous avertit d’un risque de dommage matériel ou de perte de

données et vous indique comment éviter le problème.

PRÉCAUTION : Une PRÉCAUTION vous avertit d’une situation

qui, si elle n'est pas évitée, peut entraîner des blessures plus ou

moins graves.

AVERTISSEMENT : Un AVERTISSEMENT vous avertit d’une

situation qui, si elle n'est pas évitée, peut entraîner des blessures

graves.

____________________

Les informations contenues dans ce document sont sujettes à modification sans préavis.

Toute reproduction, sous quelque forme que ce soit, sans l'autorisation écrite de

Dell Computer Corporation est strictement interdite.

Marques utilisées dans ce texte :

Dell

PowerEdge

, et le logo

DELL

sont des marques de

Dell Computer Corporation.

D'autres marques et noms commerciaux peuvent être utilisés dans ce document pour

faire référence aux entités se réclamant de ces marques et de ces noms ou à leurs produits.

Dell Computer Corporation dénie tout intérêt propriétaire vis-à-vis des marques et des noms

commerciaux autres que les siens.

Février 2001 P/N 448VG Rév. A00

Altri manuali per PowerEdge 2550

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Dell Server

Dell

Dell OptiPlex 9020 Manuale utente

Dell

Dell DX6000G Manuale utente

Dell

Dell PowerEdge T105 Systems Manuale utente

Dell

Dell PowerEdge T710 Manuale tecnico

Dell

Dell PowerEdge R910 Manuale

Dell

Dell PowerEdge T100 Manuale utente

Dell

Dell EMC PowerEdge MX740c Manuale utente

Dell

Dell poweredge VRTX Manuale utente

Dell

Dell PowerEdge R610 Manuale utente

Dell

Dell External OEMR R210II Manuale utente

Dell

Dell Force10 S2410-01-10GE-24P Manuale utente

Dell

Dell EMC PowerEdge T440 Manuale

Dell

Dell PowerEdge 1950 Manuale utente

Dell

Dell PowerEdge 1600SC Manuale utente

Dell

Dell PowerEdge 1500SC Manuale tecnico

Dell

Dell PowerEdge R620 Manuale utente

Dell

Dell PowerEdge T620 Manuale utente

Dell

Dell PowerEdge M420 Manuale operativo

Dell

Dell PowerEdge XK946 Manuale utente

Dell

Dell PowerEdge T110 Manuale utente

Dell

Dell PowerEdge R760xs Manuale

Dell

Dell PowerEdge 1955 Manuale utente

Dell

Dell PowerEdge C8000 Manuale utente

Dell

Dell PowerEdge 1955 Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente

Planet

Planet NAS-7410 Manuale utente

Lenovo

Lenovo ThinkSystem SR635 V3 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX900 Manuale utente

Asus

Asus RS700DA-E6 PS4 Manuale utente