Dell PowerEdge 6800 Manuale tecnico

www.dell.com | support.dell.com

Dell™ PowerEdge™ 6800 Systems

Information Update

信息更新

Mise à jour des informations

Aktuelle Informationen

アップデート情報

설명서 갱신본

Actualización de información

www.dell.com | support.dell.com

Dell™ PowerEdge™ 6800 Systems

Information Update

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarksusedinthistext:Dell,theDELLlogo,andPowerEdgearetrademarksofDellInc.;IntelisaregisteredtrademarkofIntelCorporation;

MicrosoftandWindowsareregisteredtrademarksandWindowsServerisatrademarkofMicrosoftCorporation;RedHatisaregisteredtrademark

of Red Hat Corporation; SUSE is a registered trademark of SUSE LINUX Products GmbH.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

September 2006 P/N F3227 Rev. A09

Information Update 3

Information Update

This document provides information for your system on the following topics:

• Reconfiguring the system for regional power requirements

• Processor upgrades

• Adaptec SCSI Card 39160 expansion-card slot restrictions

• System start-up behavior

• Integrated NIC IPMI port functionality

• Remote Access Controller card interaction with integrated video

• System messages

• Environmental data sheets

• Removing and installing the cooling shroud

• Linux operating system information

– Booting Red Hat

Enterprise Linux AS (Version 4) for Intel

x86 with more than eight logical

processors

– Using more than eight logical processors with Red Hat Enterprise Linux (Version 4)

for Intel Extended Memory 64 Technology (Intel EM64T)

– Rebooting Red Hat Enterprise Linux AS (Version 4) for Intel EM64T

– NIC device names

• Microsoft

Windows Server

™

2003 installation with more than eight logical processors

• Microsoft Windows

2000 installation

• Console redirection—escape key sequences

CAUTION: Only trained service technicians are authorized to remove the system cover and access any of

the components inside the system. Before performing any procedure, see your Product Information Guide for

complete information about safety precautions, working inside the computer, and protecting against electrostatic

discharge.

4Information Update

Reconfiguring the System for Regional Power Requirements

CAUTION: If you relocate a system operating in the 120–127 VAC or 200–240 VAC range to a different geographic

area, ensure that jumper CB_TYPE matches the AC line voltage range of your new location.

If the new power source is less than 120 VAC and you do not reconfigure jumper CB_TYPE for the lower voltage

power source, damage to the system power cable or the system itself may occur.

Table 1-1

lists countries where the AC line voltage may be less than 120 V. Confirm the power source in your

particular location and reconfigure the CB_TYPE jumper if necessary.

Table 1-2 and Figure 1-1 show the settings and location of the CB_TYPE jumper.

Table 1-1. Areas Where AC Line Voltage May Be Less Than 120 V

AC Line Voltage Country

100 V Japan, Korea, Okinawa

105 V Korea

110 V Anguilla, Azores, Belgium, Belize, Bolivia, Brazil, Colombia, Curacao, Dominican

Republic, Ecuador, El Salvador, France, Guam, Guyana, Haiti, Honduras, Jamaica,

Lebanon, Panama, Peru, Philippines, Somalia, Surinam, Tahiti, Taiwan, Turkey, Virgin

Islands

115 V Aruba, Barbados, North Mariana Island, St. Pierre & Miquelon, Surinam, Tonga,

Trinidad & Tobago

Table 1-2. Power Configuration Jumper Settings

Jumper Setting Description

CB_TYPE AC line voltage is 120 V or greater*

(default) AC line voltage is less than 120 V

* This jumper is not functional for systems using a line voltage in the range of 200–240 VAC.

Information Update 5

Figure 1-1. Power Configuration Jumper Location

Processor Upgrades

If you add one or more processors to your system, ensure that all processors have the same stepping value

and the same cache size and technology. If you install processors with different speeds, they will operate

at the speed of the slowest processor.

You must install all voltage regulator modules (VRMs) included in the upgrade kit, in addition to the

processors. See "Processors" in your

Installation and Troubleshooting Guide

for details on installing processors

and VRMs.

Adaptec SCSI Card 39160 Expansion-Card Slot Restrictions

If you add an Adaptec SCSI Card 39160 to a system running the Microsoft Windows 2000 Server operating

system, and a Dell™ Remote Access Controller 4/P (DRAC 4/P) card is installed in expansion-card slot 7,

the Adaptec 39160 card must be installed in expansion-card slot 2.

Memory Test at System Start-Up

The

System Memory Testing

option in the System Setup program is disabled by default. If the option is

enabled, the system memory is tested at each system startup. Systems with large memory configurations

may take more time to complete the memory test. See your

User’s Guide

for information on the System

Setup program.

6Information Update

System Start-Up Behavior

The following system behaviors during system start-up are normal and do not indicate a problem with the

system:

• When AC power is applied to the system, if the System Setup program’s

AC Power Recovery

option is

not set to allow the system to power up when AC power is applied, the cooling fans will spin-up briefly

and then stop. (See your

User’s Guide

for information on the System Setup program.)

• It may take 30 seconds or longer for video to display after the system is powered on.

Integrated NIC IPMI Port Functionality

If you configure the integrated NIC for Intelligent Platform Management Interface (IPMI) pass-through

traffic, and you also configure the system to boot from the network using the same IPMI port, the NIC

will not be available for management traffic during system boot. After system boot is completed, IPMI

functionality is automatically restored.

In addition, if you configure the NIC to support IPMI management traffic, the NIC driver’s Large-Send

Offload (LSO) feature will be disabled on that port.

Remote Access Controller Card Interaction With Integrated Video

If you install an optional remote access controller card for remote systems management, the system’s front

and back panel video ports will be disabled.

System Messages

Table 1-3 provides an updated list of system

status messages that the system’s front panel

LCD may

display at system start-up, if a memory error occurs. See "System Messages" in your

Installation and

Troubleshooting Guide

for additional information about system messages.

Information Update 7

Table 1-3. LCD Status Messages

Line 1

Message

Line 2

Message

Causes Corrective Actions

SYSTEM

SYSTEM NAME SYSTEM ID is a unique name,

five characters or less, defined by

the user.

SYSTEM NAME is a unique

name, 16 characters or less,

defined by the user.

The system ID and name display

under the following conditions:

• The system is powered on.

• The power is off and active

POST errors are displayed.

This message is for information

only.

You can change the system ID

and name in the System Setup

program. See your User's Guide

for instructions.

E0000 OVRFLW CHECK LOG LCD overflow message.

A maximum of three error

messages can display sequentially

on the LCD. The fourth message

displays as the standard overflow

message.

Check the SEL for details on the

events.

E1000 FAIL SAFE Failsafe event. Capture the event log and see

"Getting Help" in your

Installation and Troubleshooting

Guide.

E1000 MISCONFIG Missing or improperly installed

VRMs.

See "Installing a Processor VRM"

in your Installation

and Troubleshooting Guide. If

the VRMs appear to be properly

configured and installed, see

"Getting Help" in your

Installation and Troubleshooting

Guide.

E0119 TEMP AMBIENT Ambient system temperature

is out of acceptable range.

See "Troubleshooting System

Cooling Problems" in your

Installation and Troubleshooting

Guide.

E0119 TEMP PROC # The specified processor is out

of acceptable temperature range.

See "Troubleshooting System

Cooling Problems" in your

Installation and Troubleshooting

Guide.

8Information Update

E0119 TEMP PLANAR System board temperature is out

of acceptable temperature range.

See "Troubleshooting System

Cooling Problems" in your

Installation and Troubleshooting

Guide.

E0212 PROC VTT Processor VTT voltage is out

of acceptable voltage range.

See "Troubleshooting Power

Supplies" in your Installation

and Troubleshooting Guide.

E0212 VOLT PG nSystem power supply is out of

acceptable voltage range; faulty

or improperly installed power

supply.

See "Troubleshooting Power

Supplies" in your Installation

and Troubleshooting Guide.

E0212 VOLT PG nVideo Video voltage is out of acceptable

voltage range.

See "Getting Help" in your

Installation and Troubleshooting

Guide.

E0212 VOLT BATT ROMB Faulty RAID battery. Replace the RAID battery.

See "Activating the Optional

Integrated RAID Controller"

in your Installation

and Troubleshooting Guide.

E0212 VOLT BATT CMOS Faulty system battery. See "Troubleshooting the System

Battery" in your Installation

and Troubleshooting Guide.

If the problem persists, see "

Getting Help" in your Installation

and Troubleshooting Guide.

E0276 PROC # STATUS Faulty or improperly installed

processor.

See "Troubleshooting the

Microprocessors" in your

Installation and Troubleshooting

Guide.

E0276 PROC # VCORE The VCORE voltage of the

specified processor is out of

acceptable range.

See "Troubleshooting the

Microprocessors" in your

Installation and Troubleshooting

Guide. If the problem still

persists, see "Getting Help"

in your Installation

and Troubleshooting Guide.

Table 1-3. LCD Status Messages (continued)

Line 1

Message

Line 2

Message

Causes Corrective Actions

Altri manuali per PowerEdge 6800

Indice

Lingue:

Altri manuali Dell Server

Dell

Dell PowerEdge C5125 Manuale utente

Dell

Dell PowerEdge 6350 Manuale utente

Dell

Dell PowerEdge 1300 Manuale di installazione e funzionamento

Dell

Dell Wyse ThinOS T10 Manuale utente

Dell

Dell XC6320 Manuale utente

Dell

Dell E14S Series Manuale utente

Dell

Dell PowerEdge R210 Manuale tecnico

Dell

Dell PowerEdge C5220 Manuale utente

Dell

Dell KGR3H Manuale

Dell

Dell EMC PowerEdge T340 Manuale

Dell

Dell PowerEdge C410X Manuale elenco delle parti

Dell

Dell PowerEdge UPS 500T Manuale utente

Dell

Dell PowerEdge R310 Manuale utente

Dell

Dell 6100 Guida

Dell

Dell PowerEdge systems 6300 Manuale utente

Dell

Dell PowerEdge R830 Manuale utente

Dell

Dell PowerEdge R210 Manuale utente

Dell

Dell PowerEdge 1855 Manuale tecnico

Dell

Dell PowerEdge M610 Guida rapida

Dell

Dell PowerEdge E02B Manuale utente

Dell

Dell 1955 Manuale utente

Dell

Dell PowerEdge B02S Manuale utente

Dell

Dell PowerEdge XR7620 Manuale

Dell

Dell PowerEdge T605 Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente

Planet

Planet NAS-7410 Manuale utente

Lenovo

Lenovo ThinkSystem SR635 V3 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX900 Manuale utente

Asus

Asus RS700DA-E6 PS4 Manuale utente