Dell PowerEdge C6105 Manuale utente
Dell PowerEdgeC6105
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Regulatory Model B03S
Dell PowerEdgeC6105
Getting Started
With Your System
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make
better user of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss
of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Information in this publication is subject to change without notice.
© 2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of
Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of
Dell Inc. AMD®is a registered trademark and AMD Opteron™ is a trademark of Advanced
Micro Devices, Inc. Red Hat Enterprise Linux®and Enterprise Linux®are registered
trademarks of Red Hat, Inc. in the United States and/or other countries. Novell®is a registered
trademark and SUSE™ is a trademark of Novell Inc. in the United States and other countries.
Citrix®and XenServer®are either registered trademarks or trademarks of Citrix Systems, Inc.
in the United States and/or other countries. VMware®is a registered trademarks or trademarks
of VMWare, Inc. in the United States or other countries.
Other trademarks and trade names may be used in this publication to refer to either the entities
claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in
trademarks and trade names other than its own.
Regulatory Model B03S
July 2010 P/N 45F0M Rev. A00
Getting Started With Your System | 3
CAUTION: Restricted Access Location
This server is intended for installation only in restricted access locations as
defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions
apply:
•Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location
and about any precautions that shall be taken.
•Access is through the use of a tool or lock and key, or other means of
security, and is controlled by the authority responsible for the location.
Installation and Configuration
WARNING: Before performing the following procedure, review and
follow the safety instructions that came with the system.
Unpacking the System
Unpack your system and identify each item.
Installing the Tool-Less Rail Solution
WARNING: Whenever you need to lift the system, get others to assist
you. To avoid injury, do not attempt to lift the system by yourself.
WARNING: The system is not fixed to the rack or mounted on the rails.
To avoid personal injury or damage to the system, you must adequately
support the system during installation and removal.
WARNING: To avoid a potential electrical shock hazard, a third wire
safety grounding conductor is necessary for the rack installation.
The rack equipment must provide sufficient airflow to the system to
maintain proper cooling.
CAUTION: When installing rails in a square-hole rack it is important to
ensure that the square peg slides through the square holes.
4|Getting Started With Your System
1Align the end pieces of the rails on the vertical rack flanges to seat the
pegs in the bottom hole of the first U and the top hole of the second U.
Engage the back end of the rail until the latch locks in place.
NOTE: The rails can be used in both square-hole (item 1 in figure below)
and round-hole racks (item 2 in figure below).
2Repeat step 1 to position and seat the front end piece on the vertical
flange.
NOTE: To remove the rails, pull on the latch release button on the end
piece midpoint and unseat each rail.
3Slide the system into the rack.
Getting Started With Your System | 5
4If present, remove the chassis stabilizer shipping bracket (optional)
from the rack.
NOTE: To remove the rails, pull on the latch release button on the end
piece midpoint and unseat each rail.
5Tighten the thumbscrews to secure the ears of system to the front of
the rack.
6|Getting Started With Your System
Optional –Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which
cable to plug into each connector. Be sure to tighten the screws (if any) on
the monitor’s cable connector.
Getting Started With Your System | 7
Connecting the Power Cable (s)
Connect the system’s power cable(s) to the system and, if a monitor is used,
connect the monitor’s power cable to the monitor. Plug the other end of the
power cables into a grounded electrical outlet or a separate power source
such as an uninterrupted power supply or a power distribution unit.
8|Getting Started With Your System
Turning On the System
Press the power button(s) either on the front or back of the system and
the monitor. The power indicators should light.
Altri manuali per PowerEdge C6105
6
Indice
Lingue:
Altri manuali Dell Server
Dell
Dell PowerEdge M420 Manuale utente
Dell
Dell PowerEdge 1400SC Manuale del proprietario
Dell
Dell PowerEdge R320 Manuale utente
Dell
Dell PowerEdge M630 Manuale utente
Dell
Dell PowerEdge C6145 Manuale utente
Dell
Dell Force10 C150 Manuale utente
Dell
Dell PowerEdge 2650 Manuale utente
Dell
Dell 8 Manuale utente
Dell
Dell PowerEdge M620 Manuale utente
Dell
Dell PowerEdge R660xs Manuale
Dell
Dell PowerEdge HR675 Manuale utente
Dell
Dell PowerEdge T420 Guida rapida
Dell
Dell PowerEdge E02B Manuale utente
Dell
Dell X95FF Manuale
Dell
Dell PowerEdge C5125 Manuale utente
Dell
Dell PowerEdge 1750 Manuale di istruzioni
Dell
Dell Wyse ThinOS T10 Manuale utente
Dell
Dell W-Series Manuale utente
Dell
Dell PowerEdge R610 Istruzioni di montaggio
Dell
Dell PowerEdge PDU Managed LED Manuale utente
