Delta UNOnext Manuale utente

Indice

Altri manuali Delta Strumento di misura

Delta

Delta DPM-D520I Manuale utente

Delta

Delta MessageMaxx DMS-279 Manuale

Delta

Delta EMS 32-011 Manuale utente

Delta

Delta LTL-XL Manuale utente

Delta

Delta SS1-UM-1.05 Manuale utente

Delta

Delta DPM-C530 Manuale utente

Delta

Delta RetroSign GR1 Manuale utente

Delta

Delta TECK II Manuale utente

Delta

Delta dvp04pt-s Manuale utente

Delta

Delta UT-191T Manuale utente

Delta

Delta DVP-ES2 Manuale utente

Delta

Delta XVR5116HS-I2 Manuale utente

Delta

Delta DPM-MA1121 Manuale utente

Delta

Delta XVR5432L-I2 Manuale utente

Delta

Delta DPM-D510 Manuale utente

Delta

Delta DPM-C320 Manuale utente

Delta

Delta LD-100E-M22 Manuale utente

Delta

Delta DPM-C501L Manuale utente

Delta

Delta UNO-C07X011 Manuale utente

Delta

Delta RetroSign GRX Manuale utente

Delta

Delta DPM-C501L Manuale utente

Delta

Delta DPM-C520 Manuale utente

Delta

Delta PPM P1_120 Manuale utente

Delta

Delta RetroSign GRX-1 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

1

UNOnext Wiring Guide

ver 1.5

2021/6/23

2

As long as UNOcentral is connected to a power supply, the system will begin to operate.

Through the HDMI connection on the back of UNOcentral, UNOcentral's screen can be output

to displays with HDMI interfaces, such as computer monitors and TVs. UNOcentral is managed

through a web GUI. Users can remotely manage UNOcentral through the browsers of other

hosts, or directly output UNOcentral to a display and use a USB keyboard and mouse for man-

agement. To use UNOcentral remote management or other network services, it is recommend-

ed to connect the network cable to the LAN1 port on the back of UNOcentral (The MAC address

of LAN1 is provided on the UNOcentral’s label). As shown in Figure 1

If RS485 communication interface is used between UNOcentral and UNOnext, they must be

used Daisy-Chain, and the communication mode is Modbus/RTU protocol. It is recommend-

ed to use 22AWG multi-core shielded twisted pair cable or above to achieve the best re-

sults. The simple wiring instructions is below, please use the RS485 adapter include in the

box (Please plug-in on the COM1 of the UNOcentral).

3

UNOnext can directly connect to a controller with RS485 interface, up to 16 devices can be connect-

ed to one controller.

If the UART sengs of UNOnext have been modied, please modify to the default sengs

above before connecng to UNOcentral.

The Modbus slave address of UNOnext can be set by dip switch following below table. Oth-

ers detail UNOnext sengs can be referred the UNOnext user manual. Table 2 Set Modbus slave

address of UNOnext

The UART conguraons of the UNOcentral and UNOnext

Baud Rate: 9600

Data-bit: 8

Parity: None

Stop-bit: 1

4

1. Prepare tools and connector.

2. Connect signal lines.

3. Tighten the screws 4. Need to fix the plastic sheet.

Step of operation.

5

5. Close the lid

6. Install connector on the COM1 of UNOcentral

6

7. Connect the HDMI cable, mouse, and keyboard to the screen to confirm that the number of

UNOnext is the same as the number and sensor data are shown on the screen.

If the sensor data does not show value at all or the number of devices is incorrect, please

check below checklists

◇Are all UNOnext power on?

◇Is RS485 wiring problem?

◇Do use the wrong pin hole?

◇Does follow RS485 installation guideline?

◇All of UNOnext should be used different modbus slave address.