Denver DSB-4010MK2 Manuale utente
Sound Bar User Manual
Operating Introduction
a. Place the Soundbar on a flat and solid surface. Alternatively, you can wall mount the Soundbar with the
screws provided. You can hear audio through the Soundbar using ONE of the following connections.
1. Connect to your television using one of the connectors.
⚫HDMI-ARC connector on the TV (using an HDMI cable)
⚫Optical output connector on the TV (using an optical cable)
⚫Headphone jack (using the supplied audio cable with 3.5mm plug)
2. Connect to a Bluetooth enabled device.
3. Connect to a USB drive (stick) loaded with music files
b. Illustration of the Soundbar connectors for different connections
EN
EN
OPTICAL IN
OPTICAL IN
HDMI-ARC
HDMI-ARC
LINE IN
LINE IN
DC 19V IN
DC 19V IN
c. The control panel on the Soundbar
EN
EN
Hold down /MODE for Power
On/Standby.
Hold down /MODE for Power
On/Standby.
Press the /MODE button to toggle the
sources: Bluetooth -> USB Drive ->
Line In -> HDMI-ARC -> Optical In
Press the /MODE button to toggle the
sources: Bluetooth -> USB Drive ->
Line In -> HDMI-ARC -> Optical In
Press/Hold down II / MUTE for
Pause/Play. (USB Drive)
Press/Hold down II / MUTE for
Pause/Play. (USB Drive)
Press/Hold down II / MUTE for Mute /
No Mute. (Line In)
Press/Hold down II / MUTE for Mute /
No Mute. (Line In)
Hold down VOL+ /I for Volume up.
Hold down VOL+ /I for Volume up.
Press VOL+ /I for Next USB Drive
Song.
Press VOL+ /I for Next USB Drive
Song.
Hold down VOL- / I for Volume
down.
Hold down VOL- / I for Volume
down.
Press VOL- / I for Previous USB
Drive Song.
Press VOL- / I for Previous USB
Drive Song.
d. Source selection shown on the LED display
Line In source
Bluetooth source
USB source when connecting to a USB drive. USB
source cannot be selected if no USB drive is
connected.
HDMI-ARC source
Optical In source
Notes:
⚫“bt” (Bluetooth) flashes if the Soundbar is not paired or connected to a Bluetooth device.
⚫“bt (Bluetooth) lights up if the Soundbar is paired or connected to a Bluetooth device.
⚫When the Soundbar is switched to standby, the red light is turned on.
e. Remote control buttons
Switch the product on or to standby
Mute or restore volume
Increase volume
Decrease volume
Skip to previous audio file during USB play
Skip to next audio file during USB play
Start or pause play during USB play
Repeat audio play during USB play
EQ
Select different preset sound settings
MODE
Select an audio source
Press the EQ button to toggle different preset sound
settings shown below.
Display
EQ mode
Eq0
Normal
Eq1
Rock
Eq2
Pop
Eq3
Classic
Eq4
Jazz
Eq5
Country
f. Importance Notice for soundbar mounting on the wall:
1) Wall- mounted installation must be carried out by qualified personnel only.
Incorrect assembly can result in severe personal injury and property damage! (If you intend to
install this product yourself, you must check for installations such as electrical wiring and plumbing,
which may be hidden inside or behind the wall.)
2) It is the installer’s responsibility to verify and confirm that the wall will safely support the total load of
the unit and wall brackets.
3) Additional tools (not included) are required for the installation.
4) Do not overtighten screws.
5) Use an electronic stud finder to check the wall type before drilling and mounting
6) The proposed height on the wall is 1.0~1.5meters
Technical Specification
Power/Amps: Input: AC110~240V, 50/60Hz, Output: DC19V, 1.5A
Power consumption: 28.5W
Max output power: 40W
Working temperature: 0~35o C
Bluetooth version: 5.0
Operating frequency range: 2402-2480Mhz
Soundbar measurement: 80cm x 6cm x 6cm
Bluetooth name: DSB-4010MK2
Packing List
. Sound bar
. Manual
. 3.5mm to 3.5MM audio cable
. Flat head screws (D7.5 * L25mm) x 2
. Remote control with batteries
. Mains Power supply
Please notice - All products are subject to change without any notice. We take
reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment contains materials, components and
substances that can be hazardous to your health and the environment, if the
waste material (discarded electric and electronic equipment) is not handled
correctly.
Electric and electronic equipment is marked with the crossed out trash can
symbol, seen above. This symbol signifies that electric and electronic equipment
should not be disposed of with other household waste, but should be disposed of
separately.
All cities have established collection points, where electric and electronic
equipment can either be submitted free of charge at recycling stations and other
collection sites, or be collected from the households. Additional information is
available at the technical department of your city.
Hereby, Inter Sales A/S declares that the radio equipment type DSB-4010MK2 is
in compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.denver-electronics.com and then click the search ICON on topline of website.
Write modelnumber: DSB-4010MK2.Now enter product page, and red directive is
found under downloads/other downloads
Operating Frequency Range: 2402-2480Mhz
Max Output Power: 40W
DENVER ELECTRONICS A/S
Omega 5A, Soeften
DK-8382 Hinnerup
Denmark
www.facebook.com/denverelectronics
Indice
Altri manuali Denver Altoparlanti
Denver
Denver BTL-324 Manuale utente
Denver
Denver BPS-455NR Manuale utente
Denver
Denver BTS-200 Manuale utente
Denver
Denver IPT-400 Manuale utente
Denver
Denver BTV-208 Manuale utente
Denver
Denver BTB-410 Manuale utente
Denver
Denver BTP-103 Manuale utente
Denver
Denver BTS-120 Manuale utente
Denver
Denver TSP-205 Manuale utente
Denver
Denver TSP-505MK2 Manuale utente
Denver
Denver BTS-400 Manuale utente
Denver
Denver BTV-150RO Manuale utente
Denver
Denver BTS-31 Guida di riferimento
Denver
Denver IFI-1500 Manuale utente
Denver
Denver TSP-503 Manuale utente
Denver
Denver BTV-230 Manuale utente
Denver
Denver BTL-70 Manuale utente
Denver
Denver TSP-305 Manuale utente
Denver
Denver BTS-21 Manuale utente
Denver
Denver BTL-62 Manuale utente
