Desco D19431 Istruzioni per l'installazione e il funzionamento

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

Body Voltage Meter

Installation, Operation and Maintenance

Description

The Statguard Flooring D19431 Body Voltage Meter

is a portable measuring system that allows analysis

of charge levels accumulated on the human body

according to ANSI/ESD STM97.2. The Body Voltage

Meter measurement may be logged using internal

memory. Logged measurements can be exported and

further reviewed on a PC. Graphs of measurements can

be displayed on the LCD display for quick evaluation.

Each Body Voltage Meter is calibrated with accepted

procedures and standards traceable to the National

Institute of Standards and Technology (NIST) and

includes a NIST certificate.

November 2020

“A compliance verification plan shall be established to

ensure the organization’s fulfilment of the requirements

of the plan. Process monitoring (measurements) shall be

conducted in accordance with a compliance verification

plan that identifies the technical requirements to be

verified, the measurement limits and the frequency at

which those verifications shall occur. The compliance

verification plan shall document the test methods

used for process monitoring and measurements. If the

organization uses different test methods to replace

those of this standard, the organization shall be able

to show that the results achieved correlate with the

referenced standards. Where test methods are devised

for testing items not covered in this standard, these shall

be adequately documented including corresponding

test limits. Compliance verification records shall be

established and maintained to provide evidence of

conformity to the technical requirements. The test

equipment selected shall be capable of making the

measurements defined in the compliance verification

plan.” (EN 61340-5-1 clause 5.2.4)

Packaging

1 Body Voltage Meter

1 Walking Test Probe

1 Black 8-Pin DIN to USB Cable, 1.8 m long

1 Black Ground Cord with Crocodile Clip, 5 m long

1 Lanyard with Hook

1 Certificate of Calibration

Figure 1. Statguard Flooring Body Voltage Meter

TECHNICAL BULLETIN TB-9058

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

Features and Components A. Settings Button: Press to enter SETTINGS mode.

B. Left and Right Buttons: Press to cycle through the

menus.

C. Cursor Button: Press to advance the cursor.

D. Exit Button: Press to power the meter ON and OFF.

This button is also used to exit SETTINGS and MENU

modes.

E. Start / Stop Button: Press to start and stop a

measurement. This button is also used to increase the

value of settings when in SETTINGS mode.

F. Ground Jack: Common point ground for the meter.

Connect the included black ground cord here.

G. Probe / PC Connector: Connect the included test

probe when taking measurements. Connect the included

DIN to USB cable when exporting data onto a PC.

H. Ground Jack: Common point ground for the meter.

Connect the included black ground cord here.

I. Ground Touch Plate: Touch to ground the operator

prior to taking body voltage measurements.

Settings Mode

Press and hold the Settings button for 1 second to enter

the SETTINGS mode. There are 4 menus available:

1. V RANGE

2. CLOCK

3. DISPLAY

4. °

Press the Left button to move to the previous menu.

Press the Right button to move to the next menu.

Press the Exit button to exit from SETTINGS mode.

V. Range Menu

Figure 2. Body Voltage Meter features and components

F G H

Adjust the voltage range for new and saved graphs.

Press the Cursor button to advance the cursor, and

press the Start / Stop button to increase the value.

NOTE: AUTO range is only available for saved graphs.

B B

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

Clock Menu Monitor Mode

Adjust the date and time settings. Press the Cursor

button to advance the cursor, and press the Start / Stop

button to increase the value.

Display Menu

Adjust the contrast of the LCD display (0 to 9). The

default contrast setting is 5. Press the Start / Stop

button to increase the value.

FMenu

Choose Celsius (

C) or Fahrenheit (

° F

) for the

temperature unit of measurement. Press the Start / Stop

button to toggle the setting.

Operation Modes

There are 6 operation modes available:

1. MONITOR

2. ZERO

3. NEW

4. VIEW

5. CLEAR

6. COM

Press the Left button to move to the previous mode.

Press the Right button to move to the next mode.

Press the Start / Stop button to enter the selected mode.

Press the Exit button to exit the selected mode.

Allows on-the-go measurements without saving any

data.

Zero Mode

Zeros out the Body Voltage Meter.

New Mode

Records new graph.

View Mode

Views saved graphs.

Clear Mode

Deletes last or all saved graphs.

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

COM Mode Operation

Using the Meter

1. Press the EXIT button to power the meter.

2. Hold the test probe and momentarily touch the

ground touch plate located on the back of the unit.

Figure 4. Momentarily touching the ground touch plate to

ground the operator

Exports data to PC using supplied 8-Pin DIN to USB

cable.

Installation

1. Remove the meter from the carton.

2. Connect the included ground cord to one of the

two ground jacks located at the top of the meter.

Connect the opposite end of the ground cord to

equipment ground.

3. Connect the test probe to the probe connector

located at the top of the meter.

4. Press the EXIT button to power the meter.

5. NOTE: The electronic components of the

electrostatic sensor require a warm-up period

of 5 minutes to obtain accurate and stable

measurements. The sensor uses a vibrating

element to perform measurements, and the

warm-up period allows its mechanical assembly

to stabilize. An exclamation mark symbol on the

display and an audible sound will alert the operator

once warm-up has been completed.

Figure 3. Setup of the Body Voltage Meter

3. Verify the Body Voltage Meter is zeroed by toggling

to the MONITOR menu and reading the measured

value. It should be 0 V. Zero the Meter if required by

toggling to the ZERO menu.

Monitor Mode

1. Toggle to MONITOR mode on the meter, and press

the Start / Stop button.

2. The display will show the electrical potential present

on the probe.

3. A beeping sound (every second) indicates that the

meter is measuring. This is to ensure the unit is not

left in measuring mode unintentionally and cause

the battery to drain.

4. To stop the measuring process, press the Start /

Stop or Exit buttons.

6. The meter is now ready for use.

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

Datalogger Mode

1. Toggle to NEW mode on the meter and press the

Start / Stop button.

2. After a 3 second count-down, the Body Voltage

Monitor will log a graph of the walking test.

3. The graph will show the positive and negative peak

voltages measured during the test.

Downloading Data to a PC

1. Download and install the WT Manager software.

2. Connect the Body Voltage Meter to a PC using the

included Black 8-Pin DIN to USB Cable.

3. Toggle to COM mode on the meter.

4. Run the WT Manager software and select the

appropriate port from the drop-down menu.

Figure 5. Using the Body Voltage Monitor

4. To stop the test, press the Start / Stop button.

5. Press the Left or Right buttons to scroll through the

graph for quick evaluation.

6. Press the Start / Stop button again to save or

discard the graph. Press Start / Stop button to save

or the Cursor button and Start / Stop button to

discard the graph.

Figure 6. Selecting a COM port using the WT Manager

software

Figure 7. Viewing the body voltage of an ungrounded

operator in the WT Manager software

One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: StatguardFlooring.com

Employee Owned

Specications

Voltage Range ±1050 V

Accuracy ±5 V

Resolution 1 V

Input Resistance 1014 ohms

Power Supply 6 AA alkaline batteries

Battery Auto-Shut O󰀨

Timer

10 minutes

Display Graphic LCD 128 x 64 pixel,

68 mm x 51 mm

Memory Capacity 10 graphs

Sample Rate 200 Hz

Max Total Graphs

Duration

2 minutes and 30 seconds

PC Interface USB

Operating Temperature 41 ºF to 85 ºF (5 ºC to 30 ºC)

Environmental

Requirements

Indoor use only at altitudes

less than 6500 ft. (2 km)

Maximum relative humidity of

80 % up to 85 °F (30 °C)

Dimensions

(meter)

9.6" x 5.1" x 2.4"

(243 mm x 130 mm x 60 mm)

Dimensions

(probe)

Ø 1.4" x 5.1"

(Ø35 mm x 130 mm)

Weight

(meter with batteries)

1.4 lbs (650 g)

Weight

(probe)

0.6 lbs (0.27 kg)

Country of Origin Italy

Maintenance

Battery Replacement

Replace the batteries if the battery indicator on the Body

Voltage Meter begins blinking. Open the battery cover,

replace the 6 alkaline batteries, and close the battery

compartment.

Figure 9. Replacing the Batteries on the Body Voltage

Meter

Figure 8. Viewing the body voltage of a grounded

operator in the WT Manager software

Limited Warranty, Warranty Exclusions, Limit of

Liability and RMA Request Instructions

See the Statguard Flooring Warranty -

StatguardFlooring.com/Limited-Warranty.aspx

Indice

Altri manuali Desco Strumento di misura

Desco

Desco 19258 Istruzioni per l'installazione e il funzionamento

Desco

Desco 98132 Documento tecnico

Desco

Desco 19787 Manuale del proprietario

Desco

Desco 19290 Istruzioni per l'installazione e il funzionamento

Desco

Desco Statguard Flooring D19290 Istruzioni per l'installazione e il funzionamento

Desco

Desco 19665 Istruzioni per l'installazione e il funzionamento

Desco

Desco Meg Pocket Megohmmeter Manuale di servizio

Desco

Desco 19430 Istruzioni per l'installazione e il funzionamento

Desco

Desco TB-3048 Manuale di servizio

Desco

Desco 19651 Istruzioni per l'installazione e il funzionamento

Desco

Desco 19665 Istruzioni per l'installazione e il funzionamento

Desco

Desco TB-3076 Manuale utente

Desco

Desco TB-3081 Manuale di servizio

Desco

Desco SCS-73627 Istruzioni per l'installazione e il funzionamento

Desco

Desco TB-3081 Istruzioni per l'installazione e il funzionamento

Desco

Desco 19492 Guida all'installazione

Desco

Desco 19350 Manuale di servizio

Desco

Desco 19492 Guida all'installazione

Desco

Desco Combo Tester X3 Istruzioni per l'installazione e il funzionamento

Desco

Desco 19492 Guida all'installazione

Desco

Desco 19494 Guida alla risoluzione dei problemi

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente