DFI 586OP Manuale utente

586OP

System Board

User’s Manual

-D24941007-

No part of this document may be copied or reproduced

in any form or by any means without the prior written

consent of DFI, Inc.

DFI, Inc. makes no warranties with respect to this

documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular

purpose. The information in this document is subject to

change without notice. DFI, Inc. reserves the right to

make revisions to this publication and to make changes

to any and/or all parts of its content, at any time,

without obligation to notify any person or entity of such

changes. Further, DFI, Inc. assumes no responsibility

for any errors that may appear in this document.

DFI is a registered trademark, and 586OP is a trade-

mark of Diamond Flower, Inc. All other product names

mentioned are trademarks or registered trademarks of

their respective companies.

vFCCStatementonClassB

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential

installation. This equipment generates, uses, and can

radiate radio frequency energy and if not installed and

used in accordance with the instruction manual may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

the receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modification not expressly approved

by the party responsible for compliance could void

the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

v Table of Contentsv

Introduction ..............................................................................

Features and Specifications ................................................

Package Checklist ...............................................................

Installation Overview ...............................................................

Preparing the Area ..............................................................

Handling the System Board ................................................

Tips in Handling the System Board ..............................

Hardware Installation..........................................................

Memory Installation ......................................................

Installing the Modules ............................................

Board Configuration ......................................................

Jumper Settings for CMOS Clean, Display Type

and PS/2 Mouse................................................

Jumper Settings for Parallel Port ...........................

Cache Configuration ..............................................

Jumper Settings for Cache Memory .................

CPU Installation ............................................................

Jumper Settings for CPU .......................................

Installing Upgrade CPUs .......................................

Built-in Ports ........................................................................

Serial Ports ...................................................................

Parallel Port ..................................................................

Floppy Disk Drive Connector ........................................

IDE Hard Disk Connector .............................................

PS/2 Mouse Port ..........................................................

Installing Expansion Cards .................................................

Installing the System Board ................................................

1-1

1-2

1-4

2-1

2-2

.2-2

2-2

2-6

2-7

2-8

2-11

2-13

2-14

2-16

2-17

2-18

2-23

2-24

2-25

2-27

2-28

2-31

2-32

2-33

Initial Setup Program ................................................................

Award BIOS CMOS Setup Utilities ......................................

Standard CMOS Setup ..................................................

BIOS Features Setup .....................................................

Chipset Features Setup .................................................

PCI Configuration Setup ................................................

Load BIOS Defaults .......................................................

Load Setup Defaults ......................................................

Password Setting ...........................................................

IDE HDD Auto Detection ...............................................

Save & Exit Setup ..........................................................

Exit Without Saving ........................................................

IDE Device Drivers ....................................................................

Troubleshooting Checklist ........................................ .............

Appendix A:Types of Modules .............................. ...............

Appendix B:System Error Report .........................................

Appendix C:Memory & I/O Maps ...........................................

Appendix D:PCI I/O Pin Assignments ..................................

Appendix E:ISA I/O Pin Assignments ..................................

Appendix F:Connector Pin Assignments ............................

Appendix G:Award BIOS Hard Disk Table ...........................

3-1

3-2

3-5

3-7

3-8

3-9

3-10

3-11

3-12

4-1

5-1

A-1

B-1

C-1

D-1

E-1

F-1

G-1

PCI/ISASystemBoard

vIntroduction

The 586OP system board offers several advanced fea-

tures integrated into the system board. Its design is

based on the new Peripheral Component Interconnect

(PCI) local bus and Industry Standard Architecture

(ISA) standards.

The 586OP supports a 273-pin Zero Insertion Force

(ZIF) CPU socket for PentiumTM processors running at

60MHz or 66MHz frequency. This ZIF socket allows

users to easily upgrade their CPUs. It also supports a

Flash EPROM for easy BIOS upgrades. Flash EPROM

is a memory chip for the storage of BIOS which can be

erased in bulk or modified using a software utility.

The 586OP is equipped with four PCI and four ISA

slots, of which one pair is shared.

Equipped with two built-in PCI IDE connectors, the

586OP system board can control four drives and sup-

ports fast Mode 3 hard drives and hard drives larger

than 528MB under DOS. The system board is also

equipped with two serial ports, an ECP/EPP parallel

port, a floppy disk drive controller, and one mini-DIN-6

connector for the PS/2 mouse.

The 586OP can be configured to twenty-two different

memory sizes ranging from 2MB to 128MB using

256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 and

8Mx36 72-pin SIM modules.

1-1 uIntroduction

586OP

Features and Specifications

Introduction u1-2

Processor

•

Intel Pentium

TM 60/66MHz

Chipset

•OPTI: Python chipset

82C546, 82C547 - system and cache controller

82C606 - data buffer

82C206 - IPC controller

82C822 - PCI bridge

Architecture

•PCI/ISA

PCI IDE Interface

•Fast PCI local-bus interface

•Supports fast Mode 3 (Enhanced IDE) hard drives

•Two IDE connectors to control four drives (e.g. two

HDDs, one tape drive and one CD-ROM)

•Uses NS PC87410 PCI IDE chip

Super I/O Interface

•Two NS16C550A-compatible serial ports

•PS/2 mouse port

•One parallel port with EPP and ECP support

•Supports 360KB, 720KB, 1.2MB, 1.44MB and

2.88MB floppy drives

•Uses NS PC87332VF super-I/O controller

BIOS

•Award Plug & Play BIOS

•Flash EPROM for easy BIOS upgrades

•Supports IDE HDDs larger than 528MB under DOS

(LBA mode only)

PCI/ISASystemBoard

1-3 uIntroduction

Cache Memory

•256K, 512K or 1MB direct map write-back or

write-through cache

•Uses 32Kx8, 64Kx8 or 128Kx8 SRAM

Memory Onboard

•Up to 128MB (depends on the operating system)

•Four 72-pin SIMM sockets

•Supports single and/or double density SIMMs

•256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 or

8Mx36 SIMMs

•Supports 60ns or 70ns fast page mode DRAM

Expansion Slots

•Three dedicated PCI slots

•One shared PCI/ISA slot

•Three dedicated 16-bit ISA slots

Due to the size of the CPU with accompanying

heatsink/fan component, the following slots have

size limitations:

ISA slots 2, 3 and 4 will be limited to 2/3 length

ISA cards.

PCI slots 1 and 2 will be limited to 3/4 length PCI

cards.

ZIF Socket

•273-pin ZIF socket (Intel Socket 4)

Board Dimensions

•33cm (12.87") x 22cm (8.58")

Baby AT form factor

586OP

Package Checklist

The 586OP package contains the following items:

•The 586OP system board

•The 586OP user’s manual

•Two IDE driver diskettes

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port

cables

If any of these items is missing or damaged, please

contact your dealer or sales representative for assistance.

Introduction u1-4

PCI/ISASystemBoard

vInstallation Overview

This chapter summarizes the steps in installing the

586OP system board into your system unit. It also

includes a description of the area in which you must

work and directions for memory installation. Before

installing the system board, obtain the memory you plan

to install. Please refer to the memory chart on pages 2-3

and 2-4 for the number and type of SIM modules

needed for the amount of memory you require.

Preparing the Area

Before unpacking the system board, make sure the

location you have selected is relatively free of dust and

static electricity. Excessive exposure to dust, static

electricity, direct sunlight, excessive humidity, extreme

cold and water can damage the operational capabilities

of your system board. Avoid soft surfaces such as beds

and carpeted floors which can hinder air circulation.

These areas also attract static electricity which can

damage some circuits on your system board.

Be sure that the power source has a properly grounded,

three-pronged socket. It is essential that the power

connection be properly grounded for correct functioning

of your system board. For further protection, we recom-

mend that you use a surge suppressor. This will protect

the system board from damage that may result from a

power surge on the line.

Move items that generate magnetic fields away from

your system board, since magnetic fields can also

damage your system board. Once you have selected the

ideal location, unpack the 586OP system board care-

fully.

2-1 uInstallation Overview

Indice

Manuali Scheda madre popolari di altre marche

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente