DFI G4E620-N Manuale utente

935-G4E622-000(G)

A75720516

G4E620-N

G4E620-B

System Board

User’s Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for

identification purpose only and are the properties of the respective

owners.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

An electronic file of this manual is included in the CD. To view the

user’s manual, insert the CD into a CD-ROM drive. The autorun

screen (Main Board Utility CD) will appear. Click “User’s Manual” on

the main menu.

Table of Contents

Chapter 1 - Introduction

Features................................................................................................................................................

Special Features of the System Board....................................................................

Package Checklist.......................................................................................................................

Chapter 2 - Hardware Installation

System Board Layout ...........................................................................................................

System Memory............................................................................................................................

CPU.........................................................................................................................................................

Jumper Settings.............................................................................................................................

Rear Panel I/O Ports..............................................................................................................

I/O Connectors............................................................................................................................

Chapter 3 - BIOS Setup

Award BIOS Setup Utility...................................................................................................

Updating the BIOS...................................................................................................................

Chapter 4 - Supported Softwares

Drivers, Utilities and Software Applications.......................................................

Installation Notes........................................................................................................................

102

104

111

Introduction

Appendix A - Watchdog Timer

Watchdog Timer.....................................................................................................................

Appendix B - System Error Messages

POST Beep................................................................................................................................

Error Messages.......................................................................................................................

Appendix C - Troubleshooting

Troubleshooting Checklist.............................................................................................

Appendix D - Watchdog Timer

Watchdog Timer.....................................................................................................................

112

115

117

121

Introduction

Specifications

Processor

The system board is equipped with Socket 478 for installing one of

the following supported processors.

• Intel®Pentium®4 (Prescott and Northwood) processor

- Intel Hyper-Threading Technology

- FSB: 400MHz and 533MHz

• Intel®Celeron®/ Celeron®D processor

- 400MHz system data bus

• Processor socket: Socket 478

Chipset

• Intel®845E chipset

- Intel®82845E Memory Controller Hub (MCH)

- Intel®82801DB I/O Controller Hub (ICH4)

System Memory

• Two 184-pin DDR SDRAM DIMM sockets

• 2.5V unbuffered PC1600 (DDR200) or PC2100 (DDR266)

DDR SDRAM DIMM

• Supports maximum of 2.1GB system memory using 64Mbit,

128Mbit, 256Mbit or 512Mbit technology

- Double-sided x16 DDR SDRAM DIMM is not supported

• Supports ECC function

Chapter 1 - Introduction

Density Width

Single/Double

184-pin DDR

64 Mbit

SS/DS

64/128MB

X16

SS/DS

32MB/NA

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/NA

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/NA

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/NA

Introduction

BIOS

• Award BIOS

• 4Mbit flash memory

Energy Efficient Design

• Supports ACPI specification and OS Directed Power

Management

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard

- Wake-On-Ring (through internal or external modem)

- Wake-On-LAN

- RTC timer to power-on the system

• System power management supported

• CPU stopped clock control

• Hardware supports SMI green mode

• Microsoft®/Intel®APM 1.2 compliant

• Soft Power supported - ACPI v1.0b specification

• AC power failure recovery

Hardware Monitor

• Monitors CPU/system temperature and overheat alarm

• Monitors 5VSB/VBAT/1.5V/3.3V/±5V/±12V/Vcore voltages and

failure alarm

• Monitors CPU/chassis/2nd fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan

speed

• Opened chassis alarm

• Watchdog timer function

Introduction

Onboard Audio Features

• 18-bit stereo full-duplex codec with independent variable

sampling rate

• High quality differential CD input

• True stereo line level outputs

• S/PDIF-out interface

• 2-channel audio output

PCI IDE Interface

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

Onboard LAN Features

• Uses 82551 fast ethernet controller (G4E620-N only)

- Integrated IEEE 802.3, 10BASE-T and 100BASE-TX

compatible PHY

- Glueless 32-bit PCI master interface

- Glueless CardBus master interface

- Integrated power management functions

- 128 Kbyte Flash interface

- Thin BGA 15 mm2package

• Uses 82562 fast ethernet controller

- Basic 10/100 Client Connection. Supports 559 level cable

and PHY Stats. Support for Server OS included as check

item, but no Server function included

- Same Quality Driver suits as 82559

- Supports DMI/SNMP/WMI

- 10/100 Auto Sensing

- IEEE 802.3, 10BASE-T/100BASE-TX compliant physical layer

interface

- IEEE 802.3u Auto-Negotiation

- 48-pin SSOP, 3.3V device

Accelerated Graphics Port (A.G.P.)

• Supports 1.5V AGP with up to 1066MB/sec. bandwidth for 3D

graphics applications

Introduction

Rear Panel I/O Ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 2 DB-9 serial ports

• 2 RJ45 LAN ports (G4E620-N only)

1 RJ45 LAN port (G4E620-B only)

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line-out

I/O Connectors

• 1 CompactFlashTM socket

• 1 connector for 2 additional external USB 2.0/1.1 ports

• 1 connector for an external game/MIDI port

• 1 front audio connector for external line-out and mic-in jacks

• 2 internal audio connectors (CD-in and AUX-in)

• 1 S/PDIF-out connector

• 1 connector for IrDA interface

• 2 IDE connectors

• 1 floppy connector

• 1 20-pin ATX power connector

• 1 4-pin ATX 12V power connector

• 1 Wake-On-LAN connector

• 1 Wake-On-Ring connector

• 1 chassis open connector

• 1 keylock connector

• 1 front panel connector

• 3 fan connectors

Expansion Slots

• 1 AGP slot that supports 1.5V AGP

• 4 PCI slots (1 shared with ISA slot)

• 3 ISA slots

Compatibility

• PCI 2.2 and AC ’97 compliant

PCB

• 4 layers, ATX form factor

• 30.5cm (12") x 24.4cm (9.6")

Altri manuali per G4E620-N

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Scheda madre popolari di altre marche

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente