Digi One SP Manuale utente
February 5, 2004
Using the Digi One SP to Network Doppler Systems
DDF6001s using an Ethernet
A Technical Application Note from Doppler Systems Inc.
Introduction
The Digi One SP allows a device with a serial port to be connected to an Ethernet. This
application note describes the connections and setup required to use the Digi One SP with
the Doppler DDF6001 direction finders. (Note that this application note also applies to
older DDF6001 direction finders).
Network Configuration
The figure below shows the configuration of the network when using the Digi One SP.
Each Digi One device is a terminal server that allows one connection. Therefore, only
one computer connected to the network can control and monitor the direction finder sites.
If it necessary to have multiple computers monitor the DF network, then BearingTrack
Server (see BearingTrack manual) must be used instead of the Digi One SP.
Ethernet
Computer
DF RX
Digi One
SP
Digi One
SP
DF RX
DF RX
Digi One
SP
Programming the Digi One SP
The Digi One SP comes with a CD that contains the software necessary to set it up. First
connect the Digi One SP to its power supply and then connect it to the network using a
standard category 5 networking cable. Insert the CD and wait for the set up program to
launch. The Digi Device Setup wizard should also automatically start. Press Next on the
first page of the wizard. The wizard will locate the Digi One device. Select the device
and press Next. Set the IP address and subnet mask of the device consistent with your
network. Each Digi One SP device must have a unique IP address in order to work with
the BearingTrack software. Set the IP address and make a note of the address you set.
Press the next button and select Incoming Connection. Press the Next button and select
Incoming Network Connection. Press Next and select TCP Sockets. Press Next and
set the serial port parameters to Baud Rate 2400, Data bits 8, Parity None, Stop Bits 1,
and Flow Control None. Press Next and verify the settings you’ve entered and then press
Next again and wait for the Digi One SP to reboot (takes about 1 minute).
If you want to modify any of the settings, the Digi One comes with a built in web server
so you can use a web browser (e.g. Internet Explorer) to modify the settings. Refer to the
Digi One SP manual for instructions on how to use a web browser to modify its settings.
Configuring the DDF6001
During the normal setup of the DDF6001 WinRDFCommand is used to set the CIV
address of the DF and to change other settings if needed. To use WinRDF Command
first connect J1 on the DDF6001 to the computer using a serial RS232 cable. Launch the
WinRDFCommand program. Set up the DDF6001 as you desire and then press the Auto
Output On radio button to switch the DF into the automatic output mode. Automatic
output must be enabled to use the DF6001 with the Digi One SP.
Configuring Bearing Track
When setting up the sites in Bearing Track (see manual or help file) select the Enable
Internet Connection checkbox for each site and enter the IP address of the Digi One SP
device at that site location. Enter 2101 for the port number.
Installing the Digi One SP
Connect the serial connector on the Digi One SP to J1 of the DF600. Connect a category
5 cable from the Digi One SP to your network connection. Connect the power supply
included with the Digi One SP to the unit.
Operation
Use BearingTrack as described in the BearingTrack manual or help files.
Altri manuali per One SP
6
Indice
Altri manuali Digi Server
Digi
Digi Modem Digi One IA Manuale utente
Digi
Digi Connect IT 16 Manuale utente
Digi
Digi PortServer TS 1 M MEI Manuale utente
Digi
Digi Connectware PortServer TS 1 + Modem Manuale utente
Digi
Digi PortServer TS M MEI Manuale utente
Digi
Digi ConnectPort LTS 8 Manuale utente
Digi
Digi EL 2 Manuale utente
Digi
Digi PortServer TS 8 Manuale utente
Digi
Digi 1002 Manuale
Digi
Digi TS 4 MEI Manuale utente
Digi
Digi PortServer TS 8 Manuale di istruzioni
Digi
Digi Connectware Digi CM 16 Manuale utente
Digi
Digi Connect IT 4 Manuale utente
Digi
Digi ConnectPort LTS 8 Manuale utente
Digi
Digi ConnectPort LTS 8 Manuale di installazione
Digi
Digi DC-ES-4SB Manuale utente
Digi
Digi One IAP Haz Manuale utente
Digi
Digi PortServer CM Manuale utente
Digi
Digi Connect Wi-SP Manuale utente
Digi
Digi DIGI CONNECT ES Manuale operativo
