dji DROP SYSTEM NAV LIGHT EDITION Manuale utente
!
DROP SYSTEM USER GUIDE
(NAV LIGHT EDITION)
MAVIC 2 & MAVIC 2 ENTERPRISE
Oct 2020
v1.0
1
In This Guide…
Parts and Components 3.......................................................................................
In the Box 4.................................................................................................................
Installation and Usage 5.........................................................................................
Attaching a Payload 13...........................................................................................
Troubleshooting 16...................................................................................................
Warranty and Service 19........................................................................................
Terms of Use 20........................................................................................................
2
Parts and Components
Your Drop System is designed and assembled entirely by DJI
Shop Canada staff in-house. All major components, with the
exception of a few parts, are 3D printed and assembled by
hand to ensure a sturdy and reliable build. A breakdown of the
parts and components are indicated in the illustrations below.
3
1. Manual Pin Release Button
2. Security Lock
3. Main Clip Assembly
4. Servo and Servo Protector Box
2
3
4
5
1
7
5. Servo Arm
6. Payload Pin
7. Electronics Box and Cover
8. Navigation Light Sensor Clip
Your unit may differ slightly from the depicted
illustrations in this user guide
6
8
Parts and Components (cont…)
In the Box
4
9
11
9. Payload Drop Indicator (Lit when pin is in the open position)
10. Power Indicator (Lit when powered on)
11. Power Switch (Down = ON, Up = OFF)
10
1x Drop System Assembly
1x Security Lock
1x Electronics Box Cover
1x Payload Pin
1x 150mAh Li-Po Battery
1x Battery USB Charger
2x Carabiner Clips
Installation and Usage
To ensure that your Drop System functions correctly, we
recommend following the installation and usage guidelines
detailed below. Should a part or component not function as
explained, please contact DJI Shop Canada for support.
Step 1
It is recommended to
pre-install your landing
gear risers of choice
(not included) to ensure
adequate clearance
between the lower
portion of the Drop
System and the ground
below it.
Step 2
Hold the aircraft upright
with one hand while
using the other hand to
gently press the main
clip assembly upwards
from the belly of the
aircraft. The electronics
box must be on the
right side of the aircraft.
5
Installation and Usage (cont…)
Step 3
The clip will snap into place when fully installed. Ensure that
the downward vision and IR sensors are not obstructed. The
clip must sit between the vision sensor and IR sensor on the
belly of the aircraft.
6
Installation and Usage (cont…)
Step 4
Ensure that the clip
reaches the top of the
battery. Install the clip
security lock by
inserting into one side
of the clip, then
stretching to meet the
other side of the clip.
This will require some
force, as the lock is designed to keep tension on the clip,
ensuring it cannot detach itself from the aircraft body.
7
Installation and Usage (cont…)
Step 5
Remove the M1 (Front-Right) landing gear extension (if
installed) and fold the arm towards the stowed position.
Step 6
Slide the navigation light sensor clip upwards towards the
motor. It will require slight force to cover the light. Ensure that
the wire stays behind the arm and does not get caught.
8
Installation and Usage (cont…)
Step 7
Extend the arm outwards
once the navigation light
sensor clip has been
installed. Ensure that the
wire does not get caught
while performing this
action. Once the arm is
extended, there will be
tension on the wire, ensuring that it does not droop.
Step 8
Reconnect the landing
gear extension to the
arm.
9
Installation and Usage (cont…)
Step 9
Remove the electronics box cover by pulling the upper part
towards you, then rotating downward to free the lower latch.
Step 10
Connect the battery to the battery connector inside the
electronics box and tuck the battery inside. Be sure to connect
the battery in the proper orientation. Do not force the
connector.
10
Indice
Altri manuali dji Accessori per droni e quadricotteri
dji
dji ZENMUSE L1 Manuale utente
dji
dji E800 Manuale utente
dji
dji DF03 Manuale utente
dji
dji MATRICE 300 RTK Manuale utente
dji
dji RoboMaster RMEM01 Manuale utente
dji
dji MATRICE 300 RTK Manuale utente
dji
dji Zenmuse X9 Manuale utente
dji
dji FC7BMC Manuale utente
dji
dji M200 Series Manuale utente
dji
dji FC7BMC Manuale utente
dji
dji RC 2 Manuale utente
dji
dji AGRAS T50 Manuale utente
dji
dji GO 4 Manuale utente
dji
dji ZENMUSE H20 Series Manuale utente
dji
dji ZENMUSE H20T Manuale utente
dji
dji E-Port Development Lit Manuale utente
dji
dji HG8001606 Manuale utente
dji
dji Goggles Manuale utente
dji
dji Snail 6048-3D Manuale utente
dji
dji AGRAS T30 Manuale utente
